Sharp MX-M363N / MX-M363U / MX-M503N / MX-M503U (serv.man18) Service Manual ▷ View online
MX-M503N MX-FN10 7 – 5
2)
Connect the finisher connector with the connector of the main
unit, and tighten the screw.
unit, and tighten the screw.
G. Staple position label attachment
1)
Attach the label to the position indicated in the figure.
[For scanner] (package part No. 10)
[For scanner] (package part No. 10)
[For DSPF/RSPF] (package part No. 11)
H. Turn on the power of the main unit
1)
Insert the power plug of the main unit into the power outlet.
2)
Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit.
Turn ON the power switch in the front cabinet of the main unit.
3)
Turn ON the power switch on the operation panel.
Label attachment
reference
* Corner of the
reference
* Corner of the
"upper cabinet rear"
Corner R end fitting
Corner R end fitting
1mm
1mm
1mm
1mm
DSPF
RSPF
ON
MX-M503N MX-PNX5A/B/C/D 8 – 1
MX-M503N
Service Manual
[8] MX-PNX5A/B/C/D
1. Unpacking
A. Removal of the punch unit
B. Check the packed items
1)
Check that all the items are included in the package.
* Use the punch position labels bundled with the MX-FN10.
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
A. Turn off the power of the main unit
1)
Turn OFF the power switch on the operation panel.
2)
Open the front cabinet.
Turn OFF the power switch in the front cabinet of the main unit.
Turn OFF the power switch in the front cabinet of the main unit.
3)
Disconnect the power plug of the main unit from the power out-
let.
let.
4)
Disconnect the connector between the main unit and the sad-
dle finisher.
dle finisher.
B. Installation of the punch unit
1)
Release the lock and separate the saddle finisher from the
main unit.
main unit.
No.
Packed part names
Quantity
1
Harness A (Purple)
1
2
Harness B (Gray)
1
3
Punch jam processing label
1
000-0000
1
2
3
OFF
MX-M503N MX-PNX5A/B/C/D 8 – 2
2)
Remove the screw, and remove the rear cover.
3)
Remove the screw, and remove the front lower cover.
4)
Open the front cover. Remove the screw, and remove the front
inner cover.
inner cover.
5)
Remove the screw, and remove the dummy punch guide.
6)
Install the punch unit to the saddle finisher.
Fix the punch unit with the screw which was removed from the
dummy punch guide.
* Before installing, remove the dust box.
* Check to confirm that the punch guide pin is securely
Fix the punch unit with the screw which was removed from the
dummy punch guide.
* Before installing, remove the dust box.
* Check to confirm that the punch guide pin is securely
inserted into the guide pin insertion hole of the finisher.
* Check to confirm that the pawl (A) is engaged with the plate
frame.
7)
Connect the harness on the punch unit side with the PWB on
the finisher side.
the finisher side.
2
1
A
MX-M503N MX-PNX5A/B/C/D 8 – 3
8)
Fix the front inner cover with screws, and close the front
cover.
cover.
9)
Fix the front lower cover with a screw.
10) Fix the rear cover with a screw.
11) Install the saddle finisher to the main unit.
C. Punch jam processing label attachment
1)
Open the front cover, apply the punch jam processing label
(package part No. 3) in position as shown in the figure.
(package part No. 3) in position as shown in the figure.
D. Punch position label attachment
1)
Attach the label to the position indicated in the figure.
[For scanner]
[For scanner]
1
2
000-0000
Label attachment reference
Second label
Corner R end fitting
Lose the
clearance.
clearance.
First label
Label attachment
reference
Corner of the "upper
Corner of the "upper
cabinet rear"
Corner R end fitting
Click on the first or last page to see other MX-M363N / MX-M363U / MX-M503N / MX-M503U (serv.man18) service manuals if exist.