Sharp MX-M363N / MX-M363U / MX-M503N / MX-M503U (serv.man18) Service Manual ▷ View online
MX-M503N MX-LCX1 3 – 6
3)
Slightly push the tray, restore the stopper to the original posi-
tion, and fix the fixing screw.
tion, and fix the fixing screw.
At that time, check to insure that the stopper pawl is engaged
with the stopper reception of the large capacity tray unit.
with the stopper reception of the large capacity tray unit.
4)
Slowly insert the tray to the original position.
(2) Paper size switch from A4 to B5
Since the factory setting of the paper size is A4, if paper size switch
is required, perform the following procedures.
1)
is required, perform the following procedures.
1)
Slowly pull out the tray until it stops.
2)
Loosen the stopper fixing screw (1 pc) on the right lower side
of the tray so that the stopper does not function.
of the tray so that the stopper does not function.
3)
Pull out the tray again until it stops.
a. Side plate size switch
1)
1)
Remove four fixing screws (blue screws) which are fixing the
upper and the lower sections of the side plate F and the side
plate R.
upper and the lower sections of the side plate F and the side
plate R.
2)
Adjust the mark position of the tray and the side plates in the
lower section of the side plates F/R according to the desired
size. Also adjust the upper section according to the desired
size, and fix with the four fixing screws (blue screws).
lower section of the side plates F/R according to the desired
size. Also adjust the upper section according to the desired
size, and fix with the four fixing screws (blue screws).
F side
R side
MX-M503N MX-LCX1 3 – 7
b. Auxiliary guide size switch
* Since the auxiliary guide setting is not required, fix the auxiliary
* Since the auxiliary guide setting is not required, fix the auxiliary
guide to either of A4 or LT. (To prevent against missing of the
part)
part)
c. Rear edge shaft switch
1)
1)
Remove the rear edge shift fixing screw (blue screw) which is
fixing the shaft to the right side inside the tray, and remove the
rear edge shaft.
fixing the shaft to the right side inside the tray, and remove the
rear edge shaft.
2)
Insert the removed rear edge shaft into the mounting hole in
the paper feed desk as shown in the figure below. Fix the
upper section with the fixing screw (blue screw) which was
removed previously.
the paper feed desk as shown in the figure below. Fix the
upper section with the fixing screw (blue screw) which was
removed previously.
NOTE:
When the rear edge shaft is switched to B5, check to confirm
that the side plates F/R are already set to B5. If the side plates
F/R are not set to B5, the rear edge shaft cannot be switched
to B5.
When the rear edge shaft is switched to B5, check to confirm
that the side plates F/R are already set to B5. If the side plates
F/R are not set to B5, the rear edge shaft cannot be switched
to B5.
3)
Slightly push the tray, restore the stopper to the original posi-
tion, and fix the fixing screw.
tion, and fix the fixing screw.
At that time, check to insure that the stopper pawl is engaged
with the stopper reception of the large capacity tray unit.
with the stopper reception of the large capacity tray unit.
4)
Slowly insert the tray to the original position.
F. Turn on the power of the main unit
1)
Insert the power plug of the main unit into the power outlet.
F side
R side
MX-M503N MX-LCX1 3 – 8
2)
Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit.
Turn ON the power switch in the front cabinet of the main unit.
3)
Turn ON the power switch on the operation panel.
G. Size setting
Execute SIM 26-2 "Size setting" with the key operations of the main
unit.
1)
unit.
1)
The size selection menu of the large capacity tray is displayed
on the operation message display.
on the operation message display.
2)
Select a size button to be set on the message screen.
H. Off-center adjustment
(1) Adjustment with the simulation
Since the off-center adjustment is performed when shipping, there
is basically no need to perform this adjustment. If the center is
shifted, perform the following adjustment procedures.
1)
is basically no need to perform this adjustment. If the center is
shifted, perform the following adjustment procedures.
1)
Enter the SIM50-28 mode.
2)
Select [SETUP/PRINT] ADJ with the key button.
3)
Select [ALL] with the key button.
(Note)
By pressing [LEAD] or [OFFSET] button, the following items
can be executed individually.
* [LEAD]: Print image lead edge image position adjustment
* [OFFSET]: Print image off-center adjustment
By pressing [LEAD] or [OFFSET] button, the following items
can be executed individually.
* [LEAD]: Print image lead edge image position adjustment
* [OFFSET]: Print image off-center adjustment
When [ALL] is selected, both of the above two items are
executed simultaneously.
executed simultaneously.
4)
Select a paper feed tray to be adjusted.
5)
Press [EXECUTE] key.
The adjustment pattern is printed out.
The adjustment pattern is printed out.
6)
Set the adjustment pattern on the document table. (Any direc-
tion)
NOTE: Fit the adjustment pattern correctly with the document
tion)
NOTE: Fit the adjustment pattern correctly with the document
guide.
7)
Press [EXECUTE] key.
The following item is automatically adjustment.
* Print image lead edge image position adjustment
* Print image off-center adjustment
The following item is automatically adjustment.
* Print image lead edge image position adjustment
* Print image off-center adjustment
8)
Press [OK] key.
The adjustment result becomes valid.
The adjustment result becomes valid.
Perform procedures 4) to 7) for each paper feed tray.
(2) Mechanical adjustment
Since the off-center adjustment is performed when shipping, there
is basically no need to perform this adjustment. If the center is
shifted, however, the simulation is normally used. If the shift is not
removed, perform the following adjustment procedures.
1)
is basically no need to perform this adjustment. If the center is
shifted, however, the simulation is normally used. If the shift is not
removed, perform the following adjustment procedures.
1)
Slowly pull out the tray until it stops.
ON
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$872,0$*(326,7,21$'-8670(176(59,&(
2&ǂ$'-
%.0$*ǂ$'-
63)ǂ$'-
6(78335,17ǂ$'-
5(68/7
'$7$
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$872,0$*(326,7,21$'-8670(176(59,&(
/($'
2))6(7
$//
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$872,0$*(326,7,21$'-8670(176(59,&(
(;(&87(
0)7
&6
$'8
&6
&6
&6
/&&
MX-M503N MX-LCX1 3 – 9
2)
Loosen the stopper fixing screw (1 pc) on the right lower side
of the tray so that the stopper does not function.
of the tray so that the stopper does not function.
3)
Pull out the tray again until it stops.
a. When the shift is in the front side
To adjust the print line in the direction A from the paper center as
shown in the figure:
1)
To adjust the print line in the direction A from the paper center as
shown in the figure:
1)
Loosen two fixing screws (red screws) of the front/rear size
guide adjustment plate, and move the size guide adjustment
plate in the direction A (R side) by the shift amount, and tighten
the red fixing screws (2 for each). Move the auxiliary guide in
the direction A by the same size.
guide adjustment plate, and move the size guide adjustment
plate in the direction A (R side) by the shift amount, and tighten
the red fixing screws (2 for each). Move the auxiliary guide in
the direction A by the same size.
Slightly push the tray, restore the stopper to the original posi-
tion, and fix the fixing screw.
Check to insure that the stopper pawl is engaged with the stop-
per reception of the large capacity tray.
tion, and fix the fixing screw.
Check to insure that the stopper pawl is engaged with the stop-
per reception of the large capacity tray.
2)
Slowly insert the tray to the original position.
Then make a copy to check to insure that there is no more
shift. Repeat the procedures until there is no shift.
Then make a copy to check to insure that there is no more
shift. Repeat the procedures until there is no shift.
b. When the shift is in the rear side
To adjust the print line in the direction B from the paper center as
shown in the figure:
1)
To adjust the print line in the direction B from the paper center as
shown in the figure:
1)
Loosen two fixing screws (red screws) of the front/rear size
guide adjustment plate, and move the size guide adjustment
plate in the direction B (F side) by the shift amount, and tighten
the red fixing screws (2 for each). Restore the stopper to the
original position, and fix it with the fixing screws. Move the aux-
iliary guide in the direction B by the same size.
Check to insure that the stopper pawl is engaged with the stop-
per reception of the large capacity tray.
guide adjustment plate, and move the size guide adjustment
plate in the direction B (F side) by the shift amount, and tighten
the red fixing screws (2 for each). Restore the stopper to the
original position, and fix it with the fixing screws. Move the aux-
iliary guide in the direction B by the same size.
Check to insure that the stopper pawl is engaged with the stop-
per reception of the large capacity tray.
2)
Slowly insert the tray to the original position.
Then make a copy to check to insure that there is no more
shift. Repeat the procedures until there is no shift.
Then make a copy to check to insure that there is no more
shift. Repeat the procedures until there is no shift.
A
R side
F side
B
R side
F side
Click on the first or last page to see other MX-M363N / MX-M363U / MX-M503N / MX-M503U (serv.man18) service manuals if exist.