Sharp MX-M363N / MX-M363U / MX-M503N / MX-M503U (serv.man18) Service Manual ▷ View online
MX-M503N MX-DEX8/DEX9 2 – 3
5)
Lift the connection plates on the right and left of the main unit
front side, and fix them with the fixing screws (package part
No. 2).
front side, and fix them with the fixing screws (package part
No. 2).
6)
Replace the No. 3 and No. 2 trays to the original positions.
7)
Lift the connection plates, and fix them with the fixing screws.
8)
Install the connection plate covers.
1
2
2
1
2
1
MX-M503N MX-DEX8/DEX9 2 – 4
D. Release the lock
1)
Pull out each tray.
2)
Turn and remove the fixing material, and remove the caution
sheet.
sheet.
3)
Attach the removed fixing material to the position shown in the
figure for storage.
figure for storage.
4)
Close the cassette which was pulled out.
E. Connector connection
1)
Remove the screw from the back of the main unit. Remove the
connector cover.
connector cover.
2)
Connect the connector.
3)
Split the removed connector cover along the perforated line.
4)
Install the connector cover and fix it with a screw.
NOTE:
Before turning on the power, check to insure that the fixing
material of the tray is disengaged. If the power is turned on
without disengaging the fixing material, a trouble may be
resulted.
Before turning on the power, check to insure that the fixing
material of the tray is disengaged. If the power is turned on
without disengaging the fixing material, a trouble may be
resulted.
MX-M503N MX-DEX8/DEX9 2 – 5
F. Turn on the power of the main unit
1)
Insert the power plug of the main unit into the power outlet.
2)
Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit.
Turn ON the power switch in the front cabinet of the main unit.
3)
Turn ON the power switch on the operation panel.
* For setting the tray size, refer to "Tray size setup" (1-6).
G. Image off-center adjustment
1)
Enter the SIM50-28 mode.
2)
Select [SETUP/PRINT] ADJ with the key button.
3)
Select [ALL] with the key button.
(Note)
By pressing [LEAD] or [OFFSET] button, the following items
can be executed individually.
* [LEAD]: Print image lead edge image position adjustment
* [OFFSET]: Print image off-center adjustment
By pressing [LEAD] or [OFFSET] button, the following items
can be executed individually.
* [LEAD]: Print image lead edge image position adjustment
* [OFFSET]: Print image off-center adjustment
When [ALL] is selected, both of the above two items are
executed simultaneously.
executed simultaneously.
4)
Select a paper feed tray to be adjusted.
5)
Press [EXECUTE] key.
The patch image (adjustment pattern) is printed out.
The patch image (adjustment pattern) is printed out.
6)
Set the adjustment pattern on the document table. (Any direc-
tion)
tion)
NOTE: Fit the adjustment pattern correctly with the document
guide.
7)
Press [EXECUTE] key.
The following item is automatically adjustment.
* Print image lead edge image position adjustment
* Print image off-center adjustment
The following item is automatically adjustment.
* Print image lead edge image position adjustment
* Print image off-center adjustment
8)
Press [OK] key.
The adjustment result becomes valid.
The adjustment result becomes valid.
Perform procedures 4) to 7) for each paper feed tray.
ON
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$872,0$*(326,7,21$'-8670(176(59,&(
2&ǂ$'-
%.0$*ǂ$'-
63)ǂ$'-
6(78335,17ǂ$'-
5(68/7
'$7$
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$872,0$*(326,7,21$'-8670(176(59,&(
/($'
2))6(7
$//
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$872,0$*(326,7,21$'-8670(176(59,&(
(;(&87(
0)7
&6
$'8
&6
&6
&6
/&&
MX-M503N MX-LCX1 3 – 1
MX-M503N
Service Manual
[3] MX-LCX1
1. Unpacking
A. Removal of the large capacity tray unit
B. Removal of the fixing material and packing
parts
1)
Remove the fixing material.
2)
Remove the fixing material and the packing parts.
3)
Remove the paper feed desk fixing screw.
C. Check the packed items
1)
Check that all the items are included in the package.
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
A. Turn off the power of the main unit
1)
Turn OFF the power switch on the operation panel.
No.
Names of bundles
Quantity
1
Mounting plate upper
2
2
Connection unit
1
3
Fixing screw A (Hexagon with seat, S-tight, M4 x 35)
4
4
Fixing screw B (Hexagon with seat, S-tight, M4 x 12)
2
5
Fixing screw C (screw 4 x 8 cup)
1
NOTE:
Before turning on the power, check to insure that the fixing
screw of the tray is removed. If the power is turned on
without removing the fixing screw, a trouble may be
resulted.
Before turning on the power, check to insure that the fixing
screw of the tray is removed. If the power is turned on
without removing the fixing screw, a trouble may be
resulted.
1
3
4
2
5
Click on the first or last page to see other MX-M363N / MX-M363U / MX-M503N / MX-M503U (serv.man18) service manuals if exist.