DOWNLOAD Sharp MX-M350N / MX-M350U / MX-M450N / MX-M450U (serv.man10) Service Manual ↓ Size: 1.03 MB | Pages: 87 in PDF or view online for FREE

MX-M350/M450 N/U  SIMULATION  9 - 29

Since this simulation cannot change the Fax destination, use SIM
66-2 to change the FAX destination.

1) Select START/END of the network scanner trial mode with 10-

key. 

2) Press [START] key.

Max. 500 menus can be scanned.

1) Select YES/NO of the toner save mode with 10-key. 

2) Press [START] key.

1) Select the number corresponding to the operation mode with

10-key.

2) Press [START] key.

(Default: 1 for Europe, 0 for the others)

1) Select the number corresponding to the operation mode with

10-key.

2) Press [START] key.

(Default: 0)

1) Select the number corresponding to the operation mode with

10-key.

2) Press [START] key.

(Default: 0)

9

AB_A

AB series A5

10

CHINA

China

26-10

Setting

Used to set the network scanner trial mode.

Operation

0

END

Trial mode cancel

Default

1

START

Trial mode start

26-18

Setting

Used to set YES/NO of toner save operation. (This 
function is valid only in Japan and UK versions. 
(Depends on the destination setting of SIM26-6.) 
For the other destinations, the same setting can be 
made by the user program P22.)

Specifications

Operation mode

0

YES

Toner save mode is set.

1

NO

Toner save mode is not set.

Default

26-30

Setting

Used to set the operation mode conforming to the 
CE mark (Europe safety standards). (Conforming 
to soft start when driving the fusing heater lamp.)

Specifications

Operation mode (Common)

SIMULATION 26-6

DESTINATION SETUP. SELECT 1-10, AND PRESS START.

1.USA 2.CANADA 3.INCH

4.JAPAN 5.AB_B

6.EUROPE 7.UK 8.AUSTRALIA

9.AB_A   10.CHINA

1

SIMULATION 26-10

NETWORK SCANNER TRIAL SETTING. SELECT 0-1, AND PRESS

START.

0.END

1.START

0

SIMULATION 26-18

TONER SAVE MODE SETTING. SELECT 0-1, AND PRESS START.

0. YES

1. NO

1

0

NO

CE mark control NO (Normal operation)

1

YES

CE mark control YES (Heater lamp soft start 
operation)

26-35

Setting

Used to set whether the same continuous troubles 
are displayed as one trouble or the series of 
troubles with SIM 22-4 when the same troubles 
occur continuously.

Specifications

0

ONCE

When two or more troubles of a same kind occur 
continuously, the troubles are displayed as one 
trouble in the trouble history of SIM22-4. 

1

ANY

When two or more troubles of a same kind occur 
continuously, the troubles are displayed straightly 
as two or more troubles in the trouble history of 
SIM22-4. 

26-38

Setting

Used to set CONTINUE/STOP of printing when 
maintenance timing is over and the count value 
reaches 110% of replacement timing (life). 

Other

Specifications

0

PRINT CONTINUE

Print continue

1

PRINT STOP

Print stop

SIMULATION 26-30

CE MARK CONTROL SETTING. SELECT 0-1, AND PRESS START.

0. NO

1. YES

0

SIMULATION 26-35

TROUBLE MEMORY MODE SETTING. SELECT 0-1, AND PRESS

START.

0. ONCE

1. ANY

0

SIMULATION 26-38

LIFE OVER SETTING. SELECT 0-1, AND PRESS START.

0. PRINT CONTINUE

1. PRINT STOP

0

MX-M350/M450 N/U  SIMULATION  9 - 30

1) Enter the number corresponding to whether AMS operation is

automatically performed or nor in the center binding mode with
the 10-key. 

2) Press [START] key.

(Default: 1 for Europe and UK, 0 for the others)

1) Select ENABLE/DISABLE of the B/W reverse mode with 10-

key.

2) Press [START] key.

1) Select YES/NO of the non-print paper count-up with 10-key.

2) Press [START] key. 

Non-print paper means an insert paper (without copying) in the
OHP insertion mode, a cover (without copying) in the cover inser-
tion mode, back surface, and white paper in the duplex exit mode
(CA, etc.).

(Default: 0 for Japan and Australia, 1 for the other)

The target counters are as follows:

• Copies counter

• Printer counter

• Department management counter

• Total counter

• Effective paper counter

1) Select ENABLE/DISABLE of the CA key cancel function of

print stop with 10-key.

2) Press [START] key.

(Default: 1)

1) Select the number corresponding to the operation mode with

10-key.

2) Press [START] key.

(Default: 0)

26-41

Setting

Used to set the automatic magnification ratio 
selection (AMS) in the pamphlet mode.

Specifications

Operation mode (Common)

0

NO

AMS/APS selection allowed

1

YES

AMS is forcibly operated. 

26-50

Setting

Black-White reverse YES/NO setting (Except for 
UK)

Specifications

Operation

0

DISABLE

B/W reverse mode DISABLE

1

ENABLE

B/W reverse mode ENABLE

Default

26-52

Setting

Used to set whether non-print paper (insertion 
paper, cover paper) (blank image print paper) is 
counted up or not.

Paper transport (Discharge/Switchback/Transport)

Specifications

Operation mode

0

NO (NO COUNT UP)

No count up

1

YES (COUNT UP)

Count up

SIMULATION 26-41

PAMPHLET MODE AMS SETTING. SELECT 0-1, AND PRESS 

START.

0. NO

1. YES

0

SIMULATION 26-50

B/W REVERSE MODE SETTING. SELECT 0-1, AND PRESS 

START.

0. DISABLE

1. ENABLE

1

26-68

Setting

Used to set ENABLE/DISABLE of the CA key 
cancel function of print stop.

Specifications

Operation

0

DISABLE

Disable

1

ENABLE (PRINT STOP)

Enable

27-1

Setting

Used to set the specifications for operations in 
case of communication trouble between the host 
computer and MODEM (machine side). (When 
communication trouble occurs between the host 
computer MODEM and the machine, the self diag 
display (U7-00) is printed and setting for inhibition 
of print or not is made.)

Communication unit (TEL/LIU/MODEM etc.)

Specifications

Operation mode

0

YES

Though a communication trouble occurs between 
the host computer and the MODEM (machine side), 
there is no effect on the machine operations.

1

NO

When a communication trouble occurs between the 
host computer and the MODEM (machine side), the 
self diag display (U7-00) is displayed and printing is 
inhibited.

SIMULATION 26-52

BLANK PAPER COUNT UP SETTING. SELECT 0-1, AND PRESS 

START.

0. NO  (NO COUNT UP)

1. YES (COUNT UP)

1

SIMULATION 26-68

CA KEY CANCEL MODE SETTING. SELECT 0-1, AND PRESS 

START.

0. DISABLE

1. ENABLE (PRINT STOP)

1

SIMULATION 27-1

DISABLING OF U7-00 TROUBLE. SELECT 0-1, AND PRESS START.

0. YES

1. NO

0

MX-M350/M450 N/U  SIMULATION  9 - 31

1) Enter the tag number with 10-key.

2) Press [START] key.

The operating conditions of sensors and detectors are displayed.

The active sensors and detectors are highlighted.

The operating conditions of sensors and detectors are displayed.

The active sensors and detectors are highlighted.

The operating conditions of sensors and detectors are displayed.

The active sensors and detectors are highlighted.

The paper width size detection level is displayed.

27-5

Setting

Used to enter the machine tag No. (This function 
allows to check the tag No. of the machine with the 
host computer.)

Communication unit (TEL/LIU/MODEM etc.)

Specifications

Operation mode

30-1

Operation test/Check

Used to check the operation of sensors and 
detectors in other than the paper feed section and 
the operations of the related circuits.

Operation

PPD1

Resist roller front paper detection 

POD1

After-fusing transport detection 1

POD2

After-fusing transport detection 2

POD3

Paper full detection

DSWL

Cabinet open detection

DSWF

Front door

30-2

Operation test/Check

Used to check the operation of sensors and 
detectors in the paper feed section and the related 
circuits.

Paper feed

Operation

SIMULATION 27-5

TAG # SETTING. INPUT VALUE, AND PRESS START.

PRESENT:  00010000

NEW:      

SIMULATION 30-1

SENSOR CHECK..
PPD1  POD1

POD2  

POD3

DSWL

DSWF

CSS1

Tray 1 insertion detection

PED

Tray 1 paper empty detection 

LUD

Tray 1 upper limit detection 

MCSET

MP unit detection 

MCDRS

MP unit side door open detection 

MCPPD

MP tray transport detection 

MCLUD

MP tray upper limit detection 

MCPED

MP tray paper empty detection 

MCSPD

MP tray remaining quantity detection 

MCSS1

MP tray size detection 1

MCSS2

MP tray size detection 2

MCSS3

MP tray size detection 3

MCSS4

MP tray size detection 4

MP Tray size

(The detection size of MP tray is displayed.)

MPFSET

Manual feed tray detection 

MPED

Manual feed tray paper empty detection 

MPLD

Manual feed length detection 

MPLS1

Manual feed pull-out sensor 1

MPLS2

Manual feed pull-out sensor 2

Bypass Tray size

(The detection size of manual feed tray is 
displayed.)

40-1

Operation test/Check

Used to check the operation of the manual feed 
tray paper size detector and the related circuit. 
(The operation of the manual feed tray paper size 
detector can be monitored with the LCD display.)

Paper feed

Operation

MPLD

Manual tray length detection

MPLS1

Manual tray pull-out detection 1

MPLS2

Manual tray pull-out detection 2

BYPASS_WIDTH

Manual feed guide plate position

BYPASS_AD

Manual feed width detection volume 
output AD value

Bypass Tray width 
size

(Manual tray detection size is displayed.)
A4/A3, 11 x, B5/B4, 8.5 x , A4R, B5R, 
A5R, 5.5x, 7.25x, EXTRA

SIMULATION 30-2

TRAY SENSOR CHECK..

CSS    PED   LUD

MCSET

  MCDRS MCPPD MCLUD MCPED MCSPD MCSS1 MCSS2

MCSS3  MCSS4     (MP Tray size: 

A4

 )

MPFSET

 MPED  MPLD  MPLS1 MPLS2

                 (Bypass Tray size: 

A3

 )

SIMULATION 40-1

BYPASS TRAY SENSOR CHECK..

MPLD

     MPLS1     MPLS2

BYPASS_WIDTH: 

2100

       BYPASS_AD: 

600

(Bypass Tray width size: 

A4/A3

)

MX-M350/M450 N/U  SIMULATION  9 - 32

1) Open the manual paper feed guide to the max. width.

2) Select MAX POSITION with 10-key.

3) Press [START] key.

The max. width detection level is recognized.

4) Press [SYSTEM SETTINGS] key.

5) Set the manual paper feed guide to A4R size width.

6) Select POSITION with 10-key.

7) Press [START] key.

The A4R width detection level is recognized.

8) Press [SYSTEM SETTINGS] key.

9) Set the manual paper feed guide to A5/A5R size width.

10) Select POSITION2 with 10-key.

11) Press [START] key.

The A5R width detection level is recognized.

12) Press [SYSTEM SETTINGS] key.

13) Open the manual paper feed guide to the min. width.

14) Select MIN POSITION with 10-key.

15) Press [START] key.

The min. width detection level is recognized.

If the above procedures are not completed normally, "ERROR" is
displayed. If completed normally, "COMPLETE" is displayed.

1) Select the number corresponding to the set item with 10-key.

2) Press [START] key.

3) Enter the set value with 10-key.

4) Press [START] key.

The operating conditions of sensors and detectors are displayed.

The active sensors and detectors are highlighted.

The paper width detection level is also displayed.

40-2

Adjustment

Used to adjust the manual paper feed tray paper 
width detector detection level.

Paper feed

Operation

Select 4 and press [START] key.

Press [SYSTEM SETTINGS] key.

SIMULATION 40-2

BYPASS TRAY ADJUSTMENT. SELECT 1-4, AND PRESS START.

1. MAX. POSITION

2. POSITION 1

3. POSITION 2

4. MIN. POSITION

1

SIMULATION 40-2

BYPASS TRAY ADJUSTMENT.

MAX. POSITION ··· COMPLETE (or "ERROR")

Press [SYSTEM SETTINGS] key.

SIMULATION 40-2

BYPASS TRAY ADJUSTMENT.

POSITION 1 ··· COMPLETE (or "ERROR")

Select 1 and press [START] key.

SIMULATION 40-2

BYPASS TRAY ADJUSTMENT.

POSITION 2 ··· COMPLETE (or "ERROR")

Press [SYSTEM SETTINGS] key.

Press [SYSTEM SETTINGS] key. 

Select 2 and press [START] key.

Select 3 and press [START] key.

SIMULATION 40-2

BYPASS TRAY ADJUSTMENT.

MIN. POSITION ··· COMPLETE (or "ERROR")

40-7

Adjustment/Setup

Used to enter the manual paper feed tray paper 
width adjustment value.

Paper feed

Operation

1

MAX. POSITION

Max. width

2

POSITION 1

Adjustment point 1

3

POSITION 2

Adjustment point 2

4

MIN. POSITION

Min. value

Press [START] key.

Press [SYSTEM SETTINGS] key.

40-11

Operation test/Check

Used to check the multi-purpose tray width detec-
tion level.

Paper feed

Operation

MCSS1

Tray 3 size detection 1

MCSS2

Tray 3 size detection 2

MCSS3

Tray 3 detection size 3

MCSS4

Tray 3 size detection 4

Multi Purpose 
Tray

(MPT width direction detection size is 
displayed.) A4/A3, 11X, B5/B4, 8.5X, A4R, 
B5R, A5R, 5.5X, 7.25X, EXTRA

SIMULATION 40-7

1

BYPASS TRAY VALUE SETTING. SELECT 1-4, AND PRESS START.

1. MAX. POSITION :   

66

2. POSITION 1  :    

447

3. POSITION 2  :    

704

4. MIN. POSITION :  

916

SIMULATION 40-7

BYPASS TRAY VALUE SETTING. INPUT VALUE 0-1023, AND PRESS

START.

1. MAX. POSITION

66

SIMULATION 40-11

TRAY3 SENSOR CHECK..

MCSS1

     MCSS2     MCSS3     MCSS4

(Multi Purpose Tray width size: 

A4/A3

)