DOWNLOAD Sharp MX-M182 / MX-M182D (serv.man5) Service Manual ↓ Size: 9.62 MB | Pages: 127 in PDF or view online for FREE

MX-M182 SIMULATIONS 7-9

07

01

Used to measure the warm-up time and execute aging with jam detection.
When this simulation is executed, the following warm-up window is displayed.
The time required for starting the warm-up and completing the initializing operation and shifting to the stand-
by state is displayed.
After completion of warm-up, press [CA] key to exit the simulation mode, allowing normal copy operations. 
The copy mode at that time is the aging mode with 0sec of intermittent aging.

Canceled by turning off the power or executing a simulation which makes the hardware reset. When the 
interruption is pressed to shift to the input standby window, the machine does not enter the aging mode. 

06

Used to execute intermittent aging of 3sec. The set quantity and the mode are optionally selected.
When this simulation is executed, the following execution start window is displayed.
When [OK] key or [START] key is pressed, the machine exits the simulation mode.
Enter a desired coy mode and a desired copy quantity.
Press [START] key, and intermittent aging will be started.

It is canceled by turning off the power or executing a simulation with the hard reset.

08

Used to measure the warm-up time.
When this simulation is executed, the following warm-up window is displayed.
The time required for starting the warm-up and completing the initializing operation and shifting to the stand-
by state is displayed.
*

Though [CA] key is  pressed, the machine does not enter the aging mode of intermission 0 sec.

Press [CA] key to exit the simulation mode.
(The aging function is omitted from SIM 07-01.)
Note: Toner supply operation is not performed during this simulation.

08

01

Used to check the developing bias output.
When this simulation is executed, the following execution start window is displayed.
When [OK] key or [START] key is pressed, the developing bias signal is turned ON for 30sec. When 
measuring the actual output value, however, use SIM 25-01.
After completion of the process, the machine returns to the sub code input window.

[CA] key: Exits the simulation mode.
[INTERRUPT] key: Interrupts output operation and shifts to the sib code input window. 

Main 
code

Sub 

code

Contents

Remark

Sim7-1 W-UP C-MODE

WARMING UP.

[CA] key

1

(Warming up window)

Sim7-1 W-UP C-MODE

WARM UP COMPLETED.

10

(Warming up completion window)

Ready to copy.

S

100%

8 1/2×11

(Copy window)

Sim7-6  INTERVAL SET

AER YOU SURE? EXEC

AGING INTERVAL

(Execution start window)

Ready to copy.

S

100%

8 1/2×11

(Copy window)

Sim7-8 W-UP C-MODE
WARMING UP.

1

(Warming up window)

Sim7-8 W-UP C-MODE

WARM UP COMPLETED.

10

(Warming up completion window)

Sim8-1    DV BIAS

PRESS OK KEY EXEC

Sim8-1    DV BIAS

EXEC

[OK] key or [START] Key

(Execution start window)

(Execution window)

MX-M182 SIMULATIONS 7-10

08

02

Used to check the main charger output.
When this simulation is executed, the following execution start window is displayed.
When [OK] key or [START] key is pressed, the main charger is turned on for 30 sec in the grid voltage HIGH 
mode.
After completion of the process, the machine returns to the sub code input window.

[CA] key: Exits the simulation mode.
[INTERRUPT] key: Interrupts output operation and shifts to the sub code input window. 

03

Used to check the main charger output.
When this simulation is executed, the following execution start window is displayed.
When [OK] key or [START] key is pressed, the main charger is turned on for 30 sec in the grid voltage LOW 
mode.
After completion of the process, the machine returns to the sub code input window.

[CA] key: Exits the simulation mode.
[INTERRUPT] key: Interrupts output operation and shifts to the sub code input window.

06

When this simulation is executed, the machine shifts to the following mode select window, and the list of the 
modes to be outputted is displayed.
Select an output mode with numeric keys and press [OK] key or [START] key, and the transfer charger 
output is made for about 30sec in the specified mode.

*

The items of (back) is not displayed when DUPLEX setting is OFF.

*

Small size paper is Letter R (A4R) width or below. When an output is completed, the machine shifts to 

the mode select window. 

[CA] key: Exits the simulation mode.
[INTERRUPT] key: Interrupts the output operation, and shifts to the sub code input window.

Main 
code

Sub 

code

Contents

Remark

Sim8-2    MHV(H)

PRESS OK KEY EXEC

Sim8-2    MHV(H)

EXEC

[OK] key or [START] Key

(Execution start window)

(Execution window)

Sim8-3    MHV(L)

PRESS OK KEY EXEC

Sim8-3    MHV(L)

EXEC

[OK] key or [START] Key

(Execution start window)

(Execution window)

Sim8-6 TC OUTPUT
1:NML_A
2:NML_B
3:SML_A

4:SML_B
5:BYPASS

2

(Mode selection window)

Sim8-6 TC OUTPUT
1:NML_A
2:

NML_B

3:SML_A

4:SML_B
5:BYPASS

2

EXEC

(Execution window)

[OK] key or [START] Key

EXEC

Window display

 Output mode

1:NML_A

 Normal size width (front)

2:NML_B

 Normal size width (back)

3:SML_A

 Small size width (front)

4:SML_B

 Small size width (back)

MX-M182 SIMULATIONS 7-11

09

01

Duplex motor forward rotation check
Used to check the duplex motor rotation.
The duplex motor is rotated in the normal direction (paper exit direction) for 30sec.
After completion of the process, the machine shifts to the sub code input window.

[CA] key: Exits the simulation mode.
[INTERRUPT] key: Interrupts the output operation, and shifts to the sub code input window.

(Execution is not 
allowed when 
DUPLEX setting is 
OFF.)

02

Used to check the duplex motor reverse rotation.
The duplex motor is rotated in the reverse direction for 30sec.
After completion of the process, the machine shifts to the sub code input window.

[CA] key: Exits the simulation mode.
[INTERRUPT] key: Interrupts the output operation, and shifts to the sub code input window.

(Execution is not 
allowed when 
DUPLEX setting is 
OFF.)

04

Used to adjust the duplex motor rotation speed.
When this simulation is executed, the following setting window is displayed. Enter an input value with 
numeric keys and press [OK] key or [START] key.
The setting range is in 1-13 steps.

When a value outside the setting range is inputted, it is ignored.
[CA] key: Exits the simulation mode.
[INTERRUPT] key: Shift to the sub code input window.

Default:
4

05

Used to adjust the duplex motor switchback time when the motor reverse rotation is controlled.
When this simulation is executed, the following setting window is displayed. Enter an input value with 
numeric keys and press [OK] key or [START] key.
The setting range is 50-76.
When the adjustment value is increased by 1, the distance up to reverse start is increased by 3 steps in 1-2 
phase excitement.

When a value outside the setting range is inputted, it is ignored.
[CA] key: Exits the simulation mode.
[INTERRUPT] key: Shift to the sub code input window.

Default:
50

Main 
code

Sub 

code

Contents

Remark

Sim9-1    DMF CHECK

PRESS OK KEY EXEC

Sim9-1    DMF CHECK

EXEC

[OK] key or [START] Key

(Execution start window)

(Execution window)

Sim9-2    DMR CHECK

PRESS OK KEY EXEC

Sim9-2    DMR CHECK

EXEC

[OK] key or [START] Key

(Execution start window)

(Execution window)

Sim9-4  MOTOR SPEED

4

4

[    1-13]

1:MOTOR SPEED

(Setting window)

• 18cpm/20cpm machine:

Set value  : Speed (PPS)
01 

: 637.2PPS (Slow)

02 : 

640.4PPS

03 : 

643.6PPS

04 : 

646.9PPS

05 : 

650.1PPS

06 : 

653.3PPS

07 : 

656.5PPS

08 : 

659.8PPS

09 : 

662.9PPS

10 : 

666.2PPS

11 : 

669.4PPS

12 : 

672.6PPS

• 23cpm machine:

Set value  : Speed (PPS)
01 

: 760.2PPS (Slow)

02 : 

764.1PPS

03 : 

768.0PPS

04 : 

771.8PPS

05 : 

775.7PPS

06 : 

779.5PPS

07 : 

783.3PPS

08 : 

787.2PPS

09 : 

791.0PPS

10 : 

794.8PPS

11 : 

798.6PPS

12 : 

802.5PPS

Sim9-5  SW BACK TIME

50

50

[   50-76]

1:SW BACK TIME

MX-M182 SIMULATIONS 7-12

10

-

Used to check the operation of the toner motor.
When this simulation is executed, the following execution start window is displayed. Press [OK] key or 
[START] key, and the toner motor is rotated for about 30sec.
After completion of the process, the machine shifts to the sub code input window.

[CA] key: Exits the simulation mode.
[INTERRUPT] key: Interrupts the output operation, and shifts to the sub code input window.

14

-

* Used to cancel EEPROM writing troubles such as H trouble and execute the hard reset.
When this simulation is executed, the following execution start window is displayed. Press [OK] key or 
[START] key to clear the trouble other than U2.

16

-

*

Used to cancel the U2 trouble and execute the hard reset.

When this simulation is executed, the following execution start window is displayed. Press [OK] key or 
[START] key to clear the U2 trouble.

20

01

Used to clear the maintenance counter.
Press [OK] key or [START] key on the following window, the maintenance counter is cleared and the 
machine returns to the sub code input window.

21

01

Used to set the maintenance cycle. When this simulation is executed, the current set value is displayed. 
Enter a desired code with numeric keys and press [START] key. The set value is saved in the EEPROM and 
the machine returns to the sub code input window.

[CA] key: Exits the simulation mode.
[INTERRUPT] key: Returns to the sub code input window.

Default:
4

Main 
code

Sub 

code

Contents

Remark

Sim10  TONER MOTOR

PRESS OK KEY EXEC

Sim10  TONER MOTOR

EXEC

[OK] key or [START] Key

(Execution start window)

(Execution window)

Sim14 TROUBLE CLEAR

AER YOU SURE? EXEC

TROUBLE CLEAR
(WITHOUT U2)

(Execution start window)

Sim16  TROUBLE CLEAR

AER YOU SURE? EXEC

U2 TROUBLE CLEAR

(Execution start window)

Sim20-1 COUNTER CLR

AER YOU SURE? EXEC

MAINTENANCE COUNTER
CLEAR

Sim21-1 CYCLE SET.

4

4

[    0-  5]

1:MAINTE CYCLE

0: 5K (5,000 sheets)
1: 7.5K (7,500 sheets)
2: 10K (10,000 sheets)
3: 25K (25,000 sheets)
4: 50K (50,000 sheets)
5: FREE (999,999 sheets)
(Setting range: 0 - 5)