Sharp MX-M182 / MX-M182D (serv.man5) Service Manual ▷ View online
MX-M182 SIMULATIONS 7-13
22
01
Counters display
Though SIM26-74 is set to "1: Scan counter is added," the count is not added to SIM22-01 total counter
display. The setting affects only the total counter display in the system settings.
display. The setting affects only the total counter display in the system settings.
03
Jam memory display
Used to check the jam kind occurred in the main unit and the SPF/RSPF.
The kinds of jams up to 30 items are displayed sequentially from the latest one. (The oldest one is deleted
sequentially.) This display is used for troubleshooting. (If there are extremely many troubles in a position, it
may be judged that a repair must be executed.)
The kinds and contents of jams to be displayed are as follows.
The kinds of jams up to 30 items are displayed sequentially from the latest one. (The oldest one is deleted
sequentially.) This display is used for troubleshooting. (If there are extremely many troubles in a position, it
may be judged that a repair must be executed.)
The kinds and contents of jams to be displayed are as follows.
[CA] key: Exits the simulation mode.
[INTERRUPT] key: Shifts to the sub code input window.
[INTERRUPT] key: Shifts to the sub code input window.
key, key: Switches to another page.
04
Jam total counter display
Used to display the jam total counter.
Main
code
code
Sub
code
Contents
Remark
Sim22-1 COUNTER 1/4
TOTAL :nnnnnnn
MAINTE :nnnnnnn
DEV :nnnnnnn(*)
DRUM :nnnnnnn
MAINTE :nnnnnnn
DEV :nnnnnnn(*)
DRUM :nnnnnnn
Sim22-1 COUNTER 2/4
key
key
CPY JOB : nnnnnnn
PRT JOB : nnnnnnn
SCN JOB : nnnnnnn
OC SCN
PRT JOB : nnnnnnn
SCN JOB : nnnnnnn
OC SCN
: nnnnnnn
Sim22-1 COUNTER 3/4
SPF :
nnnnnnn
DUPLEX :
nnnnnnn
OTHERS : nnnnnnn
MNTCYC : nnnnnnn
MNTCYC : nnnnnnn
Sim22-1 COUNTER 4/4
DEV TTL : nnnnnnn
DRM TTL : nnnnnnn
DRM TTL : nnnnnnn
Counter display
TOTAL :
TOTAL :
Total
counter
MAINTE : Maintenance counter
DEV
DEV
: Development counter
DRUM
: Drum counter
CPY JOB : Copy job counter
PRT JOB : Print job counter
SCN JOB : Scan job counter
OC SCN : OC scan counter
SPF
PRT JOB : Print job counter
SCN JOB : Scan job counter
OC SCN : OC scan counter
SPF
: SPF/RSPF counter
DUPLEX : DUPLEX counter
OTHERS : Other counter
MNTCYC : Maintenance cycle
DEV TTL : Development rotation accumulated time
DRM TTL : Drum rotation accumulated time
OTHERS : Other counter
MNTCYC : Maintenance cycle
DEV TTL : Development rotation accumulated time
DRM TTL : Drum rotation accumulated time
key
key
key
key
Sim22-3 JAM HIS. 1/4
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
Sim22-3 JAM HIS. 2/4
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
Kinds of jams and display contents
SPPD_ON : SPF paper entry sensor (Not reached)
SPPD_OFF : SPF paper entry sensor (Remaining)
SOUT_ON : SPF paper exit sensor (Not reached)
SOUT_OFF : SPF paper exit sensor (Remaining)
POUT_ON : Paper exit sensor (Not reached)
POUT_OFF : Paper exit sensor (Remaining)
DPX_ON
SPPD_ON : SPF paper entry sensor (Not reached)
SPPD_OFF : SPF paper entry sensor (Remaining)
SOUT_ON : SPF paper exit sensor (Not reached)
SOUT_OFF : SPF paper exit sensor (Remaining)
POUT_ON : Paper exit sensor (Not reached)
POUT_OFF : Paper exit sensor (Remaining)
DPX_ON
: DUP sensor (Not reached)
DPX_OFF
: DUP sensor (Remaining)
PIN_ON
: Paper feed sensor (Not reached)
PIN_OFF
: Paper feed sensor (Remaining)
PIN2_ON
: Cassette 2 paper feed sensor (Not reached)
PIN3_ON
: Cassette 3 paper feed sensor (Not reached)
PIN4_ON
: Cassette 4 paper feed sensor (Not reached)
key
key
Sim22-4 COUNTER
JAM : nnnnnn
MX-M182 SIMULATIONS 7-14
22
07
System setting code display
Used to display the system setting code.
09
Paper feed counter display
Used to display the paper feed quantity of each paper feed tray. This simulation shows the use frequency of
each paper feed section.
each paper feed section.
[CA] key: Exits the simulation mode.
[INTERRUPT] key: Shifts to the sub code input window.
[INTERRUPT] key: Shifts to the sub code input window.
key, key: Switches to another page.
*
TRAY2-TRAY4 are displayed only when they are installed.
11
FAX-related counter display.
Used to display the current FAX send/receive counter value.
13
CRUM destination display
Used to display the CRUM chip destination code saved in the EEPROM. If the display does not match the
destination code saved in the CRUM chip, it is judged as an error.
*
destination code saved in the CRUM chip, it is judged as an error.
*
This simulation is valid only for the model with the CRUM chip.
14
P-ROM version display
The version of the option board which is not installed is not displayed.
Main
code
code
Sub
code
Contents
Remark
Sim22-7 SYSTEM
SYS CODE:
nnnnn
Sim22-9 COUNTER 1/2
BYPASS :
nnnnnnn
TRAY1 :
nnnnnnn
TRAY2 :
nnnnnnn
TRAY3 :
nnnnnnn
Sim22-9 COUNTER 2/2
TRAY4 :
nnnnnnn
key
key
Sim22-11 FAX COUN.
COMM. PAGE
SND xx, xxx, xxx
RCV xx, xxx, xxx
SND xx, xxx, xxx
RCV xx, xxx, xxx
Sim22-11 FAX COUN.
SELECT COUNTER
3:PRINT PAGE
3:PRINT PAGE
(1 - 3)
Sim22-11 FAX COUN.
COMM. TIME
SND:hhhhhhhh:mm:ss
RCV:hhhhhhhh:mm:ss
SND:hhhhhhhh:mm:ss
RCV:hhhhhhhh:mm:ss
Sim22-11 FAX COUN.
SELECT COUNTER
1:COMM. PAGE
2:COMM. TIME
(1 - 3)
1:COMM. PAGE
2:COMM. TIME
(1 - 3)
Sim22-11 FAX COUN.
PRINT PAGE
xxxxxxxx
xxxxxxxx
[1] key
[OK] key
[OK] key
[OK] key
[2] key
[3] key
Return
Return
[CA] key
: Simulation cancel
[INTERRUPT] key
: Sub code input window
Sim22-13 CRUM
CRUM TYPE nn
Number : Setting (Destination)
00
00
: Not set.
01
: Destination-A (North America)
02
: Destination-B (Europe)
03
: Destination-C (SMEF)
04 :
CHN-A
05 :
JPN-A
Number : Setting (Destination)
06
06
: Destination-X (Iran)
99 :
Conversion
Sim22-14 ROM VER1/2
S/N :
-----------
MCU :
--.--
NNB :
--.--
PNL :
--.--
Sim22-14 ROM VER2/2
FAX :
--.--
S/N
:Production serial number
MCU :Main unit program version
NNB
NNB
:NNB program version
PNL
:Panel program version
FAX
:FAX program version
MX-M182 SIMULATIONS 7-15
22
15
Trouble memory display
The latest 20 troubles are displayed. (The oldest one is overwritten sequentially.)
[CA] key: Exits the simulation mode.
[INTERRUPT] key: Shifts to the sub code input window.
[INTERRUPT] key: Shifts to the sub code input window.
key, key: Switches to another page.
The display sequence is as shown below.
In this case, (1) is the latest one and (12) is the oldest.
22
SPF/RSPF jam counter display
Used to display the SPF/RSPF JAM counter.
When [INTERRUPT] key is pressed, the machine goes to the sub code input window. When [CA] key is
pressed, the machine exits the simulation mode.
When [INTERRUPT] key is pressed, the machine goes to the sub code input window. When [CA] key is
pressed, the machine exits the simulation mode.
(Only when the
SPF/RSPF is
installed.)
SPF/RSPF is
installed.)
24
01
Jam total counter clear
When this simulation is executed, the clear confirmation window is displayed as shown below.
When [OK] key or [START] key is pressed, the jam total count and the jam memory are cleared and the
machine shifts to the sub code input window.
When [OK] key or [START] key is pressed, the jam total count and the jam memory are cleared and the
machine shifts to the sub code input window.
02
Trouble memory clear
Used to clear the trouble memory and the trouble history data in the EEPROM.
When [INTERRUPT] key is pressed, the machine shifts to the sub code input window. When [CA] key is
pressed, the machine exits the simulation mode.
When [INTERRUPT] key is pressed, the machine shifts to the sub code input window. When [CA] key is
pressed, the machine exits the simulation mode.
(Only when the
SPF/RSPF is
installed.)
SPF/RSPF is
installed.)
04
SPF/RSPF counter clear
Used to clear the SPF/RSPF paper feed counter.
[CA] key: Exits the simulation mode.
[INTERRUPT] key: Shifts to the sub code input window.
[INTERRUPT] key: Shifts to the sub code input window.
Main
code
code
Sub
code
Contents
Remark
Sim22-15 TROUBLE 1/2
Sim22-15 TROUBLE 2/2
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
XX-XX XX-XX
XX-XX XX-XX XX-XX
XX-XX XX-XX
key
key
Sim22-15 TROUBLE 1/2
1
2
3
4
2
3
4
5
6
7
8
6
7
8
9
10
11
12
Sim22-22 JAM CNT
SPF :
nnnnnnn
Sim24-1 COUNTER CLR
AER YOU SURE? EXEC
JAM COUNTER CLEAR
Sim24-2 COUNTER CLR
AER YOU SURE? EXEC
TROUBLE COUNTER
CLEAR
CLEAR
Sim24-4 COUNTER CLR
AER YOU SURE? EXEC
SPF COUNTER
CLEAR
CLEAR
MX-M182 SIMULATIONS 7-16
24
05
Duplex print counter clear
Used to clear the duplex print counter.
[CA] key: Exits the simulation mode.
[INTERRUPT] key: Shifts to the sub code input window.
[INTERRUPT] key: Shifts to the sub code input window.
(Execution is not
allowed when
DUPLEX setting is
OFF.)
allowed when
DUPLEX setting is
OFF.)
06
Paper feed counter clear
Used to clear the paper feed counter data in each paper feed section.
*
TRAY2-TRAY4 are displayed only when they are installed.
[CA] key: Exits the simulation mode.
[INTERRUPT] key: Shifts to the sub code input window.
[INTERRUPT] key: Shifts to the sub code input window.
07
Drum counter clear
Used to clear the drum counter and the drum rotating time.
[CA] key: Exits the simulation mode.
[INTERRUPT] key: Shifts to the sub code input window.
[INTERRUPT] key: Shifts to the sub code input window.
08
Copy counter clear
Used to clear the copy counter.
[OK] key or [START] key: Clears the copy counter and shifts to the sub code input window.
[CA] key: Exits the simulation mode.
[INTERRUPT] key: Shifts to the sub code input window.
[CA] key: Exits the simulation mode.
[INTERRUPT] key: Shifts to the sub code input window.
09
Printer counter clear
Used to clear the printer counter and other counters.
Select a counter to be cleared and press [OK] key or [START] key. The confirmation window is displayed.
Press [OK] key or [START] key again, and the specified counter is cleared and the machine returns to the
initial window.
Select a counter to be cleared and press [OK] key or [START] key. The confirmation window is displayed.
Press [OK] key or [START] key again, and the specified counter is cleared and the machine returns to the
initial window.
[CA] key: Exits the simulation mode.
[INTERRUPT] key: Shifts to the sub code input window.
[INTERRUPT] key: Shifts to the sub code input window.
Main
code
code
Sub
code
Contents
Remark
Sim24-5 COUNTER CLR
AER YOU SURE? EXEC
DUPLEX COUNTER
CLEAR
CLEAR
Sim24-6 COUNTER CLR
Sim24-6 COUNTER CLR
Sim24-6 COUNTER CLR
Numeric
Key
Key
1:BYPASS
2:TRAY1
3:TRAY2
2:TRAY1
3:TRAY2
4:TRAY3
5:TRAY4
5:TRAY4
0
1:BYPASS
2:TRAY1
3:TRAY2
2:TRAY1
3:TRAY2
4:TRAY3
5:TRAY4
5:TRAY4
2
1:BYPASS
2:TRAY1
3:TRAY2
ARE YOU SURE?
2:TRAY1
3:TRAY2
ARE YOU SURE?
4:TRAY3
5:TRAY4
5:TRAY4
2
[C] Key
[OK] key or
[START] key
[OK] key or
[START] key
Return
(Initial window)
(Counter selection window)
(Confirmation window)
Sim24-7 COUNTER CLR
AER YOU SURE? EXEC
DRUM COUNTER
CLEAR
CLEAR
Sim24-8 COUNTER CLR
AER YOU SURE? EXEC
COPIES COUNTER
CLEAR
CLEAR
Sim24-9 COUNTER CLR
Sim24-9 COUNTER CLR
1:PRINT
2:OTHER
2:OTHER
[OK] key or
[START] key
[START] key
[OK] key or [START] key (Counter clear)
[BACK] key
Numeric key input
1
1:PRINT
2:OTHER
1
ARE YOU SURE?
Click on the first or last page to see other MX-M182 / MX-M182D (serv.man5) service manuals if exist.