Sharp MX-M160 / MX-M160D / MX-M160DK (serv.man4) Service Manual ▷ View online
AR-SP10/AR-RP10 4 - 1
[4] AR-SP10/AR-RP10
1. Unpacking
For unpacking, refer to the figure below.
2. Installation
Turn the main switch of the copier to the “OFF” position and then
remove the power plug of the copier from the outlet.
remove the power plug of the copier from the outlet.
1) Remove the document cover.
Lift the document cover from the copier and tilt it to the rear side to
remove it.
remove it.
2) Remove the right cabinet.
Remove the screws and remove the right cabinet.
3) Remove the document glass and the right document glass holder.
Remove the screws, remove the document glass from the copier, and
then remove the right document glass holder.
then remove the right document glass holder.
4) Attach the SPF glass holder.
Fit the SPF glass holder to the document glass.
Attach the document glass to the copier and fix it with the screws.
AR-SP10/AR-RP10 4 - 2
5) Attach the right cabinet.
Reattach the right cabinet to its original position and fix it with the
screws.
screws.
6) Cut out the cut-out portion.
Cut out the cut-out portion of the rear cabinet with nippers or the like.
At this time, be careful about the orientation of the nippers so that the
cut plane of the rear cabinet is flat.
cut plane of the rear cabinet is flat.
7) Attach the automatic document feeder.
Insert the hinge portions of the document feeder into the mounting por-
tions of the copier by holding the feeder at an angle toward the rear
side.
tions of the copier by holding the feeder at an angle toward the rear
side.
8) Connect the relay connector.
Connect the harness of the automatic document feeder to the connec-
tor of the copier and tighten the screws on the connector.
tor of the copier and tighten the screws on the connector.
9) Remove the filament tape.
Remove the filament tape located in the positions shown in the illustra-
tion.
tion.
AR-D34/AR-D35 5 - 1
[5] AR-D34/AR-D35
1. Unpacking
(AR-D34)
(AR-D35)
2. Installation
Included parts
1) Remove the document cover.
Lift the document cover from the copier and tilt it to the rear side to
remove it.
remove it.
2) Remove the rear cabinet.
Remove the screw and remove the cover. Then, remove the five screws
and remove the rear cabinet.
and remove the rear cabinet.
Part name
Quantity
Screw M4 x 12 (Fixing plate)
8
Screw M4 x 10
2
Fixing plate
4
Paper size label
1
AR-D34/AR-D35 5 - 2
3) Remove the copier rear cover.
Remove the two screws and remove the rear cover.
4) Make a hole for connector.
• Copier (1-tray model)
Cut out the portion shown in the illustration with nippers or the like.
• Copier (2-tray model)
Press the portion shown in the illustration with a screwdriver or the
like to remove it.
like to remove it.
5) Remove the second cassette rear cover.
Remove the rear cover which is attached to the 250-sheet paper feed
unit.
unit.
Remove the rear cover (upper stage) from the 500-sheet paper feed
unit.
unit.
6) Install the copier onto the 250-sheet paper feed unit.
Put the copier on the 250-sheet paper feed unit, and fix with the fixing
plates and the screws.
plates and the screws.
Use the small fixed plate for front side of the machine.
• Copier (1-tray model) + 250-sheet paper feed unit
• Copier (2-tray model) + 250-sheet paper feed unit
Click on the first or last page to see other MX-M160 / MX-M160D / MX-M160DK (serv.man4) service manuals if exist.