DOWNLOAD Sharp MX-M160 / MX-M160D / MX-M160DK (serv.man4) Service Manual ↓ Size: 3.36 MB | Pages: 38 in PDF or view online for FREE

MX-FX10  6 - 3

9) Paste label on the rear cabinet of the copier.

 

After installing FAX Expansion Kit, paste the supplied label on the 
position shown in the illustration.

10) Setup date and time.

 

Press [FUNCTION] key on the Operation Panel, select [Key 
Operator Program], enter 5-digit key operator code, and select 
[FAX] mode.

 

Select [Initial setup] and then [Date and Time]. Enter date in the 
order of year, Month, Day and press [OK] to set.

 

Select [Time Setup], enter time in the order of Hour and Minute, and 
press [OK] to set.

11) Clear image memory.

* When additional memory board (AR-MM9) is installed, you must 

clear the memory using the Simulation [66-10]. If no additional 
memory is installed, there is no need for this memory clear process.

12) Connect line cable.

Connect the line cable to the FAX Expansion Kit.

Even when connecting the telephone line to TEL line, attach the core to 
the telephone line.

USA, Canada only
In order to manifest the compliance with FCC Part 68 and IC CS-03, it 
is required to provide the machine with the FCC Registration Number 
(USA), Ringer Equivalence (USA) and Ringer Eqivalence(Canada).
After installing the FAX expansion kit in the machine, please put the 
registration label, packed with the kit, on the prescribed location.

Australia, New Zealand only
A-TICK label attachment.

Insert the power plug of the copier to the outlet, and then turn on the 
main switch of the copier.

200V Series Only

MX-NB10  7 - 1

1) Cut out three cut-out portions from the rear cabinet using a cutter or 

the like.

2) Use a Phillips screwdriver or the like to open a hole.

Connect the connector of the network expansion kit to the connector of 
the main unit and put excessive harness into the cut-out portion in the 
main unit.

Engage the two pawls on the rear of the network expansion kit with the 
cut-out portions of the main unit and network expansion kit using the 
supplied screw (3 x 14).

1) Attach the supplied cable clamp to the position shown in the illustra-

tion.

2) Connect the USB cable to the network expansion kit and the main 

unit. At this time, reduce slack of the cable with the cable clamp as 
shown in the illustration.

3) Connect the network cable.

Phillips screwdriver

Screw (M3x14)

Connector

Pawl

Pawl

MX-NB10  7 - 2

Before installing the printer driver, be sure to set the IP address of the 
machine as explained in “System Settings” in the “Network Printer” 
manual on the CD-ROM. Consult your network administrator for the 
correct IP address, subnet mask, and default gateway to be entered. If 
a DHCP server will automatically assign an IP address to the machine, 
the following procedure is not necessary. (To check the IP address 
assigned to the machine by DHCP, see “2-2. CHECKING THE IP 
ADDRESS”.)

Caution: If the machine is used in a DHCP environment, the machine's 

IP address may change automatically. If this happens, printing 
will no longer be possible. In this event, use a WINS server or 
do not use the machine in a DHCP environment.

There are several settings where the IP address must be entered or 
checked.

 

To check the IP address of the machine, hold down the status button on 
the network expansion kit at least 2 seconds to print out a Printer Set-
ting List.

Caution: How to reset the network expansion kit

To reset the network expansion kit, power on the machine 
while holding down the status button on the network expansion 
kit.

 

Network scanner destination information and scanning set-
tings will remain after the network expansion kit is reset, how-
ever, the network settings and network printer settings will 
revert to the factory default settings.

Status 
button

MX-TR10  8 - 1

• For improvement of workability, some description in this manual as 

well as components and accessories may change without prior 
notice.In this case, refer to the service manual.

1) Open the document cover or the document feeder.

2) Open the bypass tray.

3) Remove the right door.

4) Open the front cover

5) Remove the five screws and then remove the right cabinet.

6) Remove the screw and then remove the right front cabinet.

1) Connect the connector.

2) Insert the two bosses of the copier into the positioning holes of the 

separator motor unit and secure it with the supplied screw.

1) Insert the excessive cord into the clamp attached on the separator 

motor unit and arrange the wiring as shown in the illustration.

1) Rotate the separator gear to move the lever to the position shown in 

the illustration. Do not move the lever position until operation check 
is performed.

Turn off the main switch of the copier and then remove the power plug 
of the copier from the outlet.