Sharp MX-M160 / MX-M160D / MX-M160DK (serv.man4) Service Manual ▷ View online
MX-M160D CONFIGURATION 2 - 1
[2] CONFIGURATION
1. System Configurations
2. Machine configuration
[MX-M200D]
[MX-M160D]
[MX-M160]
(250-sheet paper
feed unit)
feed unit)
(2 x 250-sheet paper
feed unit)
feed unit)
[AR-RP10]
[AR-D35]
[AR-D34]
[MX-TR10]
AR-RP10
(REVERSING SINGLE PASS FEEDER)
[AR-SP10]
[AR-VR7]
[MX-NB10]
(SINGLE PASS FEEDER)
(DOCUMENT COVER)
(JOB SEPARATOR)
[MX-FX10]
(FACSIMILE
EXPANSION KIT)
EXPANSION KIT)
(NEWORK PRINTING /
SCANNING
EXPANSION KIT)
SCANNING
EXPANSION KIT)
Standard for North America only
MX-M200D
MX-M160D
MX-M160
Copy
STD
STD
STD
Color scanner
STD
STD
STD
SPLC printer
STD
STD
STD
PCL printer
OPT
OPT
OPT
Fax
OPT
OPT
OPT
Network
OPT
OPT
OPT
Duplex
STD
STD
N/A
Sort
STD
STD
STD
Paper tray
2-stage
1-stage
1-stage
MX-M160D CONFIGURATION 2 - 2
3. Option list
O: Option installation enable X: Option installation disable
Model name
Name
MX-M200D
MX-M160D
MX-M160
Product key
target
AR-RP10
REVERSING SINGLE PASS FEEDER
North/South America: STD
Europe, Australia, Agency: OPT
Europe, Australia, Agency: OPT
OPT
N/A
—
AR-SP10
SINGLE PASS FEEDER
North/South America: N/A
Europe, Australia, Agency: OPT
Europe, Australia, Agency: OPT
OPT
OPT
—
AR-VR7
DOCUMENT COVER
North/South America:N/A
Europe, Australia, Agency: OPT
Europe, Australia, Agency: OPT
OPT
STD
—
AR-D34
250-SHEET PAPER FEED UNIT
OPT
OPT
OPT
—
AR-D35
2X250-SHEET PAPER FEED UNIT
OPT
OPT
OPT
—
MX-TR10
JOB SEPARATOR TRAY KIT
OPT
OPT
OPT
—
MX-NB10
N E W O R K P R I N T I N G / S C A N N I N G
EXPANSION KIT
EXPANSION KIT
OPT
OPT
OPT
—
MX-FX10
FACSIMILE EXPANSION KIT
OPT
OPT
OPT
—
AR-SM5
256MB EXPANTION MEMORY BOARD
OPT
OPT
OPT
—
AR-MM9
FAX EXPANTION MEMORY BOARD
OPT
OPT
OPT
—
AR-PF1
BARCODE FONT KIT
OPT
OPT
OPT
—
MX-PK10
PS3 EXPANSION KIT
OPT
OPT
OPT
Yes
AR-PF2
MACRO FONT FLASH ROM KIT
OPT
OPT
OPT
—
MX-M200D/MX-M160D/MX-M160 3 - 1
[3] MX-M200D/MX-M160D/MX-M160
1.Installing conditions
A.Copier installation
Do not install your copier in areas that are:
•damp, humid, or very dusty
•exposed to direct sunlight
•poorly ventilated
•subject to extreme temperature or humidity changes, e.g., near an air
•damp, humid, or very dusty
•exposed to direct sunlight
•poorly ventilated
•subject to extreme temperature or humidity changes, e.g., near an air
conditioner or heater.
•Be sure to allow the required space around the machine for servicing
and proper ventilation.
B.Power source
•Use an exclusive to dedicated power outlet. If the power plug of this
machine is inserted into a power outlet commonly used with other
illumination units, flickers of the lamp may be result. Use a power outlet
which is not used commonly with any illumination units.
illumination units, flickers of the lamp may be result. Use a power outlet
which is not used commonly with any illumination units.
•Avoid complex wiring.
C.Grounding wire connection.
•To avoid danger, the power outlet must be grounded. If no grounding
wire is connected and a leakage occurs, a fire or an electric shock may
be result.
be result.
2. Removal of protective material and fixing
screw
1) Remove all tapes and protective material.
•Remove all tapes, then open the document cover and remove the
•Remove all tapes, then open the document cover and remove the
protective material of sheet shape
2) Remove the fixing screw.
•Use a coin to remove the fixing screw.
•The fixing screw is required when transporting the machine. Keep it in
•Use a coin to remove the fixing screw.
•The fixing screw is required when transporting the machine. Keep it in
the tray. (Refer to the later description.)
3.Installing procedure
A.Developer cartridge installation
1) Open the bypass tray, and open the side cover.
2) Open the front cover.
•Hold the both sides and pull down to open.
2) Open the front cover.
•Hold the both sides and pull down to open.
3) Loosen the screw and remove the developer cartridge.
4) Remove the developer tank from the developer cartridge.
5) Shake the developer bag enough before opening it, and supply the
developer into the developer tank.
• While rotating the MG roller in the arrow direction, supply the
developer into the developer tank evenly so as not to overflow.
MG roller
MX-M200D/MX-M160D/MX-M160 3 - 2
6) Check that two hooks of the developer unit is hooked on the toner
cartridge guide, and secure the toner cartridge guide to the
developing unit.
developing unit.
*
Check that the DV seal is free from the developer. If developer is
attached to the DV seal, clean it.
attached to the DV seal, clean it.
*
After supplying developer, do not tilt or shake the developer
cartridge.
cartridge.
7) Attach the developer cartridge to the main unit, and secure it with
the screw.
B.Toner cartridge installation
1) Remove the new toner cartridge from the bag. Grasp the cartridge
on both sides and shake it horizontally four or five times.
2) Insert the toner cartridge along the guides until it locks in place while
pushing the lock release lever
•If there is any dirt or dust on the toner cartridge, remove it before
installing the cartridge..
C. Set the toner density reference control level
1) With the front cover open, turn ON the machine power and enter
SIM25-02.
Note: When the machine is not in the simulation mode, if the front
cover is closed and the machine power is turned ON, toner
may be supplied from the toner cartridge to the developer
cartridge.
Under this state, the toner density reference control level
adjustment cannot be made properly.
Therefore, if the front cover is closed and the machine power
is turned ON with the machine not in the simulation mode,
dispose developer and supply new developer and adjust the
toner density reference level.
may be supplied from the toner cartridge to the developer
cartridge.
Under this state, the toner density reference control level
adjustment cannot be made properly.
Therefore, if the front cover is closed and the machine power
is turned ON with the machine not in the simulation mode,
dispose developer and supply new developer and adjust the
toner density reference level.
2) Close the front cabinet.
3) Press [START] key, and execute SIM25-02.
Note: It takes about 3 minutes to execute SIM25-02 completely.
Note: It takes about 3 minutes to execute SIM25-02 completely.
During execution of this simulation, the front cover must not be
opened and the machine power must not be turned OFF.
opened and the machine power must not be turned OFF.
4. Removal and storage of fixing screw
1) Lift the knob and gently pull out the tray.
2) Hold the paper pressure plate and turn the fixing screw in the arrow
direction.
3) Store the fixing pin and the fixing screw in the tray.
•Store the fixing screw which was removed in the above procedure 2 and
•Store the fixing screw which was removed in the above procedure 2 and
the fixing screw which was removed in procedure 2 of 2.
•Removal of protective material and fixing screw in the storage place in
the tray.
hook
4 or 5 times
Screw
fixing
pin
Click on the first or last page to see other MX-M160 / MX-M160D / MX-M160DK (serv.man4) service manuals if exist.