Sharp MX-M160 / MX-M160D / MX-M160DK (serv.man4) Service Manual ▷ View online
AR-D34/AR-D35 5 - 3
• Copier (1-tray model) + 500-sheet paper feed unit
• Copier (2-tray model) + 500-sheet paper feed unit
7) Remove the connection gear lock.
Remove the connection gear lock (with the red tug) after setting.
8) Connect the connector
Connect the optional relay harness contained in the 1-tray model (2-tray
model) paper feed unit to the PWB of the copier.
model) paper feed unit to the PWB of the copier.
• Optional relay harness
• Copier (1-tray model) + 250-sheet paper feed unit
AR-D34/AR-D35 5 - 4
• Copier (2-tray model) + 250-sheet paper feed unit
• Copier (1-tray model) + 500-sheet paper feed unit
• Copier (2-tray model) + 500-sheet paper feed unit
9) Remove the cassette packing fixtures.
Pull the cassette until it stops.
Turn and remove the packing lock fixture which is fixing the paper pres-
sure plate inside the cassette in the direction of arrow.
sure plate inside the cassette in the direction of arrow.
MX-FX10 6 - 1
[6] MX-FX10/AR-MM9
1. Unpacking
<Before installation>
• For improvement of workability, some description in this manual as
well as components and accessories may change without prior notice.
In this case, refer to the service manual.
2. Installation
1) Detach the rear cover.
<1>Unscrew two screws from the rear cover.
<2>Push to release the lock shown in the illustration below. Slide to
<1>Unscrew two screws from the rear cover.
<2>Push to release the lock shown in the illustration below. Slide to
right and remove the rear cover.
2) Work the rear cover.
Cut and remove the cut-out portion from the rear cover using a tool
such as nippers. Be careful with the tool's direction so that the cut
surface would be flat.
such as nippers. Be careful with the tool's direction so that the cut
surface would be flat.
* If no need to install, go on to Step 3 to continue FAX Expansion Kit
Installation.
Insert an additional memory board into the socket of FAX Expansion
Unit. Be careful with the inserting direction. Make sure that it is securely
inserted.
Unit. Be careful with the inserting direction. Make sure that it is securely
inserted.
3) Install FAX Expansion Unit.
<1>Hook the attaching parts of FAX Expansion Unit (two on the right)
<1>Hook the attaching parts of FAX Expansion Unit (two on the right)
onto the copier frame as shown.
<2>Hook the attaching part of FAX Expansion Unit (one on the left)
onto the copier frame as shown.
<3>Push the lower left side of the unit to make sure that connectors of
FAX Expansion Unit and the copier are connected.
<4>Secure the unit onto the copier using four supplied screws (S tight)
as shown.<1>Hook the attaching parts of FAX Expansion Unit (two
on the right) onto the copier frame as shown.
on the right) onto the copier frame as shown.
Turn off the main switch of the copier and then remove the power plug
of the copier from the outlet.
of the copier from the outlet.
Parts included
FAX Expansion Unit: 1
FAX keyboard: 1
Core: 2
(200V series only)
(200V series only)
FCC label : 1
(USA, Canada only)
(USA, Canada only)
Operation manual: 1
line cable: 1
Screws (S tight): 4
Writing label: 4
A-TICK label: 1
(Australia,
New Zealand only)
(Australia,
New Zealand only)
Line Adapter: 1
(Australia/New Zealand
/Hong Kong only)
/Hong Kong only)
Installing additional memory board (AR-MM9)
MX-FX10 6 - 2
4) Reattach the rear cover.
<1>Insert the claw locks of the rear cover into the copier, and slide it to
<1>Insert the claw locks of the rear cover into the copier, and slide it to
left until they are securely locked.
<2>Secure the cover using two screws.
5) Remove keyboard back cover.
<1>Unscrew two screws from the keyboard back cover.
<2>Release the lock as shown, and remove the back cover.
<1>Unscrew two screws from the keyboard back cover.
<2>Release the lock as shown, and remove the back cover.
6) Remove dummy panel.
<1>Unscrew from the dummy panel.
<2>Disengage the pawls, and remove it from the copier.
<1>Unscrew from the dummy panel.
<2>Disengage the pawls, and remove it from the copier.
7) Attach FAX keyboard.
<1>Connect the copier flat cable to FAX keyboard.
<2>Place the FAX keyboard onto the copier while engaging the pawls.
<3>Secure the keyboard using a screw.
<1>Connect the copier flat cable to FAX keyboard.
<2>Place the FAX keyboard onto the copier while engaging the pawls.
<3>Secure the keyboard using a screw.
8) Reattach keyboard back cover.
<1>Insert the claw lock of the keyboard back cover into the copier.
<1>Insert the claw lock of the keyboard back cover into the copier.
Make sure that the claw lock is securely inserted.
<2>Secure the cover using two screws.
Click on the first or last page to see other MX-M160 / MX-M160D / MX-M160DK (serv.man4) service manuals if exist.