DOWNLOAD Sharp MX-M160 / MX-M160D / MX-M160DK (serv.man4) Service Manual ↓ Size: 3.36 MB | Pages: 38 in PDF or view online for FREE

MX-TR10  8 - 2

1) Attach the paper holder arm on the back side of the separator tray.

 

At this time, be careful about the orientation of the paper holder 
arm.

1) Insert the rib on the back side of the separator tray into the groove 

of the copier and place the tray in the copier as shown in the illustra-
tion.

Note: Do not remove the paper holder arm that has been attached in 

the copier.

2) Attach the bosses on the rear and front sides of the separator tray 

to the separator levers on the rear and front sides of the copier.

1) Taking care that the projection (indicated with 

) of the separator 

tray pin is up, push the separator tray pin until it clicks.

1) Reattach the right front cabinet to its orginal position and secure it 

with the screw M4 x 10.

2) Reattach the right cabinet to its orginal position and secure it with 

the screw M3 x 6 and the four screws M3 x 8.

3) Close the front cover.

4) Reattach the right door and close it.

5) Close the bypass tray.

6) Close the document cover or the document feeder.

MX-TR10  8 - 3

1) Use the keys on the copier to execute simulation [26-1-1].

2) Press the [CA] key to exit the simulation.

1) Use the keys on the copier to execute simulation [3-4].

2) The separator tray will move up and down and then stop automati-

cally after simulation is complete.

Note: Step-out noise may be caused only at initial operation but it is not 

a malfunction.

3) Press the [CA] key to exit the simulation.

CHANGING THE COPY PAPER SIZE IN THE TRAY 9 - 1

If the size of the loaded paper is different from the size shown in the 
display, follow the steps below to change the paper size setting of the 
tray.

Note:

•  The paper size setting cannot be changed during copying, printing, 

fax printing (when the fax option is installed), or interrupt copying, or 
when a misfeed has occurred. However, if the machine is out of 
paper or out of toner, the paper size setting can be changed during 
copying, printing, and fax printing.

•  See "[3] SPECIFICATIONS" on the Service Manual (00ZMXM200D 

S1E) for information on the specifications for the types and sizes of 
paper that can be loaded in the paper trays.

•  The paper size cannot be set for the bypass tray.

 

1) Adjust the plates in the tray to the length and width of the paper.

•  The plate A is a slide-type guide. Grasp the locking knob on the 

guide and slide the guide to the indicator line of the paper to be 
loaded.

•  The plate B is an insert-type guide. Remove it and then insert it at 

the indicator line of the paper to be loaded.

•  When using 11" x 17" sized paper store the plate B in the slot at the 

left front of the paper tray.

2) Press the [SPECIAL FUNCTION] key.

3) Press the [ ] or [ ] key to select "PAPER SIZE SET".

4) Press the [OK] key.

5) Press the [ ] or [ ] key to select the paper tray for which the paper 

size is being changed.

6) Press the [ ] key.

The cursor moves to the paper size selection position on the right.

7) Press the [ ] or [ ] key to select the paper size.

To change the size of another paper tray, press the [ ] key and then 
repeat steps 5 to 7.

8) Press the [OK] key.

A message asking you to confirm the new paper size setting will 
appear.

9) Press the [OK] key.

The selected paper size will be stored and the display will return to 
the base screen.

Note:Affix the paper size label for the paper size selected in step 7 to the 

label position on the right end of the tray.

Plate B

Plate A

The special function 
screen will appear.

EXPOSURE
COLOR MODE

PAPE

RESOLUT

COPY
SCAN

SPECIAL

FUNCTION

LINE

DATA

DATA

ON LINE

 SPECIAL FUNCTION
  

SPECIAL MODES

  ORIG. SIZE ENTER
  PAPER SIZE SET
  DISPLAY CONTRAST

PQ

ACC

LEX SCAN
LEX SCAN

UPLEX

 SPECIAL FUNCTION
  SPECIAL MODES
  ORIG. SIZE ENTER
  

PAPER SIZE SET

  DISPLAY CONTRAST

The paper size setting 
screen will appear.

GHI

PQRS

BACK

OK

AN

X

 PAPER SIZE SET
   

8 x11R

    11x17

   11x17     8 x14
             8 x13
             8 x11

1

2

1

2

1

2

1

2

Example: Tray 2

 PAPER SIZE SET
   8 x11    11x17
   

11x17 

   8 x14

            8 x13
            8 x11

1

2

1

2

1

2

1

2

 PAPER SIZE SET
   8 x11     

11x17

   11x17     8 x14
             8 x13
             8 x11

1

2

1

2

1

2

1

2

Example: Selecting 8-1/2" x 

14" size

 PAPER SIZE SET
   8 x11     11x17
   11x17     

8 x14

             8 x13
             8 x11

1

2

1

2

1

2

1

2

OK

ADJUSTMENTS 10 - 1

Simulation is hereinafter described as SIM.

Perform the following procedure to enter the SIM mode.
"#" key 

 Interrupt key 

 "C" key 

 Interrupt key 

 Main code 

Start key 

 Sub code 

 Start key

When the clear all key is pressed, the SIM mode is cancelled.
When the interruption key is pressed, the process is interrupted and the 
screen returns to the sub code entering display.
*

After canceling the SIM mode, be sure to turn OFF/ON the power 
and check the operation.

Note:If the machine is terminated by a jam error or paper empty during 

copying in the adjustment by the SIM, recopying is required.

Note: If a jam error or paper empty occurs during copying in the 

adjustment by the simulation, the image data are not saved, and 
therefore recopying is required.

Note:In advance to this adjustment, the sub scanning magnification ratio 

adjustment must be performed.

1) Set a scale on the OC table as shown below.

2) Make a copy.
3) Check the copy output. If necessary, perform the following 

adjustment procedures.

4) Execute SIM 50-1.
5) Set the OC lead edge position set value (PHOTO indicator ON) to [1]

 

The OC image scanning start position is shifted inside the document 
edge.

6) Set the 1st tray lead edge void adjustment value (TEXT indicator 

ON) * to [1]

 

The lead edge void becomes the minimum.

7) Set the 1st tray print start position value (AUTO, 1st tray indicator 

ON) to [1] and make a copy.

 

The print start position is shifted inside the document edge.

8) Measure the image loss R of the copied image. Enter the set value 

of the image scanning lead edge position (PHOTO indicator ON) 
again.

•1 step of the set value corresponds to about 0.1mm shift.
•Calculate the set value from the formula below.
R/0.1(mm) = Image loss set value

 

 <R: Image loss measurement value (mm)>

Example:

4/0.1 = 40 = about 40

Note:If the set value is not obtained from the above formula, perform the 

fine adjustment.

5

10

5mm

4mm

*

The dimension varies depending on the model.

10

5mm

0mm

5

*

 The scanning edge is set. 

   (A line may be printed by scanning the document edge.)