Sharp MX-B201D (serv.man9) Service Manual ▷ View online
MX-B201/B201D SIMULATION, TROUBLE CODES 10 - 26
:'11/Oct/17
1
46
39
FAX mode sharpness
adjustment
(When MX-FX12 is installed)
adjustment
(When MX-FX12 is installed)
[Function]
When [START] key is pressed, scan is started with the entered sharpness adjustment value,
and the data of the selected mode stored on the FAX side is changed to the entered value.
When [START] key is pressed, scan is started with the entered sharpness adjustment value,
and the data of the selected mode stored on the FAX side is changed to the entered value.
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
1
Sharpness adjustment value data table
When initializing each data: 1
Mode
Sharpness adjustment value
1: STD
2: FINE
3: S-FINE
4: FINE/PHOTO
5: S-FINE/PHOTO
2: FINE
3: S-FINE
4: FINE/PHOTO
5: S-FINE/PHOTO
1) Initial display
2) [
] [
] key or after 2sec
Every time when [
] key is pressed,
the second line is changed in the
sequence of No. 1
sequence of No. 1
→ 2 → 3 → 4 → 5 →
1.
When [
] key is pressed, the sequence
is reversed.
3) Select the arrow key 1-5, and the LED of
[START] key is lighted.
("ZZZZ" is the mode selected among STD,
FINE, S-FINE, FINE/PHOTO, and S-FINE/
PHOTO.)
FINE, S-FINE, FINE/PHOTO, and S-FINE/
PHOTO.)
("X" is the corresponding sharpness adjust-
ment value of the selected mode stored on
the FAX side.)
ment value of the selected mode stored on
the FAX side.)
* [Clear] key: Returns to “2)” display.
4) Enter a one-digit value (0-2) as the sharp-
ness adjustment value with [Numeric]
key.
key.
("Y" is the entered sharpness adjustment
value.)
value.)
* [Clear] key: Returns to “2)” display.
5) Scan start (self print)
6) Print start (self print)
After completion of printing, returns to “4)”
display.
display.
SHARPNESS SETTING
PRESS
←
,
→
SHARPNESS SET (1-5)
1:STD
SHARPNESS SETTING
ZZZZ(0-2) X
SHARPNESS SETTING
ZZZZ(0-2) Y
SHARPNESS SETTING
SCAN Y
SHARPNESS SETTING
PRINT Y
MX-B201/B201D SIMULATION, TROUBLE CODES 10 - 27
48
01
Front/rear (main scanning)
direction and scan (sub
scanning) direction
magnification ratio
adjustment
direction and scan (sub
scanning) direction
magnification ratio
adjustment
[Function]
Used to adjust the magnification ratio in the main scan (front/rear) direction and sub scan direc-
tion.
Used to adjust the magnification ratio in the main scan (front/rear) direction and sub scan direc-
tion.
Enter the adjustment value with [Numeric] key. Press [START] key to save the set value and
make a copy. (When the adjustment value is increased by 1, the magnification ratio is increased
by 0.1%.)
make a copy. (When the adjustment value is increased by 1, the magnification ratio is increased
by 0.1%.)
The adjustment mode can be changed by pressing [
] [
] key.
(Adjustment range: 1 – 99, Default: 50)
[Operation]
The operation is similar to simulation 46-01.
The operation is similar to simulation 46-01.
05
RSPF mode sub scan
direction magnification ratio
in copying
direction magnification ratio
in copying
[Function]
Used to display the current RSPF mode sub scan direction magnification ratio on the LCD/dis-
play.
Used to display the current RSPF mode sub scan direction magnification ratio on the LCD/dis-
play.
When [START] key is pressed, the entered data is acquired and saved into the EEPROM, and a
copy is made. (When the set value is increased by 1, the magnification ratio is increased by
0.1%.)
copy is made. (When the set value is increased by 1, the magnification ratio is increased by
0.1%.)
The adjustment mode can be changed by pressing [
] [
] key. (Adjustment range: 1 – 99,
Default: 50)
When adjusting the RSPF, the mode is set to "Duplex
→
Single," single copies of two sheets are
performed.
For printing, regardless of the density mode and the density level,
Density mode = MANUAL
Density level = 3
Density level = 3
* When there is no document in RSPF, copy is inhibited.
[Operation]
The operation is similar to simulation 46-01.
The operation is similar to simulation 46-01.
Main
code
code
Sub
code
Contents
Details of function/operation
Mode
Display item
LED
Default
Main scan direction magnification ratio
F-R
PRINT mode lamp
50
OC mode sub scan direction
magnification ratio
magnification ratio
SCAN
SCAN mode lamp
50
Mode
Initial value of
duplex setting
duplex setting
Display item
LED
Default
Sub scan magnification ratio
adjustment on the front surface of
RSPF document
adjustment on the front surface of
RSPF document
S-S
SIDE1
COPY mode
lamp
lamp
50
Sub scan magnification ratio
adjustment on the back surface of
RSPF document
adjustment on the back surface of
RSPF document
D-S
SIDE2
PRINT mode
lamp
lamp
50
MX-B201/B201D SIMULATION, TROUBLE CODES 10 - 28
49
01
MCU Download mode
[Function]
When this simulation is executed, "DOWNLOAD MODE" is displayed on the LCD, the machine
goes into the program writing mode from PC to Flash ROM.
When this simulation is executed, "DOWNLOAD MODE" is displayed on the LCD, the machine
goes into the program writing mode from PC to Flash ROM.
Use the writing tool on the PC and write the program.
During writing, the display shows as follows:
After completion of download, turn OFF/ON the power to reset.
In case of an error in download, the following message is displayed on the LCD.
To enter the download mode, there is a method to use key operations as well as to use a simu-
lation. With the power OFF, press and hold [Clear All] key + [
lation. With the power OFF, press and hold [Clear All] key + [
] key, turn on the power.
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
Status
Display item
Remark
Download data receiving
RECEIVING
Loader function transfer
LOADER COPYING
Date delete start
FLASH ERASE
Data write (Boot section)
BOOT WRITING
Data write (Program section)
PROGRAM WRITING
Data write (EEPROM)
E2PROM WRITING
Data write (LCD)
LCD DATE WRITING
During SUM CHECK
FLASH ROM SUM CHECK
During BOOT SUM CHECK
BOOT SUM CHECK
During EEPROM SUM CHECK
EEPROM SUM CHECK
Download complete
DOWNLOAD COMPLETE!
Error status
Display item
PC data receiving
E-01 PC TRANS
Loader function transfer
E-02 LOADER COPY
FLASH ROM delete
E-03 FLASH ERASE
Boot section FLASH ROM write
E-04 BOOT WRITE
Program section FLASH ROM write
E-05 PROGRAM WRITE
Loader section SUM CHECK
E-06 LOADER SUM
Boot section SUM CHECK
E-07 BOOT SUM
Program section SUM CHECK
E-08 PROGRAM SUM
E2PROM SUM CHECK
E-09 E2PROM SUM
E2PROM write
E-10 E2PROM WRITE
E2PROM read Verify
E-11 E2PROM READ
E2PROM collating Verify
E-12 E2PROM COLLATE
Boot section lens check
E-13 BOOT LENGTH
Program section lens check
E-14 PROGRAM LENGTH
E2PROM lens check
E-15 E2PROM LENGTH
Total data size check
E-16 DATE SIZE
Network board communication error
E-17 ANB TRANS
Network board FRASH ROM write
E-18 ANB FLASH WRITE
LCD section lens check
E-19 LCD DATE LENGTH
LCD section FLASH ROM write
E-20 LCD DATE WRITE
LCD section SUM CHECK
E-21 LCD DATE SUM
1) Initial display
DOWNLOAD MODE
MX-B201/B201D SIMULATION, TROUBLE CODES 10 - 29
49
02
ANB Download mode
[Function]
When this simulation is executed, the machine enters the wiring mode of the program from the
USB memory.
The status display is as shown below.
When this simulation is executed, the machine enters the wiring mode of the program from the
USB memory.
The status display is as shown below.
The program is written from the USB memory.
During writing, the LED indicates as shown below.
After completion of download, turn OFF/ON the power to reset.
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
<LCD panel model>
* During execution of this simulation, only ANB downloading can be operated.
Status
LCD display
Start process
PREPARE READ SCRIPT
NO SCRIPT FILE
BEGIN SPF UPDATE
BEGIN SPF UPDATE
BEGIN LOADER UPDATE
END LOADER UPDATE
Data write (Firmware)
BEGIN FW UPDATE
Data write end (Firmware)
END FW UPDATE
Data write (WEB)
BEGIN WEB UPDATE
Data write end (WEB)
END WEB UPDATE
End process
END SPF UPDATE
READ SCRIPT FILE END
1) Initial display (The current version is shown in XX:XX:XX.)
2) Download completion display
ANB DOWNLOAD MODE
ANB PROG:XX:XX:XX
DOWNLOAD MODE
DOWNLOAD COMPLETE!
Click on the first or last page to see other MX-B201D (serv.man9) service manuals if exist.