Sharp MX-B201D (serv.man9) Service Manual ▷ View online
MX-B201/B201D SIMULATION, TROUBLE CODES 10 - 22
46
13
Density adjustment in the
FAX mode (Normal text)
(When MX-FX12 is installed)
FAX mode (Normal text)
(When MX-FX12 is installed)
[Function]
Scan is started with the exposure adjustment value entered with [START] key, and the stored
data of the selected mode on the FAX side is rewritten into the input value.
Scan is started with the exposure adjustment value entered with [START] key, and the stored
data of the selected mode on the FAX side is rewritten into the input value.
[Operation]
14
Density adjustment in the
FAX mode (Fine text)
(When MX-FX12 is installed)
FAX mode (Fine text)
(When MX-FX12 is installed)
[Function]
When [START] key is pressed, scan is started with the entered exposure adjustment value and
the data of the selected mode on the FAX side is changed to the entered value.
When [START] key is pressed, scan is started with the entered exposure adjustment value and
the data of the selected mode on the FAX side is changed to the entered value.
For the density adjustment value table data, refer to SIM46-13 (FAX mode density adjustment
(Normal text).)
(Normal text).)
[Operation]
15
Density adjustment in the
FAX mode (Super fine)
(When MX-FX12 is installed)
FAX mode (Super fine)
(When MX-FX12 is installed)
[Function]
When [START] key is pressed, scan is started with the entered exposure adjustment value and
the data of the selected mode on the FAX side is changed to the entered value.
When [START] key is pressed, scan is started with the entered exposure adjustment value and
the data of the selected mode on the FAX side is changed to the entered value.
For the density adjustment value table data, refer to SIM46-13 (FAX mode density adjustment
(Normal text).)
(Normal text).)
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
1
Density adjustment value data table
When initializing each data: 50
Mode
Photo
Exposure adjustment value
STD (Normal text)
off
Fine (Fine text)
on
off
off
Sfine (Super fine)
on
off
off
1) Initial display
("XX" is the corresponding exposure adjust-
ment value of normal text mode stored on the
FAX side.)
ment value of normal text mode stored on the
FAX side.)
2) Enter a 2-digit value as the exposure
adjustment value with [Numeric] key.
("YY" is the entered exposure adjustment
value.)
value.)
3) Scan is started (self print), and the LED
of [START] key is turned off.
4) Print is started (self print).
After completion of printing, returns to “2)”
display.
display.
ADJUST EXP. STD
XX
ADJUST EXP. STD
YY
ADJUST EXP. STD
SCAN YY
ADJUST EXP. STD
PRINT YY
1) Initial display
("XX" is the corresponding exposure adjust-
ment value of the fine text mode stored on
the FAX side.)
ment value of the fine text mode stored on
the FAX side.)
2) Enter a 2-digit value as the exposure
adjustment value with [Numeric] key.
("YY" is the entered exposure adjustment
value.)
value.)
3) Scan start (self print)
4) Print start (self print)
After completion of printing, returns to “2)”
display.
display.
ADJUST EXP. FINE
XX
ADJUST EXP. FINE
YY
ADJUST EXP. FINE
SCAN YY
ADJUST EXP. AUTO
PRINT YY
1) Initial display
("XX" is the corresponding exposure adjust-
ment value of the super fine mode stored on
the FAX side.)
ment value of the super fine mode stored on
the FAX side.)
2) Enter a 2-digit value as the exposure
adjustment value with [Numeric] key.
("YY" is the entered exposure adjustment
value.)
value.)
3) Scan start (self print)
4) Print start (self print)
After completion of printing, returns to “2)”
display.
display.
ADJUST EXP. S-FINE
XX
ADJUST EXP. S-FINE
YY
ADJUST EXP. S-FINE
SCAN YY
ADJUST EXP. S-FINE
PRINT YY
：'11/Oct/17
1
MX-B201/B201D SIMULATION, TROUBLE CODES 10 - 23
46
18
Image contrast adjustment
(300dpi)
(300dpi)
[Function]
Contrast is set for each mode.
When this simulation is executed, the current se value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to make a copy under the set value.
When the set value is increased, the contrast becomes higher. When the set value is
decreased, the contrast becomes lower.
In this case, only Exp.3 copy is made. When, however, the setting is made to make higher con-
trast, Exp.1 and Exp.5 copies also become in higher contrast. When made to a lower contrast,
Exp1. and Exp.5 copies become lower contrast, too.
Press [
Contrast is set for each mode.
When this simulation is executed, the current se value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to make a copy under the set value.
When the set value is increased, the contrast becomes higher. When the set value is
decreased, the contrast becomes lower.
In this case, only Exp.3 copy is made. When, however, the setting is made to make higher con-
trast, Exp.1 and Exp.5 copies also become in higher contrast. When made to a lower contrast,
Exp1. and Exp.5 copies become lower contrast, too.
Press [
] [
] key to switch the mode. The set value of the selected mode is displayed on
the LCD/display.
(Adjustment value: 1 – 99)
(Adjustment value: 1 – 99)
* No density display on LCD/display.
[Operation]
The operation is similar to simulation 46-01.
The operation is similar to simulation 46-01.
19
Exposure mode setup
[Function]
<
<
γ
table setting>
When this simulation is executed, the code number of the current set gamma table is displayed.
(Default: 2)
Enter the code number corresponding to the desired gamma table, and press [
(Default: 2)
Enter the code number corresponding to the desired gamma table, and press [
] [
] key to
change the mode and write into the EEPROM.
<AE operation mode>
When setting the
γ
table, press [
] key to change to the AE operation mode, and the current
set code number of the AE operation mode is displayed. (Default: 0)
Enter the code number corresponding to the desired AE operation mode and press [
Enter the code number corresponding to the desired AE operation mode and press [
] [
]
key to change the mode and write into the EEPROM.
<PHOTO image process setting>
When [
] key is pressed in AE operation mode setting, the mode is changed to the PHOTO
image process setting and the code number of the current set PHOTO image process setting is
displayed. (Default: 1)
Enter the code number corresponding to the desired PHOTO image process setting and press
[
displayed. (Default: 1)
Enter the code number corresponding to the desired PHOTO image process setting and press
[
] [
] key to change the mode and write into the EEPROM.
[Operation]
The operation is similar to simulation 43-01.
The operation is similar to simulation 43-01.
Main
code
code
Sub
code
Contents
Details of function/operation
Mode
Display item
LED
Default
AE mode (300dpi)
AE
COPY mode lamp
50
TEXT mode (300dpi)
TEXT
PRINT mode lamp
50
PHOTO mode
PHOTO
SCAN mode lamp
50
TS mode (TEXT) (300dpi)
TSTXT
PRINT mode lamp
SCAN mode lamp
SCAN mode lamp
50
TS mode (AE) (300dpi)
TSAE
COPY mode lamp
SCAN mode lamp
SCAN mode lamp
50
Dither mode
D_PHO
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
PRINT mode lamp
SCAN mode lamp
50
Mode
Display item
Code number
Setting content
Remark
γ
GAMMA
1
Image quality priority mode
2
Toner consumption priority mode
Default
AE
AE
0
Lead edge stop
Default
1
Real time process
PHOTO
PHOTO
1
Error diffusion process
Default
2
Dither process
MX-B201/B201D SIMULATION, TROUBLE CODES 10 - 24
46
20
RSPF exposure correction
[Function]
Used to adjust the exposure correction amount in the RSPF mode. The adjustment is made by
adjusting Vref voltage variation for the OC mode.
Used to adjust the exposure correction amount in the RSPF mode. The adjustment is made by
adjusting Vref voltage variation for the OC mode.
When this simulation is executed, the current set value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to save the setting and make a copy.
Change the set value and press [START] key to save the setting and make a copy.
When the set value is increased, copy becomes darker. When the set value is decreased, copy
becomes lighter. (Adjustment range: 1 – 99)
becomes lighter. (Adjustment range: 1 – 99)
[Operation]
The operation is similar to simulation 46-01.
The operation is similar to simulation 46-01.
29
Image contrast adjustment
(600dpi)
(600dpi)
[Function]
Contrast is set for each mode.
Contrast is set for each mode.
When this simulation is executed, the current se value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to make a copy under the set value.
When the set value is increased, the contrast becomes higher. When the set value is
decreased, the contrast becomes lower.
decreased, the contrast becomes lower.
In this case, only Exp.3 copy is made. When, however, the setting is made to make higher con-
trast, Exp.1 and Exp.5 copies also become in higher contrast. When made to a lower contrast,
Exp1. and Exp.5 copies become lower contrast, too.
trast, Exp.1 and Exp.5 copies also become in higher contrast. When made to a lower contrast,
Exp1. and Exp.5 copies become lower contrast, too.
Press [
] [
] key to switch the mode. The set value of the selected mode is displayed on
the LCD/display. (Adjustment value: 1 – 99)
* No density display on LCD/display.
[Operation]
The operation is similar to simulation 46-01.
The operation is similar to simulation 46-01.
30
AE limit adjustment
[Function]
Used to set the limit value in AE and AE (toner save).
Change the setting and press [ENTER]/[START] key to write the setting into the EEPROM. The
machine goes into the sub code entry standby mode.
By pressing [
Used to set the limit value in AE and AE (toner save).
Change the setting and press [ENTER]/[START] key to write the setting into the EEPROM. The
machine goes into the sub code entry standby mode.
By pressing [
] [
] key, setting is changed. (Setting range: 0 - 255, Default 196)
<Remark>
When simulation 26-06 (Destination setting) or simulation 46-19 Auto Exposure mode is
changed, the setting of this simulation is also changed to the default in connection.
changed, the setting of this simulation is also changed to the default in connection.
[Operation]
The operation is similar to simulation 46-19.
The operation is similar to simulation 46-19.
Main
code
code
Sub
code
Contents
Details of function/operation
Mode
Display item
Default
Remark
RSPF
SPF
50
Mode
Display item
LED
Default
AE mode (600dpi)
AE
COPY mode lamp
50
TEXT mode (600dpi)
TEXT
PRINT mode lamp
50
PHOTO mode
PHOTO
SCAN mode lamp
50
TS mode (TEXT) (600dpi)
TSTXT
PRINT mode lamp
SCAN mode lamp
SCAN mode lamp
50
TS mode (AE) (600dpi)
TSAE
COPY mode lamp
SCAN mode lamp
SCAN mode lamp
50
Dither mode
D_PHO
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
PRINT mode lamp
SCAN mode lamp
50
Mode
Display item
Remark
Limit value for AE
AE
Limit value for AE (Toner save)
TSAE
Limit value for AE (SPF)
AESPF
Limit value for AE (Toner save), (SPF)
TAESPF
MX-B201/B201D SIMULATION, TROUBLE CODES 10 - 25
46
31
Image sharpness
adjustment
adjustment
[Function]
Used to adjust sharpening/blurring of image in each mode.
Used to adjust sharpening/blurring of image in each mode.
When this simulation is executed, warm-up and shading are performed and the current set
value is displayed. (Default: 1)
Change the set value and press [START] key to make a copy under the set conditions.
To change the mode, press [
value is displayed. (Default: 1)
Change the set value and press [START] key to make a copy under the set conditions.
To change the mode, press [
] [
] key. The code number of the selected mode is
dip0slayed on the LCD/display.
[Operation]
The operation is similar to simulation 46-01.
The operation is similar to simulation 46-01.
32
Copier color reproduction
setup
setup
[Function]
Used to set color reproduction in each mode. Colors easy to be copied and colors difficult to be
copied can be switched.
Used to set color reproduction in each mode. Colors easy to be copied and colors difficult to be
copied can be switched.
* This setting has virtually no effect on black-and-white documents.
When this simulation is executed, warm-up and shading are performed and the current set
value is displayed. (Default: 0)
Press [START] key to make a copy under the set conditions . At that time, color components are
changed for used in copying.
To change the mode, press [
value is displayed. (Default: 0)
Press [START] key to make a copy under the set conditions . At that time, color components are
changed for used in copying.
To change the mode, press [
] [
] key. The code number of the selected mode is
dip0slayed on the LCD/display.
[Operation]
The operation is similar to simulation 46-01.
The operation is similar to simulation 46-01.
Main
code
code
Sub
code
Contents
Details of function/operation
Image quality
Setting No
Remark
Blurring
0
Standard
1
Default
Sharpening
2
Mode
Display item
LED
Default
AE mode
AE
COPY mode lamp
1
TEXT mode
TEXT
PRINT mode lamp
1
PHOTO mode
PHOTO
SCAN mode lamp
1
TS mode (TEXT)
TSTXT
PRINT mode lamp
SCAN mode lamp
SCAN mode lamp
1
TS mode (AE)
TSAE
COPY mode lamp
SCAN mode lamp
SCAN mode lamp
1
Dither mode
D_PHO
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
PRINT mode lamp
SCAN mode lamp
1
Set value
Colors easy to be copied
Colors difficult to be copied
0
Purple, Blue, Red
Yellow, Green, Water blue
1
Water blue, Green, Blue
Purple, Red, Yellow
2
Yellow, Red, Green
Blue, Water blue, Purple
Specification component
Setting No
Remark
Green
0
Default
Red
1
Blue
2
Mode
Display item
LED
Default
AE mode (including TS)
AE
COPY mode lamp
0
TEXT mode (including TS)
TEXT
PRINT mode lamp
0
PHOTO mode
PHOTO
SCAN mode lamp
0
Click on the first or last page to see other MX-B201D (serv.man9) service manuals if exist.