Sharp MX-B201D (serv.man9) Service Manual ▷ View online
MX-B201/B201D SIMULATION, TROUBLE CODES 10 - 10
22
14
ROM version display
[Function]
The P-ROM version is displayed.
Press [Numeric] key or [
The P-ROM version is displayed.
Press [Numeric] key or [
] [
] key to switch the display version.
[Operation]
16
Duplex counter display
(MX-B201D only)
(MX-B201D only)
[Function]
The duplex counter is displayed.
The duplex counter is displayed.
[Operation]
17
Copy counter display
[Function]
The copy counter is displayed.
The copy counter is displayed.
[Operation]
18
Printer counter display
[Function]
The printer counter is displayed.
The printer counter is displayed.
[Operation]
19
Scanner mode counter
display
display
[Function]
The scanner mode counter is displayed.
The scanner mode counter is displayed.
[Operation]
20
Password display
[Function]
Password (personal identification number to be managed by the department) is to be displayed.
[Operation]
Password (personal identification number to be managed by the department) is to be displayed.
[Operation]
21
Scanner counter display
[Function]
The scanner counter is displayed.
The scanner counter is displayed.
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
Code number
Version
Display item
0
Main unit Program
MAIN PROG.
1
ANB Program
ANB PROG.
2
AFAX Program
AFAX PROG.
3
LCD DATA
LCD DATA
1) Initial display
2) [Numeric] key or [
] key
2) [Numeric] key or [
] key
22-14 ROM VER.
MAIN PROG. 00.00
22-14 ROM VER.
ANB PROG. 00.00
22-14 ROM VER.
LCD DATA 00.00
1
1) Initial display
22-16 DPLX CNT
***,***
1) Initial display
22-17 COPIES CNT
***,***
1) Initial display
22-18 PRT.CNT
***,***
1) Initial display
22-19 S-MODE CNT
***,***
1) Initial display
22-20 PASSWORD
*****
1) Initial display
22-21 SCAN CNT
***,***
：'11/Oct/17
1
MX-B201/B201D SIMULATION, TROUBLE CODES 10 - 11
：'11/Oct/17
1
22
22
RSPF JAM counter display
[Function]
The RSPF JAM counter is displayed.
The RSPF JAM counter is displayed.
[Operation]
24
01
JAM total counter clear
[Function]
When [ENTER]/[START] key is pressed, the JAM total counter is cleared to 0 and "000,000" is
displayed on the LCD/display.
When [ENTER]/[START] key is pressed, the JAM total counter is cleared to 0 and "000,000" is
displayed on the LCD/display.
[Operation]
04
RSPF counter clear
[Function]
When [ENTER]/[START] key is pressed, the RSPF counter value is cleared to 0 and "000,000"
is displayed on the LCD/display.
When [ENTER]/[START] key is pressed, the RSPF counter value is cleared to 0 and "000,000"
is displayed on the LCD/display.
[Operation]
05
Duplex counter clear
(MX-B201D only)
(MX-B201D only)
[Function]
When [ENTER]/[START] key is pressed, the duplex counter value is cleared to 0, and "000,000"
is displayed on the LCD/display.
When [ENTER]/[START] key is pressed, the duplex counter value is cleared to 0, and "000,000"
is displayed on the LCD/display.
[Operation]
06
Developer counter clear
[Function]
When [OK]/[ENTER]/[START] key is pressed, the developer counter value is cleared to 0, and
"000,000" is displayed.
When [OK]/[ENTER]/[START] key is pressed, the developer counter value is cleared to 0, and
"000,000" is displayed.
[Operation]
07
Drum counter clear
[Function]
When [ENTER]/[START] key is pressed, the drum counter value is cleared to 0, and "000,000"
is displayed on the LCD/display.
When [ENTER]/[START] key is pressed, the drum counter value is cleared to 0, and "000,000"
is displayed on the LCD/display.
[Operation]
08
Copy counter clear
[Function]
When [ENTER]/[START] key is pressed, the copy counter value is cleared to 0, and "000,000" is
displayed on the LCD/display.
When [ENTER]/[START] key is pressed, the copy counter value is cleared to 0, and "000,000" is
displayed on the LCD/display.
[Operation]
09
Printer counter clear
[Function]
When [ENTER]/[START] key is pressed, the printer counter value is cleared to 0, and "000,000"
is displayed on the LCD/display.
When [ENTER]/[START] key is pressed, the printer counter value is cleared to 0, and "000,000"
is displayed on the LCD/display.
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
1) Initial display
22-22 S JAM CNT
***,***
1) Initial display
24-01 JAM TTL CLR.
CLEARED 000,000
1) Initial display
24-04 SPF CLR.
CLEARED 000,000
1
1) Initial display
24-05 DPLX CLR.
CLEARED 000,000
1) Initial display
24-06 DVLP CLR.
CLEARED 000,000
1) Initial display
24-07 DRUM CLR.
CLEARED 000,000
1) Initial display
24-08 COPIES CLR.
CLEARED 000,000
1) Initial display
24-09 PRT.CLR.
CLEARED 000,000
MX-B201/B201D SIMULATION, TROUBLE CODES 10 - 12
24
10
FAX counter clear
(When MX-FX12 is installed)
(When MX-FX12 is installed)
[Function]
When [ENTER]/[START] key is pressed, the FAX count value is set to 0 and "(000,000)" is dis-
played on the LCD.
When [ENTER]/[START] key is pressed, the FAX count value is set to 0 and "(000,000)" is dis-
played on the LCD.
[Operation]
13
Scanner counter clear
[Function]
When [ENTER]/[START] key is pressed, the scanner counter value is cleared to 0, and
"000,000" is displayed on the LCD/display.
When [ENTER]/[START] key is pressed, the scanner counter value is cleared to 0, and
"000,000" is displayed on the LCD/display.
[Operation]
14
RSPF JAM total counter
clear
clear
[Function]
When [ENTER]/[START] key is pressed, the RSPF JAM total counter value is cleared to 0, and
"000,000" is displayed on the LCD/display.
When [ENTER]/[START] key is pressed, the RSPF JAM total counter value is cleared to 0, and
"000,000" is displayed on the LCD/display.
[Operation]
15
Scanner mode counter clear
[Function]
When [ENTER]/[START] key is pressed, the scanner mode counter value is cleared to 0, and
"000,000" is displayed on the LCD/display.
When [ENTER]/[START] key is pressed, the scanner mode counter value is cleared to 0, and
"000,000" is displayed on the LCD/display.
[Operation]
25
01
Main motor operation check
(Cooling fan motor rotation
check)
(Cooling fan motor rotation
check)
[Function]
When [ENTER]/[START] key is pressed, the main motor (and the duplex motor in the case of a
duplex model) is operated for 30sec.
When [ENTER]/[START] key is pressed, the main motor (and the duplex motor in the case of a
duplex model) is operated for 30sec.
To reduce toner consumption, if the developing unit is installed, the developing bias, the main
charger, and the grid are also outputted.
charger, and the grid are also outputted.
In this case, laser discharge is required when stopping the motor, the polygon motor is also
operated at the same time. Check for installation of the developing unit. If it is not installed, the
high voltage above is not outputted and only the motor is rotated.
operated at the same time. Check for installation of the developing unit. If it is not installed, the
high voltage above is not outputted and only the motor is rotated.
To check the developing bias, install the developing unit.
After completion of 30sec operation, the machine goes into the sub code entry standby mode.
[Operation]
10
Polygon motor ON
[Function]
When [ENTER]/[START] key is pressed, the Bios is called to rotate the polygon motor for
30sec.
After completion of 30sec operation, the operation is turned off with the Bios and the machine
goes into the sub code entry standby mode.
When [ENTER]/[START] key is pressed, the Bios is called to rotate the polygon motor for
30sec.
After completion of 30sec operation, the operation is turned off with the Bios and the machine
goes into the sub code entry standby mode.
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
1
1) Initial display
24-10 FAX CLR.
CLEARED 000,000
1) Initial display
24-13 SCAN CLR.
CLEARED 000,000
1) Initial display
24-14 S JAM TTL CLR.
CLEARED 000,000
1) Initial display
24-15 S-MODE CLR.
CLEARED 000,000
1) Initial display
25-01 MAIN MOTOR CHK
EXECUTING...
1) Initial display
25-10 LSU CHK
EXECUTING...
：'11/Oct/17
1
MX-B201/B201D SIMULATION, TROUBLE CODES 10 - 13
：'11/Oct/17
1
26
02
RSPF setup
[Function]
When this simulation is executed, the current set SPF/RSPF is displayed. Enter the code num-
ber corresponding to the desired SPF/RSPF and press [ENTER]/[START] key to save the set-
ting.
When this simulation is executed, the current set SPF/RSPF is displayed. Enter the code num-
ber corresponding to the desired SPF/RSPF and press [ENTER]/[START] key to save the set-
ting.
[Operation]
03
2ND TRAY setup
[Function]
When this simulation is executed,the current set 2ND TRAY is displayed. Enter the code num-
ber corresponding to the desired 2ND TRAY and press [ENTER]/[START] key to save the set-
ting.
When this simulation is executed,the current set 2ND TRAY is displayed. Enter the code num-
ber corresponding to the desired 2ND TRAY and press [ENTER]/[START] key to save the set-
ting.
[Operation]
The operation is similar to simulation 26-02.
The operation is similar to simulation 26-02.
04
Machine duplex setup
(DPLX)
(DPLX)
[Function]
When this simulation is executed, the current set duplex is displayed. Enter the code number
corresponding to the desired duplex and press [ENTER]/[START] key to save the setting.
When this simulation is executed, the current set duplex is displayed. Enter the code number
corresponding to the desired duplex and press [ENTER]/[START] key to save the setting.
MX-B201 cannot be executed.
[Operation]
The operation is similar to simulation 26-02.
The operation is similar to simulation 26-02.
06
Destination setup
[Function]
When this simulation is executed, the current set destination is displayed. Enter the code num-
ber corresponding to the desired destination and press [ENTER]/[START] key to save the set-
ting.
When this simulation is executed, the current set destination is displayed. Enter the code num-
ber corresponding to the desired destination and press [ENTER]/[START] key to save the set-
ting.
* Code numbers 2 and 3 cannot be selected for the MX-B201 and MX-B201D.
Note 1:
With a change of the setting, the counter for ‘AE limit setting’ is to be cleared to zero (SIM46-
30). The setting of the tray, if the paper size for it is set to the size of inch series, is to be
changed to the tray for the “Letter”. However, the setting of the tray, if the size of the paper for it
is set to any other size, is to be changed to the “A4”.
With a change of the setting, the counter for ‘AE limit setting’ is to be cleared to zero (SIM46-
30). The setting of the tray, if the paper size for it is set to the size of inch series, is to be
changed to the tray for the “Letter”. However, the setting of the tray, if the size of the paper for it
is set to any other size, is to be changed to the “A4”.
Note 2:
For any other models than those for Japan, the mark “-” is to be displayed, if the code 2 is
selected.
For any other models than those for Japan, the mark “-” is to be displayed, if the code 2 is
selected.
[Operation]
The operation is similar to simulation 26-02.
The operation is similar to simulation 26-02.
Main
code
code
Sub
code
Contents
Details of function/operation
Code number
SPF/RSPF
Display item
0
SPF NO
SPF OFF
1
SPF YES
SPF ON
2
RSPF YES
RSPF ON
1) The current set value is
displayed.
2) [Numeric] key or [
] key
2) [Numeric] key or [
] key
3) [ENTER]/[START] key
26-02 SPF/RSPF
1:SPF ON (0- 2)
26-02 SPF/RSPF
0:SPF OFF (0- 2)
26-02 SPF/RSPF
2:RSPF ON (0- 2)
26-02 SPF/RSPF
2:RSPF ON (0- 2)
Code number
2ND TRAY
Display item
0
2ND TRAY NO
OFF
1
2ND TRAY YES
ON
1
Code number
Duplex
Display item
0
Duplex NO
OFF
1
Duplex YES
ON
1
Code number
Destination
Display item
0
Inch series
INCH
1
EX Japan AB series
AB
2
Japan AB series
JAPAN
3
China
CHINA
1
Click on the first or last page to see other MX-B201D (serv.man9) service manuals if exist.