DOWNLOAD Sharp MX-B201D (serv.man9) Service Manual ↓ Size: 16.14 MB | Pages: 127 in PDF or view online for FREE

MX-B201/B201D  SIMULATION, TROUBLE CODES  10 - 14

26

07

Machine conditions check

[Function]
When this simulation is executed, the current machine setting is displayed.

20

Rear edge void setup

[Function]
When this simulation is executed, the current set rear edge void is displayed. Enter the code
number corresponding to the desired rear edge void and press [ENTER]/[START] key to save
the setting.

[Operation]
The operation is similar to simulation 26-02.

30

CE mark support control 
ON/OFF

[Function]
When this simulation is executed, the current set CE mark support control is displayed. Enter
the code number corresponding to the desired CE mark support control and press [ENTER]/
[START] key to save the setting.

[Operation]
The operation is similar to simulation 26-02.

37

Cancel of stop at developer 
life over

[Function]
When this simulation is executed, the current setting is displayed. When the code number is
entered and [START] key is pressed, the setting is changed.

39

Memory capacity check

[Function]
When the simulation is executed, the currently installed SDRAM of the main unit is displayed.

40

Polygon motor OFF time 
setup (Time required for 
turning OFF after completion 
of printing)

[Function]
When this simulation is executed, the current setting is displayed. Enter the code number corre-
sponding to the desired setting and press [ENTER]/[START] key to save the setting.

[Operation]
The operation is similar to simulation 26-02.

Main 
code

Sub 

code

Contents

Details of function/operation

CPM

Copy quantity 

Remark

20 CPM

20

1) The machine setting is displayed. 

26-07 CPM

20 CPM

Code number

Setting

Display item

Remark

0

Rear edge void NO

OFF

1

Rear edge void YES

ON

Default

Code number

Setting

Display item

Remark

0

CE mark support control OFF

OFF

Default (100V series)

1

CE mark support control ON

ON

Code number

Setting

Remark

0

Stop at developer life over

1

Cancel of stop at developer life over

Default

Code number

Setting

Remark

32

32 MBYTE

64

64 MBYTE

1) Memory capacity display 

26-39 MEM.CHK

32 MBYTE

Code number

Setting

Display item

Remark

0

0sec

0  SEC.

1

30sec

30 SEC.

Default

2

60sec

60 SEC.

3

90sec

90 SEC.

：'11/Oct/17

MX-B201/B201D  SIMULATION, TROUBLE CODES  10 - 15

26

42

Transfer ON timing control 
setup

Main 
code

Sub 

code

Contents

Details of function/operation

When this simulation is executed, the currently set code number is displayed.

Enter the code number and press the [START] key, and the setting will be changed. (For any
number different from the following ones, the default time is automatically set.)

The adjustment can be made individually for each of the following modes.

<Paper lead edge adjustment table>

Note 1: 
The default code ‘11’ for the transfer ON timing indicates a lapse of 236ms from PS release.

Note 2: 
If the code “0” is selected, the setting is the same as the default setting ‘11’.

Note 3: 
The transfer ON timing can be adjusted in increments/decrements of 2ms within the range of
236ms±20ms.

<Front/back surface of paper rear edge adjustment table>

* The default "50" of the transfer OFF timing indicates "210msec passed from PPD1OFF."

* The transfer OFF timing can be adjusted to 210msec ± 2ms.

Mode

Display item

Default

Setting range

Front surface paper lead edge

F-REAR

 11

0 - 21

Front surface paper rear edge

F-END

 50

1 - 99

Back surface paper lead edge

B-REAR

 11

0 - 21

Back surface paper rear edge

B-END

 50

1 - 99

Code

Setting

Remark

0

0  msec

1

–20 msec

. . .

. . .

10

–2 msec

11

0 msec

Default

12

2 msec

. . .

. . .

21

20 msec

Code

Setting

Remark

1

–98 msec

. . .

. . .

49

–2 msec

50

0 msec

Default

51

+2 msec

. . .

. . .

99

+98 msec

1) Initial display 

<Front surface lead edge setting>

2) [

]  [

]  key: Mode selection

3) [Numeric] key: Value entry

4) [ENTER]/[START] key: 

Settles the entered value. The display is
shifted to the sub code input standby
menu.

26-42 TC ON TIMING

F-REAR     11( 0-21 )

26-42 TC ON TIMING

F-END      50( 1-99 )

26-42 TC ON TIMING

F-END      51( 1-99 )

MX-B201/B201D  SIMULATION, TROUBLE CODES  10 - 16

26

43

Side void setup

[Function]
When this simulation is executed, the currently set code of the side void quantity is displayed
(initial display), and the set data are saved. (Setting range: 0 – 10, Default: 4 (= One side
2.0mm)) 

* When the adjustment value is increased by 1, the side void is changed as follows:

Side void adjustment: The side void is increased by 0.5mm. (The side void of "Set value x
0.5mm" is made.)

[Operation]
The operation is similar to simulation 09-04.

54

γ life correction setting

[Function]
Used to set the 

γ life correction.

When this simulation is executed, the current set code number is displayed.

Enter the desired code number and press [ENTER]/[START] key to save the setting. 
(Setting range: 0 – 1, default: 1)

[Operation]
The operation is similar to simulation 26-02.

62

Energy-save mode copy 
lamp setup

[Function]
Used to set half-ON /OFF of the copy lamp in the pre-heat mode.

When this simulation is executed, the current set code number is displayed. Enter the desired
code number and press [ENTER]/[START] key to save the setting.

[Operation]
The operation is similar to simulation 26-02.

69

Use to set the operation 
conditions for toner near end

[Function]
This simulation is used to set the operating conditions for toner near end.

For except Japan, China performs operation of set value "3" regardless of the setting value.

Main 
code

Sub 

code

Contents

Details of function/operation

Code

Setting

Remark

0

0  mm

1

0.5  mm

2

1.0  mm

3

1.5  mm

4

2.0 mm

Default

5

2.5  mm

6

3.0  mm

7

3.5  mm

8

4.0  mm

9

4.5  mm

10

5.0 mm

Code number

Setting

Display item

Remark

0

OFF

OFF

1

ON

ON

Default

Code number

Setting

Display item

Remark

0

Copy  lamp  OFF

OFF

1

Copy lamp half-ON

ON

Default

<Toner near end display/No display>

<Setting of operations at toner end>

Code number

Setting contents

0

Toner near end is displayed

1

Toner near end is not displayed

Code number

Setting contents

1

Operation setting 1

2

Operation setting 2

3

Operation setting 3

MX-B201/B201D  SIMULATION, TROUBLE CODES  10 - 17

30

01

Paper sensor status display

[Function]
The paper sensor status is displayed on the LCD.

41

06

OC cover float detection 
level adjustment
(Only when RSPF installed)

[Function]
When this simulation is executed, the current set value is displayed. When [ENTER]/[START]
key is pressed, the mirror base unit moves to the RSPF scan position to acquire the OC cover
float detection level.

When the mirror base unit returns to the home position, the acquired value is displayed.

If the adjustment is NG, the following message is displayed.

The LCD indicates "ERR."

Note that, this simulation must be executed with the OC cover closed.
∗ If the value is 0, float detection is not performed in normal jobs.

07

OC cover float detection 
margin setting
(Only when RSPF installed)

[Function]
For the number of pixels between black markers on the SPF/RSFP scanning position saved in
"41-06: (OC cover float detection level adjustment)", if the number of pixels between the mark-
ers when processing float detection is less than the number of pixels set with this simulation, it
is judged as the float error.

When the set value of this simulation is "0," no float error occurs.

When this simulation is executed, the current set value is displayed.

Enter the adjustment value with [Numeric] key and press [START] key. The setting is saved and
the display is shifted to the sub code input standby menu. 
Setting range: 0 – 99 (Copes with margin 0 – 99 pixels.)

Default: 30 (30 pixels)

[Operation]
The operation is similar to simulation 9-04.

Main 
code

Sub 

code

Contents

Details of function/operation

Sensor

Display item

Paper exit sensor

POD

Paper width detection for Tray 1

PD1

Paper width detection for Tray 2

PD2

Paper entry sensor  

PPD1

Duplex sensor

PPD2

New drum cartridge sensor

DRST

1) Initial display

2) When sensor ON

30-01 P-SENSOR

30-01 POD  PD1  PD2

PPD1 PPD2 DRST

1) Initial display

2) [ENTER]/[START] key

41-06 OC FLOAT LEVEL

               0    

41-06 OC FLOAT LEVEL

EXECUTING...

<Canceling - when [Clear]/[Clear All] key is pressed->

After canceling, the machine goes into the sub code entry
standby mode.

3) When the level is acquired:

3) When the level is not acquired:

THE JOB IS BEING

CANCELED.

41-06 OC FLOAT LEVEL

             **** OK 

41-06 OC FLOAT LEVEL

             **** ERR