Sharp MX-6500N / MX-7500N (serv.man12) Service Manual ▷ View online
MX-7500N MX-CF11 (INSERTER) 16 – 1
MX-7500N
Service Manual
[16] MX-CF11 (INSERTER)
1. Unpacking
A. Inserter unpacking
NOTE: When moving the inserter, use manpower of three or more
persons.
B. Fixing tape and protection material removal
1) Remove the fixing t ape and the protection material from the
inserter.
C. Packed items check
* The quantity of safety plate is running-changed from 2 to 1 after
September, 2012 production.
No.
Name
Quan
tity
Front
Rear
MX-
RB15
MX-
RB13
MX-
FD10
1
Accessory cover
1
1
1
1
2
Tray unit front cover
1
1
1
1
3
Base cover (Tray unit)
1
1
1
1
4
Connection plate L
(Finisher side)
1
---
---
1
5
Connection plate R
(Finisher side)
1
---
---
1
6*
Safety plate
2
2
2
---
7
Earth plate
1
1
1
1
8
Connection plate L
(Machine side)
1
1
---
---
9
Connection plate R
(Machine side)
1
1
---
---
10
Black Mylar
1
1
---
---
11
Height adjustment saucer
4
4
4
4
12
"L" hinge pin
(Tray unit front cover)
2
2
2
2
13
Screw (4 x 8L)
1
1
1
1
14
Blue screw (4 x 8L)
4
4
---
---
15
Blue screw (3 x 8L)
1
---
---
---
16
Screw (4 x 12L)
3
3
3
3
17
Screw (4 x 20L)
2
2
2
2
18
Screw (4 x 6L)
6
6
---
---
19
Front surface cushion (Long)
2
2
2
2
20
Front surface cushion (Short)
1
1
1
1
21
Winding bushing 6 x 8L
2
2
2
2
22
Gasket (for Taiwan only)
3
1
2
2
MX-7500N MX-CF11 (INSERTER) 16 – 2
2. Installation
NOTE: Before installation, be sure to turn both the operation and
main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
A. Attaching the cushion
1) Attach the front surface cushion (Long) (Packed items No. 19)
and the front surface cushion (Short) (Packed items No. 20) to
the reference as shown below.
B. Paper guide B (bundled with the decurler unit)
installation
(When installing the paper folding machine)
1) Attach the Black Mylar (Packed items No.10) to the paper
guide B.
Attach the Black Myla r to the downstream side of the paper
Attach the Black Myla r to the downstream side of the paper
guide.
Attachment reference
Attach to the notch in the rear side as the reference.
Attach to the notch in the rear side as the reference.
2) Fix the connection plate L/R (Finisher side) (Packed items
No.4 and 5) to the p aper exit side of the inserter with the
screws (Packed items No.18 Screw 4x6L).
3) Install the paper guide B (bundled with the decurler unit No.12)
to the paper exit side of the inserter with the screws (bundled
with the decurler unit No.1).
NOTE: When connecting the MX-RB13 to the back, attach the
paper guide D (bundled with the relay unit No. 9).
C. Earth plate installation
1) Remove the earth plate from the lower section of the inserter
and turn the removed earth plate back and attach it as shown
in the photo below..
2) Attach the earth plate (Packed items No.7), and fix it with the
screw (Packed items No.18).
Cushion (Long)
Cushion (Long)
Cushion (Short)
Cushion (Long)
Cushion
Cushion
Cushion (Short)
reference
reference
reference
reference
reference
reference
Attach the cushion (Short) in
series with the cushion (Long).
series with the cushion (Long).
R side
Black Mylar
Notch
Earth plate
MX-7500N MX-CF11 (INSERTER) 16 – 3
D. Paper guide C (bundled with the decurler unit)
installation
1) Install the paper guide C (bundled with the decurler unit No.13)
to the paper feed side of the inserter with the screws (bundled
with the decurler unit No.1).
E. Gasket installation ( Only for Taiwan)
1) Stick a gasket (Packed items No.22) to the paper feed side of
the inserter as the following reference.
F. Installation of the connection plate and the
protection Mylar to the decurler unit
1) Remove the decurler unit plates.
2) Attach the pr otection sheet ( bundled with the decurler unit
No.14) to the decurler unit with the screw (bundled with the
decurler unit No.1).
MEMO: Temporarily attach the protection sheet to the decurler
MEMO: Temporarily attach the protection sheet to the decurler
unit with the duplex tape (back of the protection sheet), then fix
it with the screw.
3) Attach the connection plate F/R (Packed items No.8, 9) to the
decurler unit with the screws (Packed items No.18 Scr ew
4x6L).
G. Connection with the decurler unit
1) Open the inserter front upper cover, remove the scr ew, and
pull the lock lever toward you.
2) Connect the inserter to the decurler unit.
Insert the pin in the decurler unit side into the unit hole.
Photo viewed from the R side
Photo viewed from the R side
20mm from the cover line
Frame line
MX-7500N MX-CF11 (INSERTER) 16 – 4
3) Push up the lock lever to lock the unit and the decurler unit.
Use the removed screw to fix the lock lever.
MEMO: If they cannot be locked, follow the inst alling proce-
MEMO: If they cannot be locked, follow the inst alling proce-
dures (height adjustment) of the complex machine and options
to adjust the height.
H. Fall-prevention stay storing
1) Loosen the scr ew of the fall- prevention stay, and store the
stay.
I. Tray unit installation
For installation of the tray unit, use manpower of two or more per-
sons.
1) Remove the rear cover of the tray unit.
1) Remove the rear cover of the tray unit.
2) Hold the grip of the unit to install it to the inserter.
NOTE: When the tray unit is in serted, the machine becomes
unstable. In order to prevent against falling, therefore,
connect the after-process mechanism (the finisher,
etc.) the fall-prevention to the lef t side of the inserter
and put the tray unit on it.
3) Attach the screw (Packed items No. 16) .
4) Connect five connectors.
4) Connect five connectors.
5) Remove the front inner cover. (2 screws)
6) Fix the tray unit. (2 screws (Packed items No. 16))
6) Fix the tray unit. (2 screws (Packed items No. 16))
Fall-prevention stay
Rear cover
Plate grip (Used for installation)
Plate grip
Grip
Screw (M4 x 12)
Connect five connectors.
Front inner cover
Tray unit
Screw (M4 x 12)
Click on the first or last page to see other MX-6500N / MX-7500N (serv.man12) service manuals if exist.