DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man46) Service Manual ↓ Size: 3.61 MB | Pages: 127 in PDF or view online for FREE

MX-7000N  SIMULATION  7 – 105

Operation/Procedure
1)

Select an output target mode with the touch panel.

2)

Press [EXECUTE] key.
A signal is outputted at the send level set with the soft switch.
When [EXECUTE] key is pressed, the signal output can be
stopped.

 

66-19

Backup

Function (Purpose) Used to backup the address book data

stored in the HDD. (Backup to the Flash
ROM)

Operation/Procedure
1)

Press [EXECUTE] key.

2)

Press [YES] key.
The address book data in the HDD are saved to the Flash
ROM.

 

66-20

Data transfer

Function (Purpose) Used to transfer the address book data

stored in the Flash ROM. (Transfer to HDD)

Operation/Procedure
1)

Press [EXECUTE] key.

2)

Press [YES]  key.
The address book data are transferred from the Flash ROM to
the HDD.

 

66-21

Adjustment, setting, operation data check

Function (Purpose) Used to print information abut FAX (various

registrations, communication manage-
ment, file management, system errors, pro-
tocols).

FAX

Operation/Procedure
1)

Select a print target item with the touch panel key.

2)

Press [EXECUTE] key.
Printing is started.

 

66-24

Clear

Function (Purpose) Used to clear the FAST memory data.
Section

FAX

Operation/Procedure
1)

Press [EXECUTE] key.

2)

Press [YES] key.
The FAST memory data are cleared.

 

66-25

Setting

Function (Purpose) Used to register a FAX number for MODEM

dial-in.

FAX

Operation/Procedure
1)

Enter a MODEM dial-in FAX number (0 - 9, *, #) with 10-key.
The upper limit is 20 digits.

2)

Press [SET] key.
The MODEM dial-in FAX number is registered.

SIMULATION NO.66-18

TEST

DTMF SIGNAL OUTPUT.(SOFT SW.)

EXECUTE

CLOSE

1

2

3

4

5

6

7

8

9

0

#

ARE YOU SURE?

YES

NO

EXECUTE

SIMULATION NO.66-19

TEST

ADDRESS DATA BACK UP. (WRITE TO FLASH ROM)

CLOSE

ARE YOU SURE?

YES

NO

EXECUTE

SIMULATION NO.66-20

TEST

ADDRESS DATA BACK UP. (READ FROM FLASH ROM)

CLOSE

EXECUTE

SIMULATION NO.66-21

TEST

FAX INFORMATION PRINT OUT.

CLOSE

REGISTERED

MANAGEMENT

FILE MANAGEMENT

SYSTEM ERROR LINE

PROTOCOL LINE

ARE YOU SURE?

YES

NO

EXECUTE

SIMULATION NO.66-24

TEST

FAST MEMORY CLEAR.

CLOSE

SIMULATION NO.66-25

TEST

CLOSE

PRESENT : --------------------

NEW :

SET

M-D-IN FAX NUMBER SETTING. 0-9[0-9]. :[ ]:#:[#]

MX-7000N  SIMULATION  7 – 106

 

66-26

Setting

Function (Purpose) Used to register an external telephone

number for MODEM dial-in.

FAX

Operation/Procedure
1)

Enter a MODEM dial-in external telephone number (0 - 9, *, #)
with 10-key. The upper limit is 20 digits.

2)

Press [SET] key.
The MODEM dial-in external telephone number is registered.

 

66-29

Data clear

Function (Purpose) Used to clear the data related to the

address book (one-touch registration, FTP/
Desktop extension, group extension, pro-
gram registration, interface memory box,
meta data, Inbound Routing, Document
Admin table).

Operation/Procedure
1)

Press [EXECUTE] key.

2)

Press [YES] key.
The data related to the address book are cleared.

 

66-30

Operation test, check

Function (Purpose) Used to check a change in the TEL/LIU sta-

tus.

FAX

Operation/Procedure
The TEL/LIU status is displayed.
(Signal detected: Highlighted display, Signal not-detected: Normal
display)

 

66-31

Operation check

Function (Purpose) Used to set the TEL/LIU output port.
Section

FAX

Operation/Procedure
1)

Select the port to be turned ON with the touch panel key. 
(ON: Highlighted display)

2)

Press [EXECUTE] key.
The setting is reflected.
When [EXECUTE] key is pressed, the operation can be
stopped.

 

66-32

Operation test, check

Function (Purpose) Used to check the received data (fixed

data) from the line.

FAX

Operation/Procedure
1)

Press [EXECUTE] key.
The fixed data received from the line are checked.

2)

When the check is completed normally, "OK" is displayed.
When an error occurs, "NG" is displayed.
When [EXECUTE] key is pressed, the operation can be
stopped.

 

66-33

Operation test, check

Function (Purpose) Used to detect the line signals (BUSY

TONE/CNG/CED/FNET/DTMF).

FAX

Operation/Procedure
Select a target item for signal detection check with the touch panel
key.
The detected signal is highlighted.

HS1

Polarity reversal signal

HS2

Polarity reversal signal

RHS

Handset hook SW

EXHS

External telephone hook SW

SIMULATION NO.66-26

TEST

CLOSE

PRESENT : --------------------

NEW :

SET

M-D-IN EXTEL NUMBER SETTING. 0-9[0-9]. :[ ]:#:[#]

ARE YOU SURE?

YES

NO

EXECUTE

SIMULATION NO.66-29

TEST

FAX ADDRESS DATA CLEAR.

CLOSE

TEL/LIU SENSOR CHECK

CLOSE

SIMULATION NO.66-30

TEST

HS1

HS2

RHS

EXHS

SIMULATION NO.66-31

TEST

TEL/LIU SETTING.

EXECUTE

CLOSE

CION

MR

EC

S.

RECEIVED DATA CHECK

CLOSE

SIMULATION NO.66-32

TEST

CHECKING...

EXECUTE

MX-7000N  SIMULATION  7 – 107

 

66-34

Operation test, check

Function (Purpose) Used to measure the communication time

of the send test image data. 

FAX

Operation/Procedure
The send test is performed and the send time is measures and dis-
played. (Unit: ms)

 

66-36

Operation test, check

Function (Purpose) Used to perform the interface check

between the MFP controller and the
MDMC. (Data line or command line check)

FAX

Operation/Procedure
1)

Select a target item for the operation check with the touch
panel key.

2)

Press [EXECUTE] key.
If "(once)" is selected, when check is completed normally,
"OK" is displayed. When there occurs an error, "NG" is dis-
played.
If "(repeat)" is selected, check is repeated until the result is
found "NG" or until [EXECUTE] key is pressed.

 

66-39

Setting

Function (Purpose) Used to set the destination.
Section

FAX

Operation/Procedure
Select a destination with the touch panel key.

 

66-42

Setting

Function (Purpose) Used to rewrite the power control program

again to the FAX BOX.

FAX

Operation/Procedure
1)

Press [EXECUTE] key.

2)

Press [YES] key.
When writing the program is completed normally, "OK" is dis-
played. When writing is failed, "NG" is displayed.

 

66-43

Setting

Function (Purpose) Used to write the adjustment value of the

power control program to the FAX BOX.

FAX

Operation/Procedure
1)

Select a target item to be set with [

↑] [↓] keys.

2)

Enter a set value with 10-key.

3)

Press [EXECUTE] key.
When writing the adjustment value is completed normally,
"OK" is displayed. When it fails, "NG" is displayed.

MFP 

← MDMC (DATA once)

Data line once only

MFP 

→ MDMC (DATA once)

Data line once only

MFP 

← MDMC (DATA repeat)

Data lien repeat

MFP 

→ MDMC (DATA repeat)

Data line repeat

MFP 

← MDMC (CMD once)

Command line once only

MFP 

→ MDMC (CMD once)

Command line once only

MFP 

← MDMC (CMD repeat)

Command line repeat

MFP 

→ MDMC (CMD repeat)

Command line repeat

SIMULATION NO.66-33

TEST

SIGNAL DETECT CHECK.

CLOSE

FNET

BT/CNG/CED/DT

SIMULATION NO.66-34

TEST

COMMUNICATION TIME DISPLAY.

CLOSE

####[ms]

EXECUTE

SIMULATION NO.66-36

TEST

MFP-MDMC I/F CHECK.

CLOSE

MFP<-MDMC (DATA once)

MFP->MDMC (DATA once)

MFP<-MDMC (DATA repeat)

MFP->MDMC (DATA repeat)

MFP<-MDMC (CMD once)

MFP->MDMC (CMD once)

MFP<-MDMC (CMD repeat)

MFP->MDMC (CMD repeat)

A

CI_LEVEL_JUDGE

2 - 15

3

B

CI_CYCLE_MIN

1 - 254

10

C

CI_CYCLE_MAX

2 - 255

142

D

CI_COUNT

2 - 15

3

E

POFF_LEVEL_JUDGE

2 - 15

15

F

EXHS_LEVEL_JUDGE

2 - 255

240

G

RHS_LEVEL_JUDGE

2 - 15

2

H

SON_TIMEOUT

1 - 127

20

SIMULATION NO.66-39

TEST

FAX DESTINATION SETUP

CLOSE

JAPAN

U.S.A/CANADA

EUROPE

AUSTRALIA

CHINA

ASIA&OTHERS

ARE YOU SURE?

YES

NO

EXECUTE

SIMULATION NO.66-42

TEST

POWER CONTROL PROGRAM RELOAD

CLOSE

MX-7000N  SIMULATION  7 – 108

 

 

67-17

Setting

Function (Purpose) Used to set the printer controller memory

clear and default value.

Operation/Procedure
1)

Press [EXECUTE] key.

2)

Press [YES] key.
Used to clear the printer controller memory and to set the
default values. 
If setting is not completed normally, "ERROR" is displayed.

 

67-24

Adjustment/Setting

Function (Purpose) Used to perform the printer setting of auto

color calibration. 
* When FIERY is supported, SIM is not dis-
played.

Operation/Procedure
1)

Press [EXECUTE] key.
The high density process control operation is started to make
self print. 

2)

Place the outputted self print patch on the glass table, and
select a process mode with [FACTORY] and [SERVICE] on
the touch panel.

3)

Press [EXECUTE] key.
The patch is scanned and the 16-patch self print is outputted. 

4)

Press [OK] key.
The correction value is saved and the reference value is regis-
tered. 

 

67-25

Adjustment/Setting

Function (Purpose) Used to perform the manual correction set-

ting of the printer engine color balance. 
* When FIERY is supported, SIM is not dis-
played.

Operation/Procedure
1)

Select an adjustment target color with [K][C][M][Y] keys on the
touch panel. 

2)

Select an item to be set with [

↑] and [↓] keys.

3)

Enter the adjustment value with 10-key.

4)

Press [OK] key. (The set value is saved.)

 

67-26

Adjustment/Setting

Function (Purpose) Used to perform the reference scanner tar-

get value setting of the printer engine auto
density adjustment. 
* When FIERY is supported, SIM is not dis-
played.

Operation/Procedure
Select a target item to be changed with the touch panel. 
The set value is saved. 

A :

3

CI_LEVEL_JUDGE

B  10

CI_CYCLE_MIN

C  142

CI_CYCLE_MAX

D 

3

CI_COUNT

A:

SIMULATION NO.66-43

POWER CONTROL ADJUSTMENT VALUE WRITING.

3

2

15

OK

TEST

EXECUTE

CLOSE

E  15

POFF_LEVEL_JUDGE

F  240

EXHS_LEVEL_JUDGE

G 

2

RHS_LEVEL_JUDGE

H 20

SON_TIMEOUT

SIMULATION NO.67-17

TEST

PRINTER CONTROLLER MEMORY CLEAR

CLOSE

EXECUTE

ARE YOU SURE?

YES

NO

SIMULATION NO.67-24

TEST

PRINTER ENGINE HALFTONE AUTO ADJUSTMENT MODE

EXECUTE

CLOSE

PRESS [EXECUTE] TO PROCON EXECUTION AND PRINT THE TEST PATCH.

(PLEASE USE SPECIFIED TYPE OF A3 OR 11" 17" SIZE PAPER

FOR THIS ADJUSTMENT)

SIMULATION NO.67-24

TEST

PRINTER ENGINE HALFTONE AUTO ADJUSTMENT MODE

PLEASE SELECT THE MODE (FACTORY) OR (SERVICE) AND PLACE

THE PRINTED TEST PATCH ON DOCUMENT GLASS THEN PRESS [EXECUTE].

*LIGHT AREA AT LEFT SIDE ON DOCUMENT GLASS.

,

SERVICE

FACTORY

EXECUTE

CLOSE

A : 50

;

POINT1

B : 50

;

POINT2

C : 50

;

POINT3

D : 50

;

POINT4

A:

SIMULATION NO.67-25

PRINTER ENGINE COLOR BALANCE MANUAL ADJUSTMENT: PG

50

1

99

OK

TEST

CLOSE

E : 50

;

POINT5

F : 50

;

POINT6

G : 50

;

POINT7

H : 50

;

POINT8

I : 50

;

POINT9

J : 50

;

POINT10

K : 50

;

POINT11

L : 50

;

POINT12

EXECUTE

K

C

M

Y