Sharp MX-5500N / MX-6200N / MX-7000N (serv.man46) Service Manual ▷ View online
MX-7000N SIMULATION 7 – 93
Operation/Procedure
1)
1)
Press [EXECUTE] key.
2)
Press [YES] key.
Read/write is executed.
Read/write is executed.
62-6
Purpose
Operation test/Check
Function (Purpose) Used to perform the self diagnostics of the
hard disk.
Section
Operation/Procedure
1)
1)
Select a target item of the self diagnostics.
2)
Press [EXECUTE] key.
The self diagnostics is started.
The self diagnostics is started.
62-7
Purpose
Operation test/Check
Function (Purpose) Used to print the hard disk self diagnostics
error log.
Section
Operation/Procedure
1)
1)
Press [EXECUTE] key.
2)
Printing the error log is started.
62-8
Purpose
Function (Purpose) Used to format the hard disk. (Excluding
Function (Purpose) Used to format the hard disk. (Excluding
the system area and the operation manual
area)
area)
Section
Operation/Procedure
1)
1)
Press [EXECUTE] key.
2)
Press [YES] key.
Formatting the hard disk is started.
Formatting the hard disk is started.
62-10
Purpose
Data clear
Function (Purpose) Used to delete the job log data.
Section
Section
Operation/Procedure
1)
1)
Press [EXECUTE] key.
2)
Press [YES] key.
Delete of the job log data is started.
Delete of the job log data is started.
62-11
Purpose
Data clear
Function (Purpose) Used to delete the document filing data.
Section
Section
Operation/Procedure
1)
1)
Press [EXECUTE] key.
2)
Press [YES] key.
Delete of the document filing data is executed.
Delete of the document filing data is executed.
62-12
Purpose
Setting
Function (Purpose) Used to set Enable/Disable of auto format
in a hard disk trouble.
Section
Operation/Procedure
1)
1)
Enter the adjustment value with 10-key.
2)
Press [OK] key. (The set value is saved.)
SHORT S.T
Partial check
EXTENDED S.T
All areas check
ARE YOU SURE?
YES
NO
SIMULATION NO.62-03
TEST
HDD R/W TEST(ALL)
CLOSE
EXECUTE
SIMULATION NO.62-06
TEST
SMART OFFLINE TEST
EXECUTE
SHORT S.T
ENABLE
:
1/1
CLOSE
EXTENDED S.T
DISABLE
:
SIMULATION NO.62-07
TEST
SMART ERROR LOG PRINT OUT
EXECUTE
CLOSE
PRESS [EXECUTE] TO PRINT THE SMART ERROR PRINT
A
0: Enable
1: Disable (Default)
1: Disable (Default)
SIMULATION NO.62-08
TEST
HDD FORMAT(EXCEPT SYSTEM AREA)
CLOSE
EXECUTE
ARE YOU SURE?
YES
NO
SIMULATION NO.62-10
TEST
JOB COMPLETE DATA CLEAR(WITH JOB LOG DATA)
CLOSE
EXECUTE
ARE YOU SURE?
YES
NO
SIMULATION NO.62-11
TEST
DOCUMENT FILING DATA CLEAR
CLOSE
EXECUTE
ARE YOU SURE?
YES
NO
MX-7000N SIMULATION 7 – 94
62-13
Purpose
Function (Purpose) Used to format the hard disk. (only the
Function (Purpose) Used to format the hard disk. (only the
operation manual area)
Section
Operation/Procedure
1)
1)
Press [EXECUTE] key.
2)
Press [YES] key.
Formatting the hard disk is started.
Formatting the hard disk is started.
63
63-1
Purpose
Adjustment/Setting/Operation data check
Function (Purpose) Used to check the shading correction
result.
Section
Scanner
Operation/Procedure
1)
1)
Select a target color to display with [R] [G] [B] on the touch
panel.
panel.
2)
Select the display target mode from [OC] and [DSPF].
63-2
Purpose
Adjustment
Function (Purpose) Used to perform shading.
Section
Section
Operation/Procedure
1)
1)
Select a target mode for execution with [OC SHADING] and
[DSPF SHADING] on the touch panel.
[DSPF SHADING] on the touch panel.
2)
Press [EXECUTE] key.
Shading is executed.
Shading is executed.
63-3
Purpose
Adjustment/Setting
Function (Purpose) Used to perform scanner color balance and
color coefficient auto adjustment.
Section
Scanner
Operation/Procedure
1)
1)
Select an adjustment target with [R] [G] [B] on the touch panel.
2)
Select a target mode with [OC] and [DSPF].
3)
Press [EXECUTE] key.
4)
The color auto adjustment is executed.
OC
GAIN ODD
Gain adjustment value (odd number)
GAIN_EVEN
Gain adjustment value (Even number)
OFFSET ODD
Offset value (odd number)
OFFSET EVEN
Offset value (even number)
SMP AVE ODD
Reference plate sampling average
value (ODD)
value (ODD)
SMP AVE EVEN
Reference plate sampling average
value (EVEN)
value (EVEN)
TARGET VALUE
Target value
BLACK LEVEL
Black output level
ERROR CODE
Error code
DSPF FACE WHITE
LEVEL 1ST
LEVEL 1ST
First scan DSPF front surface white
reference level
reference level
DSPF FACE WHITE
LEVEL 2ND
LEVEL 2ND
Second scan DSPF front surface
white reference level
white reference level
A : 1
;
(0:YES 1:NO)
A:
SIMULATION NO.62-12
AUTO FORMAT SETTING (HDD TROUBLE)
1
0
1
OK
TEST
CLOSE
SIMULATION NO.62-13
TEST
HDD FORMAT(MANUAL AREA ONLY)
CLOSE
EXECUTE
ARE YOU SURE?
YES
NO
DSPF
GAIN ODD
Gain adjustment value (odd number)
GAIN_EVEN
Gain adjustment value (Even number)
OFFSET ODD
Offset value (odd number)
OFFSET EVEN
Offset value (even number)
SMP AVE ODD
Reference plate sampling average
value (ODD)
value (ODD)
SMP AVE EVEN
Reference plate sampling average
value (EVEN)
value (EVEN)
TARGET VALUE
Target value
BLACK LEVEL
Black output level
ERROR CODE
Error code
DSPF BACK WHITE
LEVEL 1ST
LEVEL 1ST
First scan DSPF back surface white
reference level
reference level
DSPF BACK WHITE
LEVEL 2ND
LEVEL 2ND
Second scan DSPF back surface
white reference level
white reference level
OC SHADING
OC analog level correction and shading correction
data making (Document table mode)
data making (Document table mode)
DSPF SHADING
DSPF analog level correction and shading correction
data making (DSPF mode)
data making (DSPF mode)
OFFSET ODD
0
:
SIMULATION NO.63-01
TEST
SHADING DATA DISPLAY
CLOSE
GAIN ODD
147
:
GAIN EVEN
143
:
OFFSET EVEN
0
:
SMP AVE ODD
0
:
SMP AVE EVEN
0
:
TARGET VALUE
0
:
BLACK LEVEL
0
:
ERROR CODE
0
:
DSPF FACE WHITE LEVEL 1ST
0
:
1/1
DSPF
B
G
R
OC
DSPF FACE WHITE LEVEL 2ND
0
:
SIMULATION NO.63-02
TEST
SHADING EXECUTION
EXECUTE
CLOSE
SELECT OC SHADING/DSPF SHADING, AND PRESS EXECUTE
DSPF SHADING
OC SHADING
MX-7000N SIMULATION 7 – 95
63-5
Purpose
Adjustment/Setting
Function (Purpose) Used to perform the scanner color balance
and the color coefficient auto adjustment.
Section
Operation/Procedure
1)
1)
Select a target of the initial value reset with [SIDE A(OC)]
[SIDE B (DSPF)] on the touch panel.
[SIDE B (DSPF)] on the touch panel.
2)
Press [EXECUTE] key, and press [OK] key.
The initial value is saved.
The initial value is saved.
63-6
Purpose
Adjustment/Setting
Function (Purpose) Used to perform the engine color balance
auto adjustment pattern setting.
Section
Operation/Procedure
1)
1)
Place the chart self-printed with SIM 46-21 on the glass table.
2)
Press [EXECUTE] key.
3)
The sampling value of each patch is displayed.
63-7
Purpose
Adjustment/Setting
Function (Purpose) Used to perform the auto density setting of
the engine auto adjustment scanner target
value. (Servicing)
value. (Servicing)
Section
Operation/Procedure
1)
1)
Press [SETUP] key on the touch panel.
Sampling is executed.
Sampling is executed.
2)
Place the chart self-printed with SIM 46-21 on the glass table.
3)
Press [EXECUTE] key.
Sampling of each patch is executed.
Sampling of each patch is executed.
4)
Press [OK] key.
The displayed sampling result is saved as the target value.
The displayed sampling result is saved as the target value.
63-8
Purpose
Adjustment/Setting
Function (Purpose) Used to perform the initial value reset of the
engine auto adjustment scanner target
value. (Servicing)
value. (Servicing)
Section
Operation/Procedure
1)
1)
Press [EXECUTE] key.
2)
Press [YES] key.
The initial value reset of the engine auto adjustment scanner
target value is executed.
The initial value reset of the engine auto adjustment scanner
target value is executed.
SIDE A
(OC)
(OC)
Copy gamma correction 1 and color correction coefficient
TWAIN gamma correction 1 and color correction coefficient
Auto adjustment gamma correction 1 and color correction
coefficient
TWAIN gamma correction 1 and color correction coefficient
Auto adjustment gamma correction 1 and color correction
coefficient
SIDE B
(DSPF)
(DSPF)
Copy gamma correction 1 and color correction coefficient
TWAIN gamma correction 1 and color correction coefficient
TWAIN gamma correction 1 and color correction coefficient
CLOSE
OC
SIMULATION NO.63-03
TEST
SCANNER COLOR BALANCE AUTO ADJUSUTMENT
OC
#1:197, #2:185, #3:165, #4:148, #5:117, #6:110,
#7: 88, #8: 75, #9: 55, #10: 45, #11: 38, #12: 29,
#19: 5, #20:
4, #22: 2, #:24: 2
#13: 27, #14: 21, #15: 18, #:16: 15, #17: 10, #18: 8,
1/2
DSPF
B
G
R
C#2:180, C#6:141, C#12: 89
R#2:166, R#6: 43, R#12: 4
M#2:180, M#6:141, M#12: 89
G#2:166, G#6: 43, G#12: 4
Y#2:180, Y#6: 141, Y#12: 89
B#2:166, B#6: 43, B#12: 4
ARE YOU SURE?
YES
NO
EXECUTE
SIMULATION NO.63-05
TEST
STANDARD SCANNER GAMMA SETUP
1/1
CLOSE
SIDE A(OC)
SIDE B(DSPF)
B
Point B target value
C
Point C target value
D
Point D target value
E
Point E target value
F
Point F target value
G
Point G target value
H
Point H target value
I
Point I target value
J
Point J target value
K
Point K target value
L
Point L target value
M
Point M target value
N
Point N target value
O
Point O target value
BASE
Background sampling value
SIMULATION NO.63-06
TEST
ENGINE COLOR BALANCE CHART READING
CLOSE
EXECUTE
SET THE CHART ON PLATEN AND TOUCH [EXECUTE]
K
C
M
Y
SETUP
SIMULATION NO.63-07
TEST
SCANNER TARGET OF COLOR CALIB SETUP:SERVICE
#B:
91, #C
2944, #D:
3227, #E:
5822, #F:
8600
#G: 28935, #H: 54344, #I: 86968, #J: 122678, #K: 151198
#L: 169731, #M: 195950, #N: 201249, #:O: 207112
1/1
CLOSE
MX-7000N SIMULATION 7 – 96
63-11
Purpose
Adjustment/Setting
Function (Purpose) Used to set the reference scanner target
value for the engine auto density adjust-
ment.
ment.
Section
Operation/Procedure
Select a target item to be changed with the touch panel.
The set value is saved.
Select a target item to be changed with the touch panel.
The set value is saved.
64
64-1
Purpose
Operation test/Check
Function (Purpose) Used to perform the self print. (Color mode)
Section
Section
Operation/Procedure
1)
1)
Select a target color for self print with [K] [C] [M] [Y] on the
touch panel.
touch panel.
2)
Select a target item to print with [
↑] and [↓] keys.
3)
Enter the adjustment value with 10-key.
4)
Press [EXECUTE] key.
Self printing is started.
Self printing is started.
*: HEAVY1 (Not Havy2)
Item
Default value
Target value table
select
select
DEF1
DEF1 mode setting
DEF 1
DEF2
DEF2 mode setting
DEF3
DEF3 mode setting
SIMULATION NO.63-08
TEST
STANDARD SCANNER TARGET SETTING:SERVICE
CLOSE
EXECUTE
ARE YOU SURE?
YES
NO
SIMULATION NO.63-11
TEST
STANDARD SCANNER TARGET SELECT OF ENGINE HALFTONE AUTO ADJUSTMENT
TARGET TBL
DEF1
DEF2
CLOSE
1/1
DEF3
:
Item
Default value
A
PRINT PATTERN (1, 2, 9 - 11, 14 - 19)
Print pattern specification
1
B
DOT1 (DOT1 >= 2 IF A: 2,11)
Print dot number setting
1
C
DOT2 (DOT2 >= 2 IF A: 2,11)
Empty dot number setting
254
D
DENSITY (FIXED "255" IF A: 9)
Print gradation setting
255
E
MULTI COUNT
Print quantity
1
F
EXPOSURE (2 - 8 IF A: 14 - 19)
THROUGH
Specification of the
exposure mode.
exposure mode.
1: No process (through)
8
CHAR/PIC
2: Text/Printed Photo
CHAR/PRPIC
3: Text/Photograph
CHAR
4: Text
PRINT PIC
5: Printed photo
PRINT PAPER
6: Photograph
MAP
7: Map
STANDARD DITCH
8: Dither without correction
G
PAPER
MFT
Tray selection
1: Manual feed
2
CS1
2: Tray 1
CS2
3: Tray 2
CS3
4: Tray 3
CS4
5: Tray 4
LCC
6: LCC
H
DUPLEX
YES
Duplex print select
0: Select
1
NO
1: Not selected
I
PAPER TYPE
PLAIN
Paper type
1: Normal paper
1
HEAVY *
2: Heavy paper
OHP
3: OHP
ENVELOPE
4: Envelope
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man46) service manuals if exist.