Sharp MX-5500N / MX-6200N / MX-7000N (serv.man25) Peripheral ▷ View online
61
Fiery X3eTY2 system software
T
O
INSTALL
SYSTEM
SOFTWARE
USING
A
PREPARED
USB
FLASH
DRIVE
1.
If your USB flash drive is not yet prepared, complete the procedure beginning on
page 58.
page 58.
2.
Shut down and power off the Fiery X3eTY2 and MFP (see page 6).
3.
Disconnect all cables from the Fiery X3eTY2 connector panel, except for the power cable.
Leave the power cable connected to the Fiery X3eTY2.
4.
Make sure the service switches are in the normal (OFF) position (both switches are away
from “ON”).
from “ON”).
See Figure AB. If needed, remove the cover plate to access the service switches.
F
IGURE
AB
Service switches on the Fiery X3eTY2
5.
Attach the prepared USB flash drive to one of the USB-Type A connectors on the
Fiery X3eTY2 (see Figure W on page 44).
Fiery X3eTY2 (see Figure W on page 44).
For convenience, you can attach the USB extension cable (provided) to the
Fiery X3eTY2 and then attach the USB flash drive to the other end of the cable.
Fiery X3eTY2 and then attach the USB flash drive to the other end of the cable.
N
OTE
:
If dust covers are attached to the USB-Type A connectors, remove one dust cover
using needlenose pliers.
Service switches
Verify that service switches are in normal (OFF) position...
...not in service mode (ON) position.
Power switch
LED display
62
Fiery X3eTY2 system software
6.
Power on the Fiery X3eTY2 using its dedicated power switch.
7.
Wait several minutes while the files are transferred (usually between 6 and 20 minutes,
depending on the size of the system software).
depending on the size of the system software).
The LED on the flash drive shows sporadic activity. The LED display on the
Fiery X3eTY2 shows sporadic activity at first; then it increments from 00, increasing one
number every 30 seconds until done.
Fiery X3eTY2 shows sporadic activity at first; then it increments from 00, increasing one
number every 30 seconds until done.
The Fiery X3eTY2 automatically powers off when the installation is done.
8.
Move the Fiery X3eTY2 power switch to OFF (0) position.
9.
Wait at least 30 seconds, and then remove the USB flash drive from the Fiery X3eTY2.
10.
Reconnect the cables between the Fiery X3eTY2 and the MFP (see Figure W on page 44).
11.
Power on the MFP using the main power switch inside the front compartment, and then
the secondary power switch on the Control Panel. Then power on the Fiery X3eTY2 using
its dedicated power switch.
the secondary power switch on the Control Panel. Then power on the Fiery X3eTY2 using
its dedicated power switch.
Allow the MFP to start up.
12.
When the “Initializing print controller. Please wait” message appears on the MFP touch
panel, press OK.
panel, press OK.
13.
Complete the steps listed below for your MFP model:
MX-7000/6200/5500
MX-4500/3500
• Press the Copy tab on the MFP touch
panel.
• Press the Fiery icon at the bottom of
the touch panel.
• Wait for the Fiery Settings button to
become available; then press Fiery
Settings.
Settings.
• Wait for the Select Language screen to
appear.
The Select Language screen appears.
• Press the System Settings button on
the MFP.
• On the touch panel, press Admin
Password and then press Password.
• On the touch panel, use the keyboard
to enter the administrator password for
the MFP. Press OK and then press OK
again at the next screen.
the MFP. Press OK and then press OK
again at the next screen.
This password is not the same as the
administrator password for the
Fiery X3eTY2.
administrator password for the
Fiery X3eTY2.
• At the System Settings screen, use the
arrows to scroll to Printer Settings and
press Printer Settings.
press Printer Settings.
The Select Language screen appears.
63
Fiery X3eTY2 system software
14.
Use the arrows on the left to display the customer’s desired language, and then press the
selection key on the right that corresponds to OK.
selection key on the right that corresponds to OK.
15.
If the Select Market Region screen appears, scroll to the name of the region for the
Fiery X3eTY2 and select OK.
Fiery X3eTY2 and select OK.
N
OTE
:
This screen appears only if English was selected from the language selection screen.
After you select the language and market region, a screen appears prompting you to enter
the administrator password for the Fiery X3eTY2.
the administrator password for the Fiery X3eTY2.
16.
Use the keyboard to enter “Fiery.1” as the password, and press OK. If an additional
screen appears, press OK again.
screen appears, press OK again.
This is the default administrator password for the Fiery X3eTY2.
N
OTE
:
The password is case-sensitive. Enter
Fiery.1
exactly as shown.
17.
At the Setup screen, reenter the customer’s settings from the Configuration page that
you printed earlier.
you printed earlier.
Enter settings for Server, Network, and Printer Setup, in that order. If it is more
appropriate for the network administrator to enter the settings, then bypass the settings
not included on the Configuration page. For more information, see Configuration and
Setup.
appropriate for the network administrator to enter the settings, then bypass the settings
not included on the Configuration page. For more information, see Configuration and
Setup.
18.
After all setup options are configured, select Exit Setup from the Setup screen.
The Fiery X3eTY2 reboots with the updated system software and setup options.
19.
Allow the Fiery X3eTY2 to reach Idle.
20.
If you have been given any patches (system update files) for this version of system
software, install them now.
software, install them now.
For more information, see the instructions provided with each patch.
64
Specifications
Specifications
Hardware features
• Intel Celeron 2.0GHz CPU
• 256MB memory
• Hard disk drive (HDD)
• Battery—3V manganese dioxide lithium coin cell (Panasonic CR2032 or equivalent)
• 180W power supply with 100-240VAC input voltage
• Independent power switch
Networking and connectivity
The Fiery X3eTY2 has the following networking features:
• Supports AppleTalk, TCP/IP, and IPX protocols simultaneously
• RJ-45 port for straight-through Ethernet (10BaseT/100BaseTX/1000BaseT) network
connection
User software
A complete description of Fiery X3eTY2 user software is provided in the Welcome user
document. You must install the latest user software onto all computers that print to the
Fiery X3eTY2. Using incompatible versions of the system and user software may result in
system problems.
document. You must install the latest user software onto all computers that print to the
Fiery X3eTY2. Using incompatible versions of the system and user software may result in
system problems.
Safety and emissions compliance
The Fiery X3eTY2 is certified to meet or surpass the following standards:
Safety approvals
EMC approvals
• UL 60950-1:2003 (TÜV/CU Mark)
• FCC Class B
• CAN/CSA 22.2 #60950-1-03
• VCCI Class B
• EN 60950-1 (TÜV/GS Mark)
• EN55022 Class B
• CB scheme IEC 60950-1:2001
• EN55024
• AS/NZS CISPR 22 Class B
• AS/NZS 4252.1
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man25) service manuals if exist.