Sharp MX-5500N / MX-6200N / MX-7000N (serv.man25) Peripheral ▷ View online
49
Restoring functionality after service
T
O
CONNECT
THE
F
IERY
X3
E
TY2
TO
THE
NETWORK
1.
Shut down and power off the Fiery X3eTY2, as described on page 6.
2.
Connect the network cable to the Ethernet network at the customer site.
3.
Connect the other end of the cable to the network connector on Fiery X3eTY2
(see Figure W on page 44).
(see Figure W on page 44).
4.
Ask the network administrator whether DHCP is enabled for the network.
If DHCP is enabled, the Fiery X3eTY2 is automatically configured for use over the
network.
network.
If DHCP is not enabled, allow the network administrator to perform Network Setup on
the Fiery X3eTY2. For information about Network Setup, see the Configuration and
Setup user document that accompanies the Fiery X3eTY2.
the Fiery X3eTY2. For information about Network Setup, see the Configuration and
Setup user document that accompanies the Fiery X3eTY2.
5.
Allow the network administrator to verify the Fiery X3eTY2 network connection by
downloading a print job from a remote workstation.
downloading a print job from a remote workstation.
50
Fiery X3eTY2 system software
Fiery X3eTY2 system software
The Fiery X3eTY2 system software is installed on the HDD at the factory. You must
install system software if a more recent version is required, you replace the HDD, or you
discover problems with the current system. To upgrade to a newer version of system
software, use one of the following methods:
install system software if a more recent version is required, you replace the HDD, or you
discover problems with the current system. To upgrade to a newer version of system
software, use one of the following methods:
• Install complete system software over the network port (see page 51)
• Install complete system software using a USB flash drive (see page 57)
System software installation reminders
When installing system software, remember the following:
•
Fonts
—Installing system software deletes all fonts that the customer has installed
on the Fiery X3eTY2. Only resident fonts are restored during system software
installation. You can use the Downloader utility to reinstall additional fonts.
installation. You can use the Downloader utility to reinstall additional fonts.
To determine which additional fonts were downloaded to the Fiery X3eTY2, print the
Fonts List before you format the HDD and again after you complete the system
software installation. Reinstall any fonts not listed after installation. For information
about how to print the Fonts List, see “Printing Fiery X3eTY2 pages” on page 46.
Fonts List before you format the HDD and again after you complete the system
software installation. Reinstall any fonts not listed after installation. For information
about how to print the Fonts List, see “Printing Fiery X3eTY2 pages” on page 46.
•
Language
—Installing system software screens are always displayed in English, even if
the MFP is configured for another language.
•
Compatibility
—Install the latest user software onto all computers that print to the
Fiery X3eTY2. Using incompatible versions of the system and user software may result
in system problems.
in system problems.
•
Configuration
—Print a Configuration page before installing any software when
upgrading or reinstalling the system software (for instructions, see page 46). The Setup
configurations are lost when you install system software.
configurations are lost when you install system software.
51
Fiery X3eTY2 system software
Installing system software over the network port
The System Software CDs contain the system software and the system software installer.
To install system software using the network port on the Fiery X3eTY2, you need:
To install system software using the network port on the Fiery X3eTY2, you need:
• A crossover Ethernet cable (4-pair/8-wire, short-length)
The MFP Ethernet cable is a crossover Ethernet cable, and may be used for system
software installation.
software installation.
• A Windows XP/2000 computer with:
• A CD-ROM drive, built in or attached
• Support for 100BaseTX or 1000BaseT
T
O
INSTALL
SYSTEM
SOFTWARE
OVER
THE
NETWORK
PORT
N
OTE
:
Before beginning system software installation, disable all Internet firewalls and
anti-virus software on the Windows XP/2000 computer.
1.
Shut down and power off the Fiery X3eTY2 and MFP (see page 6).
2.
Remove all external cables from the Fiery X3eTY2, except for the power cable.
Leave the power cable connected to the Fiery X3eTY2.
52
Fiery X3eTY2 system software
3.
Connect the Ethernet crossover cable to the Fiery X3eTY2 network port and to a
Windows XP/2000 computer (see Figure Z)
Windows XP/2000 computer (see Figure Z)
N
OTE
:
The MFP Ethernet cable is an Ethernet crossover cable. To use the cable in this
step, disconnect the cable from the Fiery X3eTY2 and the MFP. For information about
how to identify a crossover cable, see Figure Y on page 48.
how to identify a crossover cable, see Figure Y on page 48.
F
IGURE
Z
Creating an isolated Ethernet network using a crossover cable
4.
Power on the computer and insert System Software CD 1 into the computer CD-ROM drive.
5.
If the installer does not start automatically, navigate to the CD-ROM drive and
double-click the drive icon.
double-click the drive icon.
6.
At the Welcome screen, click Next.
7.
Read the Software License Agreement. Select “I Agree” to continue the installation
process, and then click Next.
process, and then click Next.
8.
At the Connection Type screen, make sure Ethernet is selected. Click Next to advance to
the Confirmation screen.
the Confirmation screen.
N
OTE
:
Ignore the text and graphics on this Confirmation screen. The graphics on this
screen may not accurately depict Fiery X3eTY2 hardware.
Network connector
Windows 2000/XP computer
Ethernet crossover cable
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man25) service manuals if exist.