Sharp MX-5500N / MX-6200N / MX-7000N (serv.man25) Peripheral ▷ View online
29
Removing and replacing Fiery X3eTY2 components
2.
Connect the CPU fan cable to the motherboard connector FAN1.
If you are installing a replacement CPU cooling assembly, secure the slack in the fan cable
using a tie-wrap, if necessary. The tie-wrap prevents the fan cable from interfering with
the CPU fan. Also, make sure the connector on the cable is securely attached to
connector FAN1 on the motherboard.
using a tie-wrap, if necessary. The tie-wrap prevents the fan cable from interfering with
the CPU fan. Also, make sure the connector on the cable is securely attached to
connector FAN1 on the motherboard.
3.
Replace the 4-pin power cable to its connector on the motherboard (see Figure G on
page 11).
page 11).
4.
Reassemble the Fiery X3eTY2 and verify functionality (see page 42).
CPU
Use the following procedures to remove and replace the CPU on the motherboard.
The CPU is installed in a Zero Insertion Force (ZIF) socket on the motherboard. Before
you can remove the CPU from its socket you need to remove the cooling assembly from
the CPU socket, as described on page 24.
you can remove the CPU from its socket you need to remove the cooling assembly from
the CPU socket, as described on page 24.
This section includes the following topics:
• “To remove the CPU” on page 30
• “To replace the CPU” on page 31
30
Removing and replacing Fiery X3eTY2 components
T
O
REMOVE
THE
CPU
1.
Access and open the Fiery X3eTY2, as described on page 8.
2.
Remove the CPU cooling assembly, as described on page 24.
3.
Lift the CPU socket lever to release the CPU from the socket.
To release the CPU, flex the lever away from the retention post on the socket, and then
lift the lever all the way up.
lift the lever all the way up.
F
IGURE
P
Removing/replacing a CPU
4.
Grasp the CPU by its edges and carefully lift it from the socket.
CPU
Arrow
Retention post
CPU socket
Pin 1
Lever
31
Removing and replacing Fiery X3eTY2 components
T
O
REPLACE
THE
CPU
1.
Raise the lever on the CPU socket.
Flex the lever away from the retention post on the socket, and then lift the lever all the
way up to release the CPU.
way up to release the CPU.
2.
Insert the CPU into the socket.
Align the arrow indicating pin 1 on the CPU with pin 1 in the CPU socket (see Figure P
on page 30).
on page 30).
3.
Lower the socket lever to secure the CPU.
Lock the lever in place beneath the retention post.
4.
Replace the CPU cooling assembly, as described on page 27.
5.
Reassemble the Fiery X3eTY2 and verify functionality (see page 42).
32
Removing and replacing Fiery X3eTY2 components
Exhaust fan
An exhaust fan is attached to the side of the pan to cool the system.
This section includes the following topics:
• “To remove the exhaust fan”
• “To replace the exhaust fan” on page 33
T
O
REMOVE
THE
EXHAUST
FAN
1.
Access and open the Fiery X3eTY2, as described on page 8.
2.
Detach the 3-pin fan cable connector from FAN3 connector on the motherboard.
3.
Remove the four plastic rivets that attach the fan to the side of the pan, and then
remove the fan.
remove the fan.
To remove a rivet, use a flathead screwdriver to pry loose the rivet head on the outside of
the chassis while squeezing and pushing the locking end of the rivet with your fingers or
a screwdriver. Set the rivets aside so that you can replace them later.
the chassis while squeezing and pushing the locking end of the rivet with your fingers or
a screwdriver. Set the rivets aside so that you can replace them later.
F
IGURE
Q
Removing the exhaust fan
Exhaust fan
Rivet (1 of 4)
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man25) service manuals if exist.