Sharp MX-5500N / MX-6200N / MX-7000N (serv.man25) Peripheral ▷ View online
17
Removing and replacing Fiery X3eTY2 components
T
O
REPLACE
OR
UPGRADE
A
DIMM
1.
Access and open the Fiery X3eTY2, as described on page 8.
2.
To release a DIMM, push outward on the levers on each side of the DIMM.
F
IGURE
K
Releasing a DIMM
3.
Lift the DIMM straight out of the socket.
4.
To replace a DIMM, position the DIMM in the socket and press the DIMM straight down
into the socket so the levers lock the DIMM into place.
into the socket so the levers lock the DIMM into place.
N
OTE
:
DIMMs fit in the socket only one way. The notch on the bottom of each DIMM
should line up with the notch in the socket.
Make sure that the levers close securely around the ends of the DIMM and each DIMM
is fully seated in its socket.
is fully seated in its socket.
N
OTE
:
For a single-DIMM configuration, you must install the DIMM in socket
DIMM2. Installing the single DIMM in socket DIMM1 is incorrect and can cause
problems with system performance.
problems with system performance.
5.
Reassemble the Fiery X3eTY2 and verify its functionality (see page 42).
6.
To verify memory capacity, print a Configuration page to check the amount of memory
recorded.
recorded.
Due to CPU overhead, the Configuration page may show slightly less memory than the
DIMM capacity.
DIMM capacity.
Lever
DIMM
Lever
Socket notch
18
Removing and replacing Fiery X3eTY2 components
Battery
The battery is located at BT1 on the motherboard. When replacing the battery, be sure to
use a 3V manganese dioxide lithium coin cell battery (Panasonic CR2032 or equivalent).
use a 3V manganese dioxide lithium coin cell battery (Panasonic CR2032 or equivalent).
CAUTION: There is danger of explosion if the battery is replaced with the incorrect type.
Replace only with the same type recommended by the manufacturer.
Replace only with the same type recommended by the manufacturer.
BATTERY DISPOSAL: This product contains a lithium primary (manganese dioxide)
memory back-up battery that must be disposed of properly. Remove the battery from the
product and contact your local environmental agencies for information on recycling and
disposal options.
memory back-up battery that must be disposed of properly. Remove the battery from the
product and contact your local environmental agencies for information on recycling and
disposal options.
TRAITEMENT DES PILES USAGÉES : Ce produit contient une pile de sauvegarde de memoire lithium primaire (dioxyde de
manganese) qui doit être traitée correctement. Enlevez la pile du produit et prenez contact avec votre agence environnementale
locale pour des informations sur les méthodes de recyclage et de traitement.
manganese) qui doit être traitée correctement. Enlevez la pile du produit et prenez contact avec votre agence environnementale
locale pour des informations sur les méthodes de recyclage et de traitement.
T
O
REPLACE
THE
BATTERY
1.
Access and open the Fiery X3eTY2 as described on page 8.
2.
Remove the interface board (see page 13).
Removing the interface board allows you to safely access the battery on the motherboard.
3.
Locate the battery on the motherboard. Carefully bend the clip that holds the battery.
Use caution when bending the clip; excessive force could cause the clip to lose tension.
F
IGURE
L
Fiery X3eTY2 battery
4.
Pull the battery from its socket and release the clip.
5.
Insert the new battery.
Slide the battery into the socket under the clip, with the positive (+) side facing out of the
socket. Make sure the clip holds the battery securely in the socket.
socket. Make sure the clip holds the battery securely in the socket.
6.
Reinstall the interface board (see page 16).
7.
Reassemble the Fiery X3eTY2 and verify functionality (see page 42).
8.
Configure the time and date in Setup.
Clip
Battery
Socket
+
19
Removing and replacing Fiery X3eTY2 components
Motherboard
Use the following procedures to remove and replace the Fiery X3eTY2 motherboard.
This section has the following topics:
• “To remove the motherboard”
• “To replace the motherboard” on page 21
T
O
REMOVE
THE
MOTHERBOARD
1.
Access and open the Fiery X3eTY2, as described on page 8.
2.
Remove the interface board from the motherboard (see page 13).
Place the removed board on an antistatic surface.
3.
Remove the following cables attached to the motherboard:
• Exhaust fan cable
• HDD data cable (including the grounding wire)
• 4-pin power cable
• 20-pin power cable
• Service board cable
For the locations of each connector on the motherboard, see Figure G on page 11.
20
Removing and replacing Fiery X3eTY2 components
4.
Remove the five mounting screws that secure the motherboard to the base of the
chassis pan.
chassis pan.
5.
Lift the edge of the motherboard opposite the connector panel to release the
motherboard from the pan. Gently slide the motherboard out of the pan, and place the
motherboard on a flat, anti-static surface.
motherboard from the pan. Gently slide the motherboard out of the pan, and place the
motherboard on a flat, anti-static surface.
Make sure the connectors on the motherboard clear the cutouts in the connector panel as
you remove the board. Avoid handling contacts or using excessive force.
you remove the board. Avoid handling contacts or using excessive force.
F
IGURE
M
Removing the motherboard from the pan
6.
If you are replacing the motherboard with a new motherboard, remove the following
from the old motherboard:
from the old motherboard:
• DIMM(s) (see page 16)
• CPU (see page 29)
Lift up edge of motherboard
and remove from pan.
and remove from pan.
Make sure motherboard
connectors clear cutouts
in the connector panel.
connectors clear cutouts
in the connector panel.
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man25) service manuals if exist.