DOWNLOAD Sharp MX-2630 Service Manual ↓ Size: 66.16 MB | Pages: 127 in PDF or view online for FREE

MX-2630N  MX-PN16B/C/D (PUNCH MODULE)  15 – 4

2)

Connect the connector on punch waste full sensor unit to the
punch unit.

1)

Wire the cable as shown in the photo below.

1)

Attach the Punch cushion A to the inner cover along the reference
face.

1)

Install the punch waste tray as shown in the photo below.

1)

Attach the top cover by moving toward the direction of an arrow 1.
Then slide the top cover in the direction of an arrow 2.

6HQVRUKROGHU

3XQFKZDVWHIXOOVHQVRUXQLW

+DUQHVVJXLGH

&DEOH

Reference face:

    

Touch inner cover with left side surface of Punch cushion A.

    

Touch Punch inner cover with back side of Punch cushion A.

Inner cover

Punch inner cover

Attach the cushion A.

Attach the cushion A.

3XQFKZDVWHWUD\

MX-2630N  MX-PN16B/C/D (PUNCH MODULE)  15 – 5

2)

Close the top cover.

3)

Close the front cabinet of the finisher.

4)

Incline upper part of the rear cabinet, hook the pawls of the rear
cabinet to the main unit and attach the rear cabinet.

5)

Fasten 2 screws to rear cabinet of the finisher.

1)

Put a punch position label (for scanner).

2)

Put a punch position label (for RSPF).

1)

Connect the power plug of the machine to the power outlet, and
turn ON the main power switch and the operation panel power
switch.

Position of the pawls of the rear cabinet 
and insertion slot on the finisher unit

Rear cabinet

Finisher unit

Use 2 screws for attachment.

)LWZLWKWKHFRUQHU5

/DEHODWWDFKPHQWUHIHUHQFH

&RUQHURIWKHXSSHU

FDELQHWERWWRP

)LWZLWKWKHFRUQHU5

RSPF

R2.5 connection line

Edge line R 2.5

CAUTION

Cleaning of the document scan section

When streaks appear on copy or scan

images, open the automatic document

feed unit and clean the document scan

section with the glass cleaner (accessory).

Document scan section

MX-2630N  MX-TR19 N (EXIT TRAY UNIT)  16 – 1

MX-2630N

Service Manual

 

Before installation, be sure to turn both the operation and main power
switches off and disconnect the power plug from the power outlet.
Make double sure that the data lamp on the operation panel does not
light up or blink when performing installation.

1)

Open the right door.

2)

Remove the screws. Remove the right upper cabinet.

1

EXIT TRAY UNIT

1

2

Right paper exit unit

1

3

Full detection actuator

1

4

M4×6S-tight

2

5

M4×10P-tight

1

6

Harness

(Not used)

1

3

6

4

5

1

2

MX-2630N  MX-TR19 N (EXIT TRAY UNIT)  16 – 2

3)

Remove the screws. Remove the ADU PG PH.

1)

Attach the right delivery unit lower to the original positions. Fix the
right delivery unit lower with the screws (4 pcs.)

M3x8 S-tight

A

M4x10 P-tight

B

M3x8 S-tight

C

M4x10 P-tight

D

M3x8 S-tight

A

M4x6 S-tight

B

M3x8 S-tight

C

M4x6 S-tight

D