DOWNLOAD Sharp MX-2630 Service Manual ↓ Size: 66.16 MB | Pages: 127 in PDF or view online for FREE

MX-2630N  MX-FN30 (FINISHER)  13 – 2

1)

Remove all fixing tapes/protection materials from the exterior.

2)

Open the front upper cover. Remove all tapes and take out the
protection materials from the stapler section.

3)

Close the front upper cover.

Ĭ

ĭ

Į

į

İ

ı

ı

IJ

ij

MX-2630N  MX-FN30 (FINISHER)  13 – 3

Check the firmware version.

If the firmware version is old, update the firmware.

Before starting the installation work, be sure to turn OFF the power
switch of the operation panel and the main power switch on the main
unit, and remove the power plug from the socket.

Check that the data lamp of the operation panel is not lit or blinking
before the installation work.

1)

Install the connection guide plate (Packed item No1.) with the
screws (x4) (Packed items No.5 M4x14 S- tight).

2)

Insert the rib of the interface pass guide (Packed item No.2) into
the hole of the main unit, and install it with the screw (Packed item
No.6 M3x6 S- tight).

1)

Install the earth plate (Packed items No.3) with the screws (x2)
(Packed item No.6 M3x6).

1)

Open the front cover. Install the stapler unit staple case (Packed
item No.4) into the stapler unit.

NOTE: The staple unit cannot be fixed if the power is OFF. When

installing the stapler unit staple case, insert it while holding it
so that the stapler unit cannot go deep inside.

A

B

C

MX-2630N  MX-FN30 (FINISHER)  13 – 4

1)

Fit the pin of the connection guide plate into the positioning hole of
the finisher.

1)

Check that the hole on the protrusion of the connection guide
plate is located between the marking lines of the protrusion of the
finisher.

*If the hole is not located between the marking lines, perform the
height/skew adjustment.

1)

Open the front cover.

2)

Unscrew the screw (x1) and remove the wrench.

3)

Turn the fixing nut of the caster in the direction of the arrow as
shown with the wrench, and then loosen it.

4)

When adjusting the height, make adjustment at 4casters shown in
the picture. 

Adjust the height of the adjusting nut of the caster by turning it in
the direction of the arrow as shown. (When turning the adjusting
nut 360-degree, the height of the finisher changes about
1.75mm.)

*For heightening the finisher: Turn the nut in [A] direction.

*For lowering the finisher: Turn the nut in [B] direction.

5)

When adjusting the skew, make adjustment at 2casters shown in
the picture. 

Adjust the skew of the adjusting nut of the caster by turning it in
the direction of the arrows as shown.

*For skewing the finisher to the right side: Turn the nut in [A] direc-
tion.

*For skewing the finisher to the left side: Turn the nut in [B] direc-
tion.

Marking  Line

Screw

[B]

[B]

[B]

[B]

[B]

[A]

[A]

[A]

[B]

MX-2630N  MX-FN30 (FINISHER)  13 – 5

6)

After the adjustment, return the wrench to the original position.

1)

Fix the lock slide plate with the screw (x1) (M3x6 S Tight).

Close the front cover of the finisher.

1)

Attach the connector of the finisher and fix it with the screw.

1)

Place the staple position label (for scanner)

2)

Place the staple position label (for RSPF)

1)

Insert the power plug into the socket, and turn ON the main power
switch and the power switch of the operation panel.

[B]

[A]

[A]

[B]

Screw

M3×6 S-tight

Ĭ

ĭ

)LWZLWKWKHFRUQHU5

)LWZLWKWKHFRUQHU5

/DEHODWWDFKPHQWUHIHUHQFH

&RUQHURIWKHXSSHU

FDELQHWERWWRP