Sharp MX-2300N / MX-2700N / MX-2300G / MX-2700G / MX-2300FG / MX-2700FG (serv.man18) User Manual / Operation Manual ▷ View online
44
Discarding punch waste (when a punch module is installed)
1
Open the cover.
2
Grasp the punch waste box handle,
gently pull out the box, and discard the
punch waste.
gently pull out the box, and discard the
punch waste.
Discard the punch waste in a plastic bag or other container,
taking care not to let the waste scatter.
taking care not to let the waste scatter.
3
Gently push the box back in.
4
Close the cover.
45
SADDLE STITCH FINISHER
The saddle stitch finisher is equipped with the offset function that offsets each set of output from the previous set, the
staple sort function that staples each set of output, and the saddle stitch function that automatically staples and folds
each set of output at the centreline.
An optional hole punching unit can also be installed to punch holes in output.
staple sort function that staples each set of output, and the saddle stitch function that automatically staples and folds
each set of output at the centreline.
An optional hole punching unit can also be installed to punch holes in output.
PART NAMES
(1)
Stapler compiler
This temporarily stacks paper to be stapled.
(2)
Output tray
Stapled and offset output is delivered to this tray.
The tray is slidable. Extend the tray for large output
(A3W, A3, B4, 12" x18", 11" x 17", 8-1/2" x 14" and
8-1/2" x 13" sizes).
The tray is slidable. Extend the tray for large output
(A3W, A3, B4, 12" x18", 11" x 17", 8-1/2" x 14" and
8-1/2" x 13" sizes).
(3)
Saddle stitch tray
Stapled and folded output is delivered to this tray.
(4)
Top cover
Open this cover to remove a paper misfeed.
(5)
Lever
To remove a staple jam or paper misfeed, pull this lever
and slide the saddle stitch finisher to the left until it stops.
and slide the saddle stitch finisher to the left until it stops.
(6)
Stapler section
Open the front cover and pull out this section to replace
the staple cartridge or remove a staple jam.
the staple cartridge or remove a staple jam.
(7)
Front cover
Open this cover to replace the staple cartridge or remove
a staple jam.
a staple jam.
SUPPLIES
The saddle stitch finisher requires the following staple cartridge:
• Staple cartridge
(approx. 5000 staples per cartridge x 3 cartridges)
AR-SC2
AR-SC2
(1)
(2)
(3)
(4)
(6)
(5)
(7)
• A paper pass unit is required to install a saddle stitch finisher.
• Do not place heavy objects on the saddle stitch finisher or press down on the saddle stitch finisher.
• Use caution when you turn on the power and when printing is taking place, as the tray may move up and down.
• A saddle stitch finisher and a finisher cannot be installed simultaneously.
46
SADDLE STITCH FINISHER MAINTENANCE
When the staple cartridge runs out of staples, a message will appear in the operation panel. Follow the procedure below
to replace the staple cartridge.
to replace the staple cartridge.
Replacing the staple cartridge
1
Open the front cover.
2
Pull out the stapler section.
Pull out until the stapler section until it stops.
3
Turn roller rotating knob A in the
direction of the arrow to move the staple
unit out to the front.
direction of the arrow to move the staple
unit out to the front.
Turn the roller rotating knob as shown until the triangle mark is
aligned with the indicator.
aligned with the indicator.
4
Remove the empty staple case.
5
Remove the empty staple cartridge.
Press the lock button to release the staple case cover and then
remove the staple cartridge.
remove the staple cartridge.
When staples remain, the staple cartridge cannot be removed.
Roller rotating knob A
Staple unit
47
6
Insert a new staple cartridge into the
staple case.
staple case.
Push the staple cartridge in until it clicks into place.
Do not remove the seal from the cartridge before inserting the cartridge into the case.
7
Pull the seal that holds the staples
straight out.
straight out.
8
Replace the staple case.
Push the staple case in until it clicks into place.
9
Push the stapler section back in.
Push the stapler section back in until it locks into its original
position.
position.
10
Close the front cover.
Make a test print or copy in staple sort mode to verify that stapling takes place correctly.
Click on the first or last page to see other MX-2300N / MX-2700N / MX-2300G / MX-2700G / MX-2300FG / MX-2700FG (serv.man18) service manuals if exist.