Sharp AR-PN1 Service Manual ▷ View online
5-5
CHAPTER 5 TROUBLESHOOTING
COPYRIGHT © 2001 CANON INC.
2000 2000 2000 2000
CANON SADDLE FINISHER G1 REV.0 MAR. 2001
1.2.3 Registering the Number of Punch Hole
Perform the following to register the type of puncher unit (number of holes) used to the
IC on the punch controller PCB for identification by the finisher. Be sure to register the type
whenever you have replaced the punch controller PCB.
1) Set bits 1 through 4 on the DIPSW1001 on the punch controller PCB as follows:
whenever you have replaced the punch controller PCB.
1) Set bits 1 through 4 on the DIPSW1001 on the punch controller PCB as follows:
F05-102-02
2) Press SW1002 on the punch controller PCB to select the appropriate number of punch
holes.
•
Each press on SW1002 moves the selection through the following (repeatedly from top
to bottom).
to bottom).
Number of punch holes
2 holes (Puncher Unit-J1)
2/3 holes (Puncher Unit-K1)
4 holes (Puncher Unit-G1)
4 holes (Puncher Unit-H1)
LED1002
OFF
ON
OFF
OFF
LED1003
OFF
OFF
OFF
ON
LED1001
ON
ON
OFF
OFF
ON
1
2
3
4
T05-102-01
3) Press SW1003 on the punch controller PCB twice. The presses will store the selected
number of punch holes on the punch controller PCB.
•
A single press on SW1003 will cause the LED indication to flash; another press on
SW1003 will cause the indication to remain ON to indicate the end of registration.
SW1003 will cause the indication to remain ON to indicate the end of registration.
4) Shift all bits of DIPSW1001 to OFF.
Chap05.p65
3/28/01, 12:11 PM
5
5-6
CHAPTER 5 TROUBLESHOOTING
COPYRIGHT © 2001 CANON INC.
2000 2000 2000 2000
CANON SADDLE FINISHER G1 REV.0 MAR. 2001
ON
1
2
3
4
1.2.4 After Replacing the EEP-ROM (IC1002)
1) Turn off the host machine.
2) Set bits 1 through 4 on the punch controller PCB as follows:
2) Set bits 1 through 4 on the punch controller PCB as follows:
F05-102-03
3) Press SW1002 and SW1003 on the punch controller PCB at the same time.
•
•
The presses will initialize the EEP-ROM. At the end, all LEDs (LED1001, LED1002,
LED1003) will go ON.
LED1003) will go ON.
4) Adjust the sensor output, and store the number of punch holes.
Chap05.p65
3/28/01, 12:11 PM
6
5-7
CHAPTER 5 TROUBLESHOOTING
2000 2000 2000 2000
CANON SADDLE FINISHER G1 REV.0 MAR. 2001
Chap05.p65
3/28/01, 12:11 PM
7
5-8
CHAPTER 5 TROUBLESHOOTING
COPYRIGHT © 2001 CANON INC.
2000 2000 2000 2000
CANON SADDLE FINISHER G1 REV.0 MAR. 2001
2 Arrangement of Electric Components
2.1 Finisher/Saddle Unit
2.1.1 Sensors, Microswitches, and Clutch
PI1
PI2
PI3
PI15
PI5
PI10
PI11
PI12
CL1
PI7
PI9
PI8
PI6
MS2
MS3
MS1
PI13
PI14
PI17
PI16
PI4
PI22
PI23
PI19
PI20
PI21
PI18
PI24
F05-201-01
Chap05.p65
3/28/01, 12:11 PM
8
