Sharp AR-PN1 Service Manual ▷ View online
3-29
CHAPTER 3 MECHANICAL SYSTEMS
COPYRIGHT © 2001 CANON INC.
2000 2000 2000 2000
CANON SADDLE FINISHER G1 REV.0 MAR. 2001
4) Push up the safety guide [4] from below
to free one side of the safety guide [4]
from the shaft [5].
from the shaft [5].
F03-102-46
5) Push up the safety guide [4] from below
to free the safety guide [4] from the
shaft [5].
shaft [5].
F03-102-47
6) Remove the paddle [6] in the direction
of the arrow.
7) Likewise, remove the other paddle.
F03-102-48
[4]
[5]
[4]
[5]
[1]
Chap03.p65
3/28/01, 12:09 PM
29
3-30
CHAPTER 3 MECHANICAL SYSTEMS
COPYRIGHT © 2001 CANON INC.
2000 2000 2000 2000
CANON SADDLE FINISHER G1 REV.0 MAR. 2001
1.2.12 Removing the Stack delivery roller (lower)/Delivery Belt
1) Remove paddle assembly, and separate
it from the processing tray assembly.
(See 1.2.4.)
(See 1.2.4.)
2) Slide the aligning plate (front) [2] and
the aligning plate (rear) [3] of the pro-
cessing tray assembly [1] by sliding
them to the outside.
cessing tray assembly [1] by sliding
them to the outside.
F03-102-49
3) Remove the processing tray stopper [4].
F03-102-50
4) Remove the screw [5], and detach the
paper guide (front) [7] while freeing the
two claws [6].
two claws [6].
F03-102-51
[1]
[3]
[2]
[4]
[5]
[7]
[6]
Chap03.p65
3/28/01, 12:09 PM
30
3-31
CHAPTER 3 MECHANICAL SYSTEMS
COPYRIGHT © 2001 CANON INC.
2000 2000 2000 2000
CANON SADDLE FINISHER G1 REV.0 MAR. 2001
5) Remove the screw [8]; then, while free-
ing the claw [9], detach the paper guide
(rear) [10].
(rear) [10].
F03-102-52
6) Remove the two stop rings [11]; then,
move the two bushings [12] to the in-
side.
side.
F03-102-53
7) Remove the four screws [13]; then, lift
the stack delivery roller assembly
(lower) [14] to detach.
(lower) [14] to detach.
F03-102-54
[8]
[10]
[9]
[11]
[11]
[12]
[12]
[14]
[13]
[13]
Chap03.p65
3/28/01, 12:09 PM
31
3-32
CHAPTER 3 MECHANICAL SYSTEMS
COPYRIGHT © 2001 CANON INC.
2000 2000 2000 2000
CANON SADDLE FINISHER G1 REV.0 MAR. 2001
8) Remove the stack delivery roller (lower)
[15] and the two delivery belts [16].
F03-102-55
Be sure to mount them so that
the edges [17] of the claws of
the delivery belts are flush.
the edges [17] of the claws of
the delivery belts are flush.
F03-102-56
1.3 PCBs
1.3.1 Removing the Finisher Controller PCB
1) Remove the rear cover. (See 1.1.3.)
2) Disconnect the 17 connectors [1], and
2) Disconnect the 17 connectors [1], and
remove the screw [2].
3) Free the PCB retainer [3], and detach
the finisher controller PCB [4].
F03-103-01
[16]
[15]
[17]
[2]
[1]
[1]
[4]
[1]
[3]
Chap03.p65
3/28/01, 12:09 PM
32
Click on the first or last page to see other AR-PN1 service manuals if exist.