Sharp AR-M351U / AR-M451U (serv.man17) Service Manual ▷ View online
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 69
Operation/Procedure
1) Select YES/NO of hard disk (the system area excluded) for-
mat.
2) Press [START] key.
During formatting, "EXECUTING" is displayed. When formatting is
completed normally, "OK" is displayed. If not, "NG" is displayed.
completed normally, "OK" is displayed. If not, "NG" is displayed.
Operation/Procedure
1) Select YES/NO of deleting the job complete list.
2) Press [START] key.
During formatting, "EXECUTING" is displayed. When formatting is
completed normally, "OK" is displayed. If not, "NG" is displayed.
completed normally, "OK" is displayed. If not, "NG" is displayed.
NOTE: When executed, this function also deletes the complete
queues of E-MAIL, FAX and IFAX, reservation data associ-
ated with the image send function, bulletin board data, and
confidential data.
ated with the image send function, bulletin board data, and
confidential data.
Operation/Procedure
1) Select YES/NO of deleting the document filing data.
2) Press [START] key.
During formatting, "EXECUTING" is displayed. When formatting is
completed normally, "OK" is displayed. If not, "NG" is displayed.
completed normally, "OK" is displayed. If not, "NG" is displayed.
NOTE: When executed, this function internally executes the same
function as SIM66-10;deleting reservation data, bulletin
board data, and confidential data.
board data, and confidential data.
62-8
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to format the hard disk (the system area
excluded). (Only in the model with a disk installed)
excluded). (Only in the model with a disk installed)
Section
MFP controller (HDD)
Item
Clear
1
YES
Execution
2
NO
Cancel
Completion
Press [CUSTOM SETTINGS] key.
62-10
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to delete a job complete list (also to delete
job log data) (Only in the model with a disk
installed)
job log data) (Only in the model with a disk
installed)
Section
MFP controller (HDD)
Item
Clear
1
YES
Execution
2
NO
Cancel
SIMULATION 62-8
HDD FORMAT (EXCEPT SYSTEM AREA).
ARE YOU SURE?
1.YES
2.NO
1
SIMULATION 62-8
HDD FORMAT (EXCEPT SYSTEM AREA). EXECUTING···.
Press [START] key.
SIMULATION 62-8
HDD FORMAT (EXCEPT SYSTEM AREA).. OK. (or NG)
Completion
Press [CUSTOM SETTINGS] key.
62-11
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to delete document filing data. (The
management area (standard folder, user folder) is
cleared.) (Only in the model with a disk installed)
management area (standard folder, user folder) is
cleared.) (Only in the model with a disk installed)
Section
MFP controller (HDD)
Item
Clear
1
YES
Execution
2
NO
Cancel
Completion
Press [CUSTOM SETTINGS] key.
SIMULATION 62-10
JOB COMPLETE DATA CLEAR. (WITH JOB LOG DATA)
ARE YOU SURE?
1.YES
2.NO
1
SIMULATION 62-10
JOB COMPLETE DATA CLEAR. (WITH JOB LOG DATA)
EXECUTING···.
Press [START] key.
SIMULATION 62-10
JOB COMPLETE DATA CLEAR. (WITH JOB LOG DATA)
OK. (or NG)
SIMULATION 62-11
DOCUMENT FILING DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 62-11
DOCUMENT FILING DATA CLEAR. EXECUTING···.
Press [START] key.
SIMULATION 62-11
DOCUMENT FILING DATA CLEAR.
OK. (or NG)
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 70
Operation/Procedure
Operation/Procedure
1) Enter the number corresponding to the shading mode to be
executed.
2) Press [START] key.
During execution, "EXECUTING" is displayed. When execution is
completed normally, "COMPLETED" is displayed.
completed normally, "COMPLETED" is displayed.
Operation/Procedure
1) Enter 1 with 10-key.
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [START] key.
When a shading error occurs, this adjustment value is
changed.
changed.
63
63-1
Purpose
Adjustment/Setup/Operation data output/Check
(Display/Print)
(Display/Print)
Function
(Purpose)
(Purpose)
Used to check the result of shading correction.
(The shading correction data are displayed.)
(The shading correction data are displayed.)
Section
Optical (Image scanning)
Item
Operation
CCD data
Values
Description
ODD GAIN
Od pixel gain adjustment value
EVEN GAIN
Even pixel gain adjustment value
MAX
All pixel MAX
MIN
All pixel MIN
AVE
All pixel average
OFFSET
All offset
CIS data : Only when DSPF installed
Values
Description
GAIN
Gain adjustment value
MAX
Pixel MAX
MIN
Pixel MIN
AVE
Pixel average
OFFSET
Black offset
DEV
Standard deviation
63-2
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to execute shading.
Section
Optical (Image scanning)
Item
Operation
1
OC SHADING
OC analog level correction and shading
correction (Document table mode)
correction (Document table mode)
2
DSPF SHADING
DSPF analog level correction and
shading correction
shading correction
SIMULATION 63-1
SHADING DATA DISPLAY.
(CCD)
ODD GAIN:
128
EVEN GAIN:
128
OFFSET:
126
MAX.:
128
MIN.:
128
AVE.:
128
(CIS)
GAIN:
128
OFFSET:
128
MAX.:
128
MIN.:
128
AVE.:
128
DEV.:
128
Completion
Press [CUSTOM SETTINGS] key.
63-7
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the white plate scan start position
for shading. (Document table mode)
for shading. (Document table mode)
Section
Laser (Exposure)
Item
Operation
Item
Set range
Default
1
CCD
CCD scan
1 - 16
6
Press [START] key.
Press [CUSTOM SETTINGS] key or [START] key.
SIMULATION 63-2
SHADING EXECUTION. SELECT1-2, AND PRESS START.
1. OC SHADING
2. DSPF SHADING
1
SIMULATION 63-2
SHADING EXECUTING···.
1. OC SHADING
Press [START] key.
SIMULATION 63-2
SHADING COMPLETED.
1. OC SHADING
1
SIMULATION 63-7
SHADING POSITION ADJUSTMENT. PRESS START.
1. CCD
0
1
SIMULATION 63-7
SHADING POSITION ADJUSTMENT. INPUT VALUE 1-16, AND
PRESS START.
1. CCD
0
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 71
Operation/Procedure
(Various print patterns output) (Table 1)
1) Select PRINT PATTERN with 10-key.
2) Enter the number corresponding to the print pattern to be
printed with 10-key.
3) Press [START] key.
4) Select PRINT START with 10-key.
5) Press [START] key.
(Print condition setting in this simulation)
∗
To select paper (paper feed tray), perform the following proce-
dures.
dures.
1) Select TRAY SELECT with 10-key.
2) Press [START] key.
3) Enter the number corresponding to the paper feed tray of the
target paper with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
∗
To adjust the print density, perform the following procedures.
1) Select DENSITY with 10-key.
2) Enter the adjustment value with 10-key.
3) Press [START] key.
∗
To set the print quantity, perform the following procedures.
1) Select MULTI with 10-key.
2) Enter the print quantity with 10-key.
3) Press [START] key.
∗
To set the print quality mode, perform the following procedures.
1) Select MODE with 10-key.
2) Enter the number corresponding to the print quality mode with
10-key.
3) Press [START] key.
∗
To set the print level, perform the following procedures.
1) Select LEVEL with 10-key.
2) Enter the adjustment value with 10-key.
3) Press [START] key.
NOTE: In some print patterns, changing the level may not change
the picture quality.
∗
To set duplex/simplex print, perform the following procedures.
1) Select DUPLEX with 10-key.
2) Enter the number corresponding to the operation mode with
10-key.
3) Press [START] key.
(Table 1)
(Note 1) Print pattern
64
64-1
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operation of the printer section
(self-print operation), (The print pattern, the paper
feed mode, the print mode, the print quantity, and
the density can be optionally set.)
(self-print operation), (The print pattern, the paper
feed mode, the print mode, the print quantity, and
the density can be optionally set.)
Item
Operation
0
TRAY SELECT
1. TRAY1
2. TRAY2
3. TRAY3
4. TRAY4
5. BPT
2. TRAY2
3. TRAY3
4. TRAY4
5. BPT
Paper feed tray
1: Tray 1
2: Tray 2
3: Tray 3
4: Tray 4
5: Manual feed
2: Tray 2
3: Tray 3
4: Tray 4
5: Manual feed
1
PRINT START
Print execution (Printing of the set
data is executed.)
data is executed.)
2
PRINT PATTERN
Print pattern (Note 1)
3
DENSITY
Graphic density (Valid only when
No. 79, 80 or 84 is selected.)
No. 79, 80 or 84 is selected.)
4
MULTI
Print quantity
5
MODE
1. STANDARD
2. SMOOTHING
3. TONER SAVE
4. HALF TONE
5. SMOOTHING + TONER
2. SMOOTHING
3. TONER SAVE
4. HALF TONE
5. SMOOTHING + TONER
SAVE
6. SMOOTHING + HALF TONE
7. TONER SAVE + HALF
7. TONER SAVE + HALF
TONE
8. SMOOTHING + TONER
SAVE + HALF TONE
Print mode
1. Standard
2. Smoothing ON
3. Smoothing ON
3. Toner save ON
4. Half tone ON
5. Smoothing + toner save
6. Smoothing + half tone
7. Toner save + half tone
8. Smoothing + toner save +
2. Smoothing ON
3. Smoothing ON
3. Toner save ON
4. Half tone ON
5. Smoothing + toner save
6. Smoothing + half tone
7. Toner save + half tone
8. Smoothing + toner save +
half tone
6
LEVEL
(Parameter of print image
process)
process)
7
DUPLEX
1. NO
2. YES
2. YES
Duplex
0: NO (Simplex)
1: YES (Duplex)
1: YES (Duplex)
No
Engine
pattern
pattern
Controller
Pattern
Note
1
❍
For off-center adjustment
2
❍
Main scanning direction 1 by 5
3
❍
Main scanning direction 1mm-
pitch
pitch
4
❍
Main scanning direction 3 by 3
5
❍
Sub scanning direction 1 by 1
6
❍
Sub scanning direction 1 by 5
7
❍
Sub scanning direction 2 by 4
8
❍
Sub scanning direction 3 by 3
9
❍
Right oblique 1 by 2
10
❍
Right oblique 1 by 5
11
❍
Right oblique 2 by 4
12
❍
Right oblique 3 by 3
13
❍
Left oblique 1 by 2
14
❍
Left oblique 1 by 5
15
❍
Left oblique 2 by 4
16
❍
Left oblique 3 by 3
17
❍
Dot 1 by 1
18
❍
Dot 3 by 3
19
❍
Dot
20
❍
Solid black
21
❍
Main scanning direction 1 by 1
22
❍
Main scanning direction 5 by 1
23
❍
Main scanning direction 4 by 2
24
❍
Main scanning direction 3 by 3
25
❍
Sub scanning direction 1 by 1
26
❍
Sub scanning direction 5 by 1
27
❍
Sub scanning direction 4 by 2
28
❍
Sub scanning direction 3 by 3
29
❍
Right oblique 2 by 1
30
❍
Right oblique 5 by 1
31
❍
Right oblique 4 by 2
32
❍
Right oblique 3 by 3
33
❍
Left oblique 2 by 1
34
❍
Left oblique 5 by 1
35
❍
Left oblique 4 by 2
36
❍
Left oblique 3 by 3
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 72
❏
: Error diffusion process
Note*: Since the "DENSITY" of an actual copy or printer output
differs, they differ from the output of self print.
37
❍
Dot 1 by 1
38
❍
Dot 3 by 3
39
❍
Dot
40
❍
Solid white
50
❍
All surface 1 by 1 (Vertical)
51
❍
All surface 1 by 1 (Horizontal)
52
❍
All surface 1 by 2 (Vertical)
53
❍
All surface 1 by 2 (Horizontal)
54
❍
All surface 1 by 3 (Vertical)
55
❍
All surface 1 by 3 (Horizontal)
56
❍
All surface 1 by 4 (Vertical)
57
❍
All surface 1 by 4 (Horizontal)
58
❍
All surface 1 by 5 (Vertical)
59
❍
All surface 1 by 5 (Horizontal)
60
❍
All surface 2 by 2 (Vertical)
61
❍
All surface 2 by 2 (Horizontal)
62
❍
All surface 2 by 3 (Vertical)
63
❍
All surface 2 by 3 (Horizontal)
64
❍
All background
65
❍
Special pattern
66
❏
For every other 1 block width
128 pixels/ 32 gradations
128 pixels/ 32 gradations
67
❏
For every other 1 block width
128 pixels/ 16 gradations
128 pixels/ 16 gradations
68
❏
For every other 1 block width
128 pixels/ 8 gradations
128 pixels/ 8 gradations
69
❍
1-dot pattern
70
❍
Print adjustment pattern with
scale (Vertical)
scale (Vertical)
71
❍
Grid pattern
72
❍
Slant line 45 degrees
73
❍
Slant line 26.6 degrees
74
❍
Slant line 63.4 degrees
75
❍
ID/BG pattern
76
❍
Dot pattern 12.5%
77
❍
Dot pattern 28%
78
❍
Dot pattern 50%
79
❏
All surface effort diffusion
background
background
80
❍
All surface dither process
background
background
81
❍
For every other 1 block width
128 pixels/ 32 gradations
128 pixels/ 32 gradations
82
❍
For every other 1 block width
128 pixels/ 16 gradations
128 pixels/ 16 gradations
83
❍
For every other 1 block width
128 pixels/ 8 gradations
128 pixels/ 8 gradations
84
❍
Memory check pattern
85
❍
Cleaning check pattern
86
❍
Offset check pattern
87
❍
Text pattern A
Note *
88
❍
Text pattern B
Note *
89
❍
Text pattern C
Note *
90
Toner quantity measuring
chart
chart
91
Radiation chart
98
Data printing
No
Engine
pattern
pattern
Controller
Pattern
Note
Select 1, and
press [START] key.
press [START] key.
Select other than 1, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
SIMULATION 64-1
SELF PRINT MODE. SELECT 0-7, AND PRESS START.
0. TRAY SELECT :
1
1. PRINT START
2. PRINT PATTERN:
87
3. DENSITY :
1
4. MULTI :
1
5. MODE :
1
6. LEVEL :
1
7. DUPLEX :
1
1
SIMULATION 64-1
SELF PRINT MODE. INPUT VALUE, AND PRESS START.
(PRINT PATTERN)
INPUT 1-98.
71
SIMULATION 64-1
SELF PRINT MODE. INPUT VALUE, AND PRESS START.
(DENSITY)
1-255
100
SIMULATION 64-1
SELF PRINT MODE. INPUT VALUE, AND PRESS START.
(MULTI COUNT)
1-999
1
SIMULATION 64-1
SELF PRINT MODE. SELECT 1-8, AND PRESS START.
(MODE)
1.STANDARD 2.SMOOTHING 3.TONER SAVE 4.HALF TONE
5.SMOOTHING+ TONER SAVE 6.SMOOTHING+ HALF TONE
7.TONER SAVE+ HALF TONE
8.SMOOTHING+ TONER SAVE+ HALF TONE
1
3
SIMULATION 64-1
SELF PRINT MODE. SELECT 1-5, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
1
SIMULATION 64-1
SELF PRINT MODE. SELECT 1-2, AND PRESS START.
(DUPLEX)
1.NO 2.YES
1
SIMULATION 64-1
SELFT PRINT MODE.. EXECUTING···
0. TRAY SELECT :
1
2. PRINT PATTERN:
87
3. DENSITY :
1
4. MULTI :
1
5. MODE :
1
6. LEVEL :
1
7. DUPLEX :
1
0
(3)
(2)
(4)
(5)
(6)
(0)
(7)
SIMULATION 64-1
SELF PRINT MODE. INPUT VALUE, AND PRESS START.
(LEVEL)
1-5
Click on the first or last page to see other AR-M351U / AR-M451U (serv.man17) service manuals if exist.