Sharp AR-M351U / AR-M451U (serv.man17) Service Manual ▷ View online
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 81
Operation/Procedure
1) Select YES/NO of data transfer.
2) Press [START] key.
Operation/Procedure
1) Enter the number corresponding to the information (item) to be
printed with 10-key.
2) Press [START] key.
Operation/Procedure
1) Enter the number corresponding to the volume with 10-key.
2) Press [START] key.
Selection of 1, 2, and 3 can be made during execution.
Operation/Procedure
1) Turn OFF the power.
2) Remove the protect pin.
3) Turn ON the power.
4) Enter the SIM 66-23 mode.
5) Press [START] key.
During operation, "EXECUTING" is displayed. When the operation
is completed normally, "COMPLETE" is displayed.
is completed normally, "COMPLETE" is displayed.
If an error occurs, "FAIL" is displayed.
6) Turn OFF the power, and attach the protect pin.
66-20
Purpose
Data transfer
Function
(Purpose)
(Purpose)
Used to read the back-up data by SIM 66-19 to the
SRAM/HDD. (Only when FAX is installed)
SRAM/HDD. (Only when FAX is installed)
Section
FAX
Item
Data
1
YES
Backup is executed.
2
NO
Backup is not executed.
66-21
Purpose
Adjustment/Setup/Operation data output/Check
(Display/Print)
(Display/Print)
Function
(Purpose)
(Purpose)
Used to print information related to FAX (various
registrations, communication management, file
management, system error protocol). (Only when
FAX is installed)
registrations, communication management, file
management, system error protocol). (Only when
FAX is installed)
Section
FAX
Item
Data
1
REGISTERED
Various registration information
2
MANAGEMENT
Communication management
information
information
3
FILE MANAGEMENT
File management information
4
SYSTEM ERROR
System error information
5
PROTOCOL
Protocol information
SIMULATION 66-20
ADDRESS DATA BACK UP. (READ FROM FLASH ROM)
ARE YOU SURE?
1. YES
2. NO
SIMULATION 66-20
ADDRESS DATA BACK UP. (READ FROM FLASH ROM) EXECUTING...
1
1
Press [START] key.
After completion of read
SIMULATION 66-21
FAX INFORMATION PRINT OUT. SELECT 1-5, AND PRESS START.
1. REGISTERED 2. MANAGEMENT
3. FILE MANAGEMENT 4. SYSTEM ERROR
5. PROTOCOL
(When 1)
SIMULATION 66-21
FAX INFORMATION PRINT OUT. EXECUTING···
1. REGISTERED
If there is no print data,
the display returns to the
original state without printing.
the display returns to the
original state without printing.
Select other than 0 and
press [START] key.
press [START] key.
After completion of backup
66-22
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to adjust the handset volume. (Only when
the FAX is installed.)
the FAX is installed.)
Section
FAX
Item
Operation
1
MIN
Small
2
MIDDLE
Medium
3
MAX
Large
Same display
Select 3 and press [START] key.
66-23
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to download the FAX program. (Only when
FAX is installed)
Not used in the market. (For development)
FAX is installed)
Not used in the market. (For development)
Section
FAX
Item
SIMULATION 66-22
HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START.
1. MIN
2. MIDDLE
3. MAX
2
SIMULATION 66-22
HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START.
EXECUTING···.
1. MIN
2. MIDDLE
3. MAX
2
Press [CUSTOM SETTINGS] key.
Press [START] key.
SIMULATION 66-22
HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START.
EXECUTING···.
1. MIN
2. MIDDLE
3. MAX
3
SIMULATION 66-22
HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START.
1. MIN
2. MIDDLE
3. MAX
3
Press [CUSTOM SETTINGS] key.
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 82
Operation/Procedure
1) Select YES/NO of data clear.
2) Press [START] key.
Operation/Procedure
1) Enter the Modem dial-in FAX number (1 - 9, 0, *, #) with 10-
key.
2) Press [START] key.
Operation/Procedure
1) Enter the Modem dial-in FAX number (1 - 9, 0, *, #) with 10-
key.
2) Press [START] key.
Operation/Procedure
1) Enter the voice warp transfer number (1 - 9, 0, *, #) with 10-
key.
2) Press [START] key.
Operation/Procedure
1) Select YES/NO of data clear.
2) Press [START] key.
Press [START] key.
After failing of writing
66-24
Purpose
Clear
Function
(Purpose)
(Purpose)
Used to clear the FAST memory data. (Only when
FAX is installed)
FAX is installed)
Section
FAX
Item
Data
1
YES
FAST memory data is cleared.
2
NO
Not cleared.
66-25
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to register the FAX number for Modem dial-
in. (Only when FAX is installed)
Not used in the market. (For development)
in. (Only when FAX is installed)
Not used in the market. (For development)
Section
FAX
Item
Data
SIMULATION 66-23
FAX PROGRAM DOWNLOAD.
EJECT PROTECT PIN, AND PRESS START.
SIMULATION 66-23
FAX PROGRAM DOWNLOAD. EXECUTING···
SIMULATION 66-23
FAX PROGRAM DOWNLOAD.
COMPLETE
POWER OFF, AND SET PROTECT PIN
After completion of writing
SIMULATION 66-23
FAX PROGRAM DOWNLOAD.
FAIL
CHECK PROTECT PIN
SIMULATION 66-24
FAST MEMORY DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
SIMULATION 66-25
M-D-IN FAX NUMBER SETTING. 0-9:[0-9],*:[*],#:[#]
INPUT NUMBER AND PRESS START.
0123456789*#01234567
66-26
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to register external telephone numbers for
Modem dial-in. (Only when FAX is installed)
Not used in the market. (For development)
Modem dial-in. (Only when FAX is installed)
Not used in the market. (For development)
Section
FAX
Item
Data
66-27
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to register the transfer number for voice
warp. (Only when FAX is installed)
Not used in the market. (For development)
warp. (Only when FAX is installed)
Not used in the market. (For development)
Section
FAX
Item
Data
66-29
Purpose
Clear
Function
(Purpose)
(Purpose)
Used to clear data related to an address book
(one-touch registration, program registration/
expansion, relay memory box registration, each
table content).
(one-touch registration, program registration/
expansion, relay memory box registration, each
table content).
Section
FAX, Network scanner
Item
Data
1
YES
Address book data is cleared.
2
NO
Not cleared.
SIMULATION 66-26
M-D-IN EXTEL NUMBER SETTING. 0-9:[0-9],*:[*],#:[#]
INPUT NUMBER AND PRESS START.
0123456789*#01234567
SIMULATION 66-27
V-WP TRANSMIT NUMBER SETTING. 0-9:[0-9],*:[*],#:[#]
INPUT NUMBER AND PRESS START.
0123456789*#01234567
SIMULATION 66-29
ADDRESS DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
1
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 83
Operation/Procedure
The TEL/LIU state is displayed.
When the state is changed, it is highlighted.
Operation/Procedure
1) Enter the number corresponding to the check item with 10-
key.
2) Press [START] key.
Operation/Procedure
When check is completed normally, "OK" is displayed. In case of
an error, "NG" is displayed.
an error, "NG" is displayed.
(Display message)
Operation/Procedure
The detected signal is highlighted.
Operation/Procedure
Communication test is performed to measure the time (ms).
Send is made under the following conditions.
Operation/Procedure
1) Select YES/NO of Modem program reload.
2) Press [START] key.
When reload is completed normally, "OK" is displayed. In case of
an error, "CHECK SUM" is displayed.
an error, "CHECK SUM" is displayed.
The result of Modem reload is displayed.
66-30
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the change in the TEL/LIU status.
(Only when FAX is installed)
(Only when FAX is installed)
Section
FAX
Item
Operation
HS1
Polarity reverse signal
HS2
Polarity reverse signal
RHS
Handset hook SW
EXHS
External telephone hook SW
66-31
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the relay operation. (Only when
FAX is installed)
FAX is installed)
Section
FAX
Item
Operation
66-32
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the receive data (fixed data) from
the line. (Only when FAX is installed)
the line. (Only when FAX is installed)
Section
FAX
Item
Operation
CHECKING
Checking
OK
Checking completed (OK)
NG
Checking completed (NG)
1
SIMULATION 66-30
TEL/LIU SENSOR CHECK.
HS1 HS2
RHS
EXHS
1 0 0 0 1 1 0 0
1 2 3 4 5 6 7 8
SIMULATION 66-31
TEL/LIU SETTING.
INPUT 0-1, AND PRESS START.
1.
MPXA
2. CION 3. MR 4. EC
5.
S.
6.
CML
7. DP 8.
SIMULATION 66-32
RECEIVED DATA CHECK.
CHECKING···.(OK or NG)
66-33
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the signal (BUSY TONE/CNG/
CED/FNET/DTMF) detection. (Only when FAX is
installed)
CED/FNET/DTMF) detection. (Only when FAX is
installed)
Section
FAX
Item
Operation
66-34
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to measure the communication time of test
image data. (Only when FAX is installed)
image data. (Only when FAX is installed)
Section
FAX
Item
Operation
Communication means
Memory send
Image quality
Normal text
Density
Light
ECM
ON
Sender record
OFF
66-35
Purpose
Setting
Function
(Purpose)
(Purpose)
Modem program rewriting. (Only when FAX is
installed)
Not used in the market. (For development)
installed)
Not used in the market. (For development)
Section
FAX
Item
Data
1
YES
Modem block reload is cleared.
2
NO
Not reloaded.
COMPLETE
Reload completed
81
Check sum error
82
Write error
83
Delete error
84
Verify error
NG
Due to loader NG
SIMULATION 66-33
SIGNAL DETECT CHECK.
BUSY TONE
CNG
CED FNET DTMF
SIMULATION 66-34
COMMUNICATION TIME DISPLAY.
* * * * * ms
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 84
Operation/Procedure
1) Enter the number corresponding to the check mode with 10-
key.
2) Press [START] key.
When check is completed normally, "OK" is displayed. Incase of
an error, "NG" is displayed.
an error, "NG" is displayed.
When check is "repeat," the operation is continued until the result
is NG or [CUSTOM SETTINGS] key is pressed.
is NG or [CUSTOM SETTINGS] key is pressed.
Operation/Procedure
1) Enter the number corresponding to the destination.
2) Press [START] key.
Operation/Procedure
1) The confirmation window is displayed. Select whether rewrit-
ing of the program into PIC installed in the FAX VOX is per-
formed or not.
formed or not.
NOTE: Release the write protect notch.
FAX program writing enabled (Jumpers and DIP SW
depending on the model.)
depending on the model.)
2) Press [START] key.
When reload is completed normally, "OK" is displayed. In case of
an error, "NG" is displayed.
an error, "NG" is displayed.
NG cause:
• Write protect is set.
• PIC is not installed.
• Access error to PIC
Press [START] key.
After completion of reloading
66-36
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check interface between MFPC controller
and MDMC. (Check of the data line or the
command line) (Only when FAX is installed)
and MDMC. (Check of the data line or the
command line) (Only when FAX is installed)
Section
FAX
Item
Operation
1
MFPC
←
MDMC
Date line once only
2
MFPC
→
MDMC
Date line once only
3
MFPC
←
MDMC
Data line repeat
4
MFPC
→
MDMC
Data line repeat
5
MFPC
←
MDMC
Command line once only
6
MFPC
→
MDMC
Command line once only
7
MFPC
←
MDMC
Command line repeat
8
MFPC
→
MDMC
Command line repeat
SIMULATION 66-35
MODEM PROGRAM RELOAD.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 66-35
MODEM PROGRAM RELOAD.
EXECITOMG···
LOADER··· xxxxx
MODEM···· xxxxx
SIMULATION 66-35
MODEM PROGRAM RELOAD.
LOADER···OK
MODEM····COMPLETE
SIMULATION 66-36
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
1. MFPC<-MDMC(DATA once)
2. MFPC->MDMC(DATA once)
3. MFPC<-MDMC(DATA repeat)
4. MFPC->MDMC(DATA repeat)
5. MFPC<-MDMC(CMD once)
6. MFPC->MDMC(CMD once)
7. MDPC<-MDMC(CMD repeat)
8. MFPC->MDMC(CMD repeat)
1
SIMULATION 66-36
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
EXECUTING...(OK or NG)
SIMULATION 66-36
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
EXECUTING...
Press [START] key.
When check is "once" or
"repeat" and the result is "NG":
"repeat" and the result is "NG":
When check is "repeat" and
[CUSTOM SETTINGS] key ON:
[CUSTOM SETTINGS] key ON:
66-39
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the destination specifications. (Only
when FAX is installed)
when FAX is installed)
Section
FAX
Item
Specifications Operation
66-42
Purpose
Setting
Function
(Purpose)
(Purpose)
PIC program rewriting (Only when FAX is
installed)
installed)
Section
FAX
Item
Operation
1
YES
Execution
2
NO
Cancel
Press [START] key.
SIMULATION 66-39
FAX DESTINATION SETUP.
SELECT 1-6, AND PRESS START
0. NO DESTINATION
1. JAPAN
2. U.S.A./CANADA
3. EUROPE
4. AUSTRALIA
5. CHINA
6. ASIA
1
SIMULATION 66-42
PIC PROGRAM RELOAD.
ARE YOU SURE ?
1.YES
2.NO
1
Press [START] key.
Press [START] key.
SIMULATION 66-42
PIC PROGRAM RELOAD EXECUTING ....
Press [CUSTOM SETTINGS] key.
SIMULATION 66-42
PIC PROGRAM RELOAD
OK
Click on the first or last page to see other AR-M351U / AR-M451U (serv.man17) service manuals if exist.