Sharp AR-M351U / AR-M451U (serv.man17) Service Manual ▷ View online
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 57
Operation/Procedure
(Lead edge image loss adjustment) (Table 1)
1) Set the front and back surface image loss adjustment values
(LEAD EDGE) as specified below:
(Standard set value) Lead edge image loss: 1.5mm (LEAD:
1.5)Paper lead edge: 3.5mm (DENA: 35)
1.5)Paper lead edge: 3.5mm (DENA: 35)
∗
Set the adjustment value of LEAD to 15. (Enter 15 as the
adjustment value of LEAD EDGE, and press [P] key.)
adjustment value of LEAD EDGE, and press [P] key.)
2) Make a duplex copy at 100% with the SPF, and check that the
lead edge (image loss) is 1.5mm either on the front surface
and the back surface. (Select the duplex mode in the paper
selection mode of SIM 50-6.) (Table 3) (Enter 100 as the copy
magnification ratio set value (MAGNIFICATION), and press
[START] key.)
and the back surface. (Select the duplex mode in the paper
selection mode of SIM 50-6.) (Table 3) (Enter 100 as the copy
magnification ratio set value (MAGNIFICATION), and press
[START] key.)
If the adjustment result is not satisfactory, perform the following
procedures:
procedures:
3) Change the adjustment values of SIDE1 and SIDE2, and per-
form the adjustment. (Change the adjustment values of SIDE1
and SIDE2, and press [START] key.)
and SIDE2, and press [START] key.)
(Shift for the adjustment value change: 0.1mm/step)
(The image scan start timing is determined with the detection
timing of the document lead edge by the detector SPPD.)
timing of the document lead edge by the detector SPPD.)
Repeat procedures 2) and 3) until a satisfactory result is obtained.
(Rear edge image loss adjustment)
1) Use the SPF at 100% to make a duplex copy, and check that
the rear edge image loss is 1.5mm on the front and the back
surfaces. (Select the duplex mode in the paper selection mode
of SIM 50-6.) (Enter 100 as the copy magnification ratio set
value (MAGNIFICATION), and press [START] key.)
surfaces. (Select the duplex mode in the paper selection mode
of SIM 50-6.) (Enter 100 as the copy magnification ratio set
value (MAGNIFICATION), and press [START] key.)
If the adjustment value is not satisfactory, perform the following
procedure.
procedure.
2) Change the adjustment value of TRAIL EDGE. Change the
adjustment value of TRAIL EDGE, and press [START] key.
Repeat the above procedures until a satisfactory result is
obtained.
obtained.
(Front/rear frame direction image loss adjustment)
Set the adjustment value of the front surface and the back surface
(FRONT/REAR) to 20. (Enter 20 as the adjustment value of
FRONT/REAR, and press [P] key.)
(FRONT/REAR) to 20. (Enter 20 as the adjustment value of
FRONT/REAR, and press [P] key.)
When the adjustment value is changed, the image position is
shifted in the front/rear frame direction.
shifted in the front/rear frame direction.
NOTE: When [P] key is pressed after entering the adjustment
value, the adjustment value is set. When [START] key is
pressed instead, the adjustment value is set and copying is
performed. (Table 2)
pressed instead, the adjustment value is set and copying is
performed. (Table 2)
(Copy condition setting in this simulation)
∗
To select paper (paper feed tray), perform the following proce-
dures.
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key. (Table 3)
4) Press [START] key. (The paper feed tray is selected.)
∗
To set the copy magnification ratio, perform the following proce-
dure.
dure.
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
(Table 1)
(Table 2)
(Table 3)
When the total of the above set value and 10 is entered, the mode
is changed to the duplex mode (DD), and a duplex copy is made.
is changed to the duplex mode (DD), and a duplex copy is made.
50-6
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the copy image position and void
area (image loss) on print paper in the copy mode.
(The similar adjustment can be performed with
SIM 50-7 (simple method).) (SPF mode)
area (image loss) on print paper in the copy mode.
(The similar adjustment can be performed with
SIM 50-7 (simple method).) (SPF mode)
Item
Picture quality
SIDE1: SPF front surface document lead edge scan position
adjustment value
SIDE2: SPF back surface document lead edge scan position
adjustment value
Set range
25 - 200 (%)
Item
Set
range
Default
0
TRAY SELECT
Paper feed tray
selection
selection
1 - 5
–
1
COPY START
Copy START (Default)
–
–
2
MAGNIFICATION Print magnification ratio
25 -
200%
–
(Lead edge adjustment value)
3
SIDE1
Front surface document
scan start position
adjustment value
scan start position
adjustment value
0 - 99
50
4
SIDE2
Back surface document
scan start position
adjustment value
scan start position
adjustment value
(Image loss set value: SIDE 1)
5
LEAD_EDGE
Front surface lead edge
image loss set value
image loss set value
0 - 99
15
6
FRONT_REAR
Front surface side edge
image loss set value
image loss set value
20
7
TRAIL_EDGE
Front surface rear edge
image loss set value
image loss set value
0 - 20
0
(Image loss set value: SIDE 2)
8
LEAD_EDGE
Back surface lead edge
image loss set value
image loss set value
0 - 99
15
9
FRONT/REAR
Back surface side edge
image loss set value
image loss set value
20
10 TRAIL_EDGE
Back surface rear edge
image loss set value
image loss set value
0 - 20
0
Normal display
NOW COPYING.
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
TRAY1
2
TRAY2
TRAY2
3
TRAY3
TRAY3
4
TRAY4
TRAY4
5
BPT
Manual feed
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 58
Operation/Procedure
(Lead edge image loss adjustment)
1) Set the front and back surface image loss adjustment values
(LEAD EDGE) as specified below:
(Standard set value) Lead edge image loss: 1.5mm (LEAD:
1.5)Paper lead edge void: 3.5mm (DENA: 35)
1.5)Paper lead edge void: 3.5mm (DENA: 35)
∗
Set the adjustment value of LEAD to 15. (Enter 15 as the
adjustment value of LEAD EDGE, and press [P] key.)
adjustment value of LEAD EDGE, and press [P] key.)
2) Set the adjustment value of L4 to 0. (Enter 0 as the adjustment
value of L4, and press [P] key.
3) Set the adjustment value of L5 to 0. (Enter 0 as the adjustment
value of L5, and press [P] key.
4) Make a copy at 200% with the SPF, and calculate the values
of L4 and L5. (Enter 200 as the set value of the copy magnifi-
cation ratio set value (MAGNIFICATION) and press [START]
key.)
cation ratio set value (MAGNIFICATION) and press [START]
key.)
5) Enter the above values as the set values of L4 and L5. (Enter
the adjustment values of L4 and L5, and press [P] key.)
(The image scan start timing is determined with the detection
timing of the document lead edge by the detector SPPD.)
timing of the document lead edge by the detector SPPD.)
If the adjustment result is not satisfactory, perform the above pro-
cedures again or adjust with SIM 50-1.
cedures again or adjust with SIM 50-1.
NOTE: If the adjustment result of the above procedures is not sat-
isfactory, though the adjustment value is changed individu-
ally, the adjustment cannot be completed normally.
ally, the adjustment cannot be completed normally.
Repeat procedures 2) - 6) until a satisfactory result is obtained.
(Rear edge image loss adjustment)
Adjust so that the rear edge image loss is 3.5mm. (Change the
adjustment value of TRAIL EDGE, and press [START] key.)
adjustment value of TRAIL EDGE, and press [START] key.)
(Front/rear frame direction image loss adjustment)
Set the adjustment value of SIDE to 20. (Enter 20 as the adjust-
ment value of SIDE, and press [P] key.)
ment value of SIDE, and press [P] key.)
When the adjustment value is changed, the image position is
shifted in the front/rear frame direction.
shifted in the front/rear frame direction.
NOTE: When [P] key is pressed after entering the adjustment
value, the adjustment value is set. When [START] key is
pressed instead, the adjustment value is set and copying is
performed. (Table 2)
pressed instead, the adjustment value is set and copying is
performed. (Table 2)
(Copy condition setting in this simulation)
∗
To select paper (paper feed tray), perform the following proce-
dures.
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key. (Table 3)
4) Press [START] key. (The paper feed tray is selected.)
∗
To set the copy magnification ratio, perform the following proce-
dure.
dure.
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
Select 2, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
50
1
2
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). SELECT 0-10, AND PRESS
START.
0.TRAY SELECT
1
1.COPY START
2.MAGNIFICATION
100
(ADJUSTMENT DATA)3.SIDE1
50
4.SIDE2
50
(IMAGE LOSS SETTING)
SIDE1: 5.LEAD_EDGE
15
6.FRONT/REAR
20
7.TRAIL_EDGE
0
SIDE2: 8.LEAD_EDGE
15
9.FRONT/REAR
20
10.TRAIL_EDGE
0
Press [CUSTOM SETTING] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
Press [START] key or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). INPUT VALUE 0-99, AND PRESS
START.
3.SIDE1
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). NOW COPYING.
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). SELECT 1-15, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
(ABOVE+10: DUPLEX MODE)
Select 1,
and press
[START] key.
and press
[START] key.
Select 0, and press [START] key.
Select other than 0 - 2, and press [START] key.
100
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF).
(MAGNIFICATION)
INPUT 25-200(%)
50-7
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the copy image position and void
area (image loss) on print paper in the copy mode.
(The similar adjustment can be performed with
SIM 50-6.) (SPF mode)
area (image loss) on print paper in the copy mode.
(The similar adjustment can be performed with
SIM 50-6.) (SPF mode)
Item
Picture quality
L4 = Distance (mm) from the image lead edge position to the
scale of 10mm x 10
L5 = Distance (mm) from the image lead edge position to the
paper lead edge x 10
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 59
4) Press [START] key.
(Table 1)
(Table 2)
(Table 3)
When the total of the above set value and 10 is entered, the mode
is changed to the duplex mode (DD), and a duplex copy is made.
is changed to the duplex mode (DD), and a duplex copy is made.
Operation/Procedure
(Print image off-center position adjustment)
NOTE: This simulation cannot provide an accurate adjustment. Do
not use.
1) Enter the number corresponding to the number of the paper
feed tray to be adjusted with 10-key. (Select one of 3 - 9.)
Set range
25 - 200 (%)
Item
Set
range
Default
0
TRAY SELECT
Paper feed tray
selection
selection
1 - 5
–
1
COPY START
Copy START (Default)
–
–
2
MAGNIFICATION Print magnification
ratio
25 -
200%
–
(Lead edge adjustment value)
3
L4
Distance from the
front surface image
lead edge to the scale
of 10mm (SPF: 200%)
front surface image
lead edge to the scale
of 10mm (SPF: 200%)
0 - 999
–
4
L5
Distance from the
back surface image
lead edge to the scale
of 10mm (SPF: 200%)
back surface image
lead edge to the scale
of 10mm (SPF: 200%)
–
(Image loss set value: SIDE 1)
5
LEAD_EDGE
Front surface lead
edge image loss set
value
edge image loss set
value
0 - 99
15
6
FRONT_REAR
Front surface side
edge image loss set
value
edge image loss set
value
20
7
TRAIL_EDGE
Front surface rear
edge image loss set
value
edge image loss set
value
0 - 20
0
(Image loss set value: SIDE 2)
8
LEAD_EDGE
Back surface lead
edge image loss set
value
edge image loss set
value
0 - 99
15
9
FRONT/REAR
Back surface side
edge image loss set
value
edge image loss set
value
20
10 TRAIL_EDGE
Back surface rear
edge image loss set
value
edge image loss set
value
0 - 20
0
Normal display
NOW COPYING.
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
TRAY1
2
TRAY2
TRAY2
3
TRAY3
TRAY3
4
TRAY4
TRAY4
5
BPT
Manual feed
Select 2, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
50-10
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the print image off-center position.
(Adjusted separately for each paper feed section.)
(Adjusted separately for each paper feed section.)
Item
Picture quality
Image position
Item
Set range Default
0 TRAY SELECT
Paper feed tray
selection
selection
1 - 5
–
1 COPY START
Copy START (Default)
–
–
2 MAGNIFICATION Print magnification
ratio
25 - 400%
100
(Off-center adjustment value)
3 TRAY1
Tray 1 adjustment
0 - 99
50
4 TRAY2
Tray 2 adjustment
5 TRAY3
Tray 3 adjustment
6 TRAY4
Tray 4 adjustment
7 BPT
Manual feed tray
adjustment
adjustment
8 ADU
Adjustment when
paper is fed again
from ADU
paper is fed again
from ADU
50
1
2
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 0-10, AND PRESS
START.
0.TRAY SELECT
1
1.COPY START
2.MAGNIFICATION
200
(ADJUSTMENT DATA) 3.L4
160
4.L5
160
(IMAGE LOSS SETTING)
SIDE1: 5.LEAD_EDGE
15
6.FRONT/REAR
20
7.TRAIL_EDGE
0
SIDE2: 8.LEAD_EDGE
15
9.FRONT/REAR
20
10.TRAIL_EDGE
0
Press [CUSTOM SETTING] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
Press [START] key or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). INPUT VALUE 0-99, AND
PRESS START.
3.L4
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). NOW COPYING.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 1-15, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
Select 1,
and press
[START] key.
and press
[START] key.
Select 0, and press [START] key.
Select other than 0 - 2, and press [START] key.
100
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.).
(MAGNIFICATION)
INPUT 25-200(%)
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 60
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [P] key or [START] key. When [START] key is pressed,
the adjustment value set and copying is performed.
(Image off-center adjustment)
1) Enter 1 with 10-key.
2) Press [START] key. The adjustment pattern is printed.
3) Check the off-center of the printed image.
(UNIT: 0.1mm/step When the adjustment value is increased,
the print image is shifted to the front direction.)
the print image is shifted to the front direction.)
NOTE: This adjustment can be performed with SIM 50-5.
(Copy condition setting in this simulation)
∗
To select paper (paper feed tray), perform the following proce-
dures.
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key. (Select one of 1 - 5)
4) Press [START] key. (The paper feed tray is selected.)
When the total of the above set value (1 - 5) and 10 is entered, the
mode is changed to the duplex print mode.
mode is changed to the duplex print mode.
∗
To set the copy magnification ratio, perform the following proce-
dure.
dure.
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
NOTE: When [P] key is pressed after entering the adjustment
value in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
[START] key is pressed, the adjustment value is set and
copying is performed.
Operation/Procedure
(Select the scan mode to be adjusted.)
1) Enter the number corresponding to the scan mode to be
adjusted with 10-key. (Select one of 3 - 5.)
2) Press [START] key.
Normal display
NOW COPYING.
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
TRAY1
2
TRAY2
TRAY2
3
TRAY3
TRAY3
4
TRAY4
TRAY4
5
BPT
Manual feed
Set range
25 - 400 (%)
Select 0, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
50-12
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the scan image off-center position.
(Adjusted separately for each scan mode.)
(Adjusted separately for each scan mode.)
Section
Item
Picture quality
Image position
Item
Set range
Default
0 TRAY SELECT
Paper feed tray
selection
selection
1 - 5
–
1 COPY START
Copy START
(Default)
(Default)
–
–
2 MAGNIFICATION Print magnification
ratio
25 - 400%
100
(Resist adjustment value)
3 PLATEN
OC mode
adjustment
adjustment
0 - 99
50
4 SPF SIDE1
SPF front surface
adjustment
adjustment
5 SPF SIDE2
SPF back surface
adjustment
adjustment
50
2
Select 1,
and press
[START] key.
and press
[START] key.
Select other than 0 - 2, and
press [START] key.
press [START] key.
Press [CUSTOM SETTINGS] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 0-8, AND PRESS
START.
0.TRAY SELECT
1
1.COPY START
2.MAGNIFICATION
100
(ADJUSTMENT DATA)
3.TRAY1
50
4.TRAY2
50
5.TRAY3
50
6.TRAY4
50
7.BPT
50
8.ADU
50
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. NOW COPYING.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND
PRESS START.
2.TRAY1
1
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 1-15, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
(ABOVE+10: DUPLEX MODE)
Click on the first or last page to see other AR-M351U / AR-M451U (serv.man17) service manuals if exist.