Sharp AR-M351U / AR-M451U (serv.man17) Service Manual ▷ View online
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 73
Operation/Procedure
Touch the four cross marks (+) sequentially. The coordinates of
pressed positions are set.
pressed positions are set.
When the coordinates setting is completed normally, the display
turns gray. When all the four points are set, the display returns to
the normal state.
turns gray. When all the four points are set, the display returns to
the normal state.
Operation/Procedure
When the touch panel is touched, the X and Y coordinate values
of the touched point and the coordinate values of the specified
point are displayed. The coordinate values set with SIM 65-1 are
used as the reference.
of the touched point and the coordinate values of the specified
point are displayed. The coordinate values set with SIM 65-1 are
used as the reference.
Operation/Procedure
Setting of soft switches other than SW1 can be changed and
checked.
checked.
1) Enter the soft switch number to be checked or changed with
10-key.
The current set state is displayed.
2) Enter the number corresponding to the bit to be changed with
10-key.
(Example) When the bit of 5 is to be changed, enter 5.
The set value of 1/0 is alternatively changed every time when
the target key is pressed.
the target key is pressed.
3) After completion of setting of all the bits, press [START] key.
Operation/Procedure
1) Set the destination code with 10-key.
The codes other than the above are recognized as Japan.
2) Press [START] key.
3) The confirmation menu of YES/NO of clear is displayed.
Select one.
4) Press [START] key.
The soft switch (except for the adjustment values) is cleared
according to the destination selected in procedure 1).
according to the destination selected in procedure 1).
NOTE: When the FAX BOX is not installed, initialization including
the adjustment value is performed. (The adjustment value
is stored in the FAX BOX.)
is stored in the FAX BOX.)
65
65-1
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the touch panel (LCD display
section) detection position.
section) detection position.
Section
Operation (Display/Operation key)
Item
65-2
Purpose
Adjustment/Setup/Operation data output/Check
(Display/Print)
(Display/Print)
Function
(Purpose)
(Purpose)
Used to check the result of the touch panel (LCD
display) detection position adjustment. (The
coordinates are displayed.)
display) detection position adjustment. (The
coordinates are displayed.)
Section
Operation (Display/Operation key)
Item
66
66-1
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to change and check the FAX soft switch
functions. (Used to change and check the
functions provided for the FAX soft switches.)
(Only when FAX is installed)
functions. (Used to change and check the
functions provided for the FAX soft switches.)
(Only when FAX is installed)
Section
FAX
Item
SIMULATION 65-1
SIMULATION 65-2
400
500
600
40
100 200 300
100
140
600
180
200
Press [START] key.
Press [CUSTOM SETTINGS] key or [START] key.
66-2
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to clear the FAX soft switch function data
and to set to the default. (Excluding the
adjustment values.) (Only when FAX is installed)
and to set to the default. (Excluding the
adjustment values.) (Only when FAX is installed)
Section
FAX
Item
Data
Japan
0 0 0 0 0 0 0 0
Finland
0 0 1 1 1 1 0 0
U.S.A.
1 0 1 1 0 1 0 1
Norway
1 0 0 0 0 0 1 0
Australia
0 0 0 0 1 0 0 1
Denmark
0 0 1 1 0 0 0 1
U.K.
1 0 1 1 0 1 0 0
Netherlands
0 1 1 1 1 0 1 1
France
0 0 1 1 1 1 0 1
Italy
0 1 0 1 1 0 0 1
Germany
0 0 0 0 0 1 0 0
Switzerland
1 0 1 0 0 1 1 0
Sweden
1 0 1 0 0 1 0 1
Austria
0 0 0 0 1 0 1 0
Newzealand
0 1 1 1 1 1 1 0
Indonesia
0 1 0 1 0 1 0 0
China
0 0 1 0 0 1 1 0
Thailand
1 0 1 0 1 0 0 1
Singapore
1 0 0 1 1 1 0 0
Malaysia
0 1 1 0 1 1 0 0
TW
1 1 1 1 1 1 1 0
India
0 1 0 1 0 0 1 1
Other1
1 1 1 1 1 1 0 1
Philippines
1 0 0 0 1 0 0 1
Other2
1 1 1 1 1 1 0 0
Hongkong
0 1 0 1 0 0 0 0
Ohter3
1 1 1 1 1 0 1 1
1
YES
FAX soft SW is cleared.
2
NO
Not cleared.
SIMULATION 66-1
FAX SOFT SW. SETTING. SELECT 2-120, AND PRESS START.
SIMULATION 66-1
FAX SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS
START.
SOFT SW-2:
1 2 3 4 5 6 7 8
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 74
Operation/Procedure
1) Enter the number corresponding to the memory to be checked
with 10-key.
2) Press [START] key.
In the case of All, all memories are checked only once.
The error address or the data line is displayed individually.
When "repeat" is selected, the operation is repeated until the
result is "NG" or [CUSTOMSETTING" is pressed.
result is "NG" or [CUSTOMSETTING" is pressed.
When Check is "once," the display stops at the result display.
When [CUSTOM SETTINGS] key is pressed, the display returns
to the initial display.
When [CUSTOM SETTINGS] key is pressed, the display returns
to the initial display.
Operation/Procedure
1) Enter the number corresponding to the output mode with 10-
key.
2) Press [START] key.
The output is delivered at the max. send level.
When [CUSTOM SETTINGS] key is pressed during execution,
execution is stopped.
execution is stopped.
When a number is entered and [START] key is pressed during
execution, the kind of signal can be changed.
execution, the kind of signal can be changed.
Press [START] key.
66-3
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operation of the FAX PWB
memory (read/write). (This adjustment is required
when the PWB is replaced with a new one.) (Only
when FAX is installed)
memory (read/write). (This adjustment is required
when the PWB is replaced with a new one.) (Only
when FAX is installed)
Section
FAX
Item
Data
Check connection wire list
NO CHECK
Not checked yet.
CHECKING
Checking
OK
Check complete OK
NG
Check complete NG
Target memory of check
MFP SRAM
MFP SRAM
SRAM
MFP FLASH
FLASH ROM
MFP OP.FLASH
MODEM EEPROM
MODEM EEPROM
MODEM SRAM (G/A)
MODEM SDRAM1
MODEM SDRAM2
MODEM SDRAM2
SIMULATION 66-2
FAX SOFT SW. CLEAR(WITHOUT ADJUSTMENT VALUE).
INPUT COUNTRY CODE, AND PRESS START.
1 2 3 4 5 6 7 8
1
SIMULATION 66-2
FAX SOFT SW. CLEAR.
ARE YOU SURE?
JAPAN
1:YES
2:NO
Press [START] key.
Press [CUSTOM SETTINGS] key.
66-4
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the output operation of data signals
in each data output mode of FAX. (Used to check
the operation of MODEM. ) Send level: Max. (Only
when FAX is installed)
in each data output mode of FAX. (Used to check
the operation of MODEM. ) Send level: Max. (Only
when FAX is installed)
Section
FAX
Item
Operation
1
NOSIGNAL
No signal
17
12.0 V33
12.0 V33
2
33.6 V34
26.4 V34
18
14.4 V17
14.4 V17
3
31.2 V34
31.2 V34
19
12.0 V17
12.0 V17
4
28.8 V34
28.8 V34
20
9.6 V17
9.6 V17
5
26.4 V34
26.4 V34
21
7.2 V17
7.2 V17
6
24.0 V34
24.0 V34
22
9.6 V29
9.6 V29
7
21.6 V34
21.6 V34
23
7.2 V29
7.2 V29
8
19.2 V34
19.2 V34
24
4.8 V27t
4.8 V27t
9
16.8 V34
16.8 V34
25
2.4 V27t
2.4 V27t
10
14.4 V34
14.4 V34
26
0.3 FLG
0.3 FLG
11
12.0 V34
12.0 V34
27
CED 2100
CED 2100
12
9.6 V34
9.6 V34
28
CNG 1100
CNG 1100
13
7.2 V34
7.2 V34
29
0.3 V21
0.3 V21
14
4.8 V34
4.8 V34
30
ANSam
ANSam
15
2.4 V34
2.4 V34
31
RINGER
RINGER
16
14.4 V33
14.4 V33
32
No RBT
No RBT
SIMULATION 66-3
FAX PWB MEMORY CHECK INPUT 1-13, AND PRESS START.
1. All Memory Device Check (once)
2. MFP SRAM(once) 3. MFP SRAM(repeat)
4. MFP FLASH+ OP.FLASH(once)
5. MFP FLASH+ OP.FLASH(repeat)
6. MODEM EEPROM(once) 7. MODEM EEPROM(repeat)
8. MODEM SRAM(G/A)(once) 9. MODEM SRAM(G/A)(repeat)
10. MODEM SDRAM1(once) 11. MODEM SDRAM1(repeat)
12. MODEM SDRAM2(once) 13. MODEM SDRAM2(repeat)
When "repeat" is selected and
[CUSTOM SETTINGS] key is pressed.
[CUSTOM SETTINGS] key is pressed.
SIMULATION 66-3
FAX PWB MEMORY CHECK
MFP SRAM: CHECKING
MFP FLASH: NO CHECK
MFP OP.FLASH: NO CHECK
MODEM EEPROM: NG:A0010000
MODEM SRAM(G/A):NO CHECK
MODEM SDRAM1: NG A11
MODEM SDRAM2: OK
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 75
Operation/Procedure
1) Enter the number corresponding to the output mode with 10-
key.
2) Press [START] key.
The output is delivered at the send level set with the soft switch.
When [CUSTOM SETTINGS] key is pressed during execution,
execution is stopped.
execution is stopped.
When a number is entered and [START] key is pressed during
execution, the kind of signal can be changed.
execution, the kind of signal can be changed.
66-5
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the output operation of data signals
in each data output mode of FAX. (Used to check
the operation of MODEM.) An output is sent at the
send level set by the soft switch. (Only when FAX
is installed)
in each data output mode of FAX. (Used to check
the operation of MODEM.) An output is sent at the
send level set by the soft switch. (Only when FAX
is installed)
Section
FAX
Item
Operation
Press [START] key.
Enter 2 and press [START] key.
SIMULATION 66-4
SIGNAL OUTPUT CHECK.(LEVEL MAX) SELECT 1-32, AND PRESS
START.
1.NOSIGNAL 2.33.6 V34 3.31.2 V34 4.28.8 V34
2.26.4 V34 6.24.0 V34 7.21.6 V34 8.19.2 V34
9.16.8 V34 10.14.4 V34 11.12.0 V34 12.9.6 V34
13.7.2 V34 14.4.8 V34 15.2.4 V34 16.14.4 V33
17.12.0 V33 18.14.4 V17 19.12.0 V17 20.9.6 V17
21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t
25.2.4 V27t 26.0.3 FLG 27.CED 2100 28.CNG 1100
29.0.3 V21 30.ANSam 31.RINGER 32.No RBT
1
SIMULATION 66-4
SIGNAL OUTPUT CHECK.(LEVEL MAX) SELECT 1-32, AND PRESS
START. EXECUTING···.
1.NOSIGNAL 2.33.6 V34 3.31.2 V34 4.28.8 V34
2.26.4 V34 6.24.0 V34 7.21.6 V34 8.19.2 V34
9.16.8 V34 10.14.4 V34 11.12.0 V34 12.9.6 V34
13.7.2 V34 14.4.8 V34 15.2.4 V34 16.14.4 V33
17.12.0 V33 18.14.4 V17 19.12.0 V17 20.9.6 V17
21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t
25.2.4 V27t 26.0.3 FLG 27.CED 2100 28.CNG 1100
29.0.3 V21 30.ANSam 31.RINGER 32.No RBT
1
SIMULATION 66-4
SIGNAL OUTPUT CHECK.(LEVEL MAX) SELECT 1-32, AND PRESS
START. EXECUTING···.
1.NOSIGNAL 2.33.6 V34 3.31.2 V34 4.28.8 V34
2.26.4 V34 6.24.0 V34 7.21.6 V34 8.19.2 V34
9.16.8 V34 10.14.4 V34 11.12.0 V34 12.9.6 V34
13.7.2 V34 14.4.8 V34 15.2.4 V34 16.14.4 V33
17.12.0 V33 18.14.4 V17 19.12.0 V17 20.9.6 V17
21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t
25.2.4 V27t 26.0.3 FLG 27.CED 2100 28.CNG 1100
29.0.3 V21 30.ANSam 31.RINGER 32.No RBT
2
Same
display
display
SIMULATION 66-4
SIGNAL OUTPUT CHECK.(LEVEL MAX) SELECT 1-32, AND PRESS
START.
1.NOSIGNAL 2.33.6 V34 3.31.2 V34 4.28.8 V34
2.26.4 V34 6.24.0 V34 7.21.6 V34 8.19.2 V34
9.16.8 V34 10.14.4 V34 11.12.0 V34 12.9.6 V34
13.7.2 V34 14.4.8 V34 15.2.4 V34 16.14.4 V33
17.12.0 V33 18.14.4 V17 19.12.0 V17 20.9.6 V17
21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t
25.2.4 V27t 26.0.3 FLG 27.CED 2100 28.CNG 1100
29.0.3 V21 30.ANSam 31.RINGER 32.No RBT
2
Press [CUSTOM SETTINGS] key.
Press [CUSTOM SETTINGS] key.
1
NOSIGNAL
No signal
17
12.0 V33
12.0 V33
2
33.6 V34
26.4 V34
18
14.4 V17
14.4 V17
3
31.2 V34
31.2 V34
19
12.0 V17
12.0 V17
4
28.8 V34
28.8 V34
20
9.6 V17
9.6 V17
5
26.4 V34
26.4 V34
21
7.2 V17
7.2 V17
6
24.0 V34
24.0 V34
22
9.6 V29
9.6 V29
7
21.6 V34
21.6 V34
23
7.2 V29
7.2 V29
8
19.2 V34
19.2 V34
24
4.8 V27t
4.8 V27t
9
16.8 V34
16.8 V34
25
2.4 V27t
2.4 V27t
10
14.4 V34
14.4 V34
26
0.3 FLG
0.3 FLG
11
12.0 V34
12.0 V34
27
CED 2100
CED 2100
12
9.6 V34
9.6 V34
28
CNG 1100
CNG 1100
13
7.2 V34
7.2 V34
29
0.3 V21
0.3 V21
14
4.8 V34
4.8 V34
30
ANSam
ANSam
15
2.4 V34
2.4 V34
31
RINGER
RINGER
16
14.4 V33
14.4 V33
32
No RBT
No RBT
Press [START] key.
Enter 2 and press [START] key.
SIMULATION 66-5
SIGNAL OUTPUT CHECK.(SOFT SW.) SELECT 1-32, AND PRESS
START.
1.NOSIGNAL 2.33.6 V34 3.31.2 V34 4.28.8 V34
2.26.4 V34 6.24.0 V34 7.21.6 V34 8.19.2 V34
9.16.8 V34 10.14.4 V34 11.12.0 V34 12.9.6 V34
13.7.2 V34 14.4.8 V34 15.2.4 V34 16.14.4 V33
17.12.0 V33 18.14.4 V17 19.12.0 V17 20.9.6 V17
21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t
25.2.4 V27t 26.0.3 FLG 27.CED 2100 28.CNG 1100
29.0.3 V21 30.ANSam 31.RINGER 32.No RBT
1
SIMULATION 66-5
SIGNAL OUTPUT CHECK.(SOFT SW.) SELECT 1-32, AND PRESS
START. EXECUTING···.
1.NOSIGNAL 2.33.6 V34 3.31.2 V34 4.28.8 V34
2.26.4 V34 6.24.0 V34 7.21.6 V34 8.19.2 V34
9.16.8 V34 10.14.4 V34 11.12.0 V34 12.9.6 V34
13.7.2 V34 14.4.8 V34 15.2.4 V34 16.14.4 V33
17.12.0 V33 18.14.4 V17 19.12.0 V17 20.9.6 V17
21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t
25.2.4 V27t 26.0.3 FLG 27.CED 2100 28.CNG 1100
29.0.3 V21 30.ANSam 31.RINGER 32.No RBT
1
SIMULATION 66-5
SIGNAL OUTPUT CHECK.(SOFT SW.) SELECT 1-32, AND PRESS
START. EXECUTING···.
1.NOSIGNAL 2.33.6 V34 3.31.2 V34 4.28.8 V34
2.26.4 V34 6.24.0 V34 7.21.6 V34 8.19.2 V34
9.16.8 V34 10.14.4 V34 11.12.0 V34 12.9.6 V34
13.7.2 V34 14.4.8 V34 15.2.4 V34 16.14.4 V33
17.12.0 V33 18.14.4 V17 19.12.0 V17 20.9.6 V17
21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t
25.2.4 V27t 26.0.3 FLG 27.CED 2100 28.CNG 1100
29.0.3 V21 30.ANSam 31.RINGER 32.No RBT
2
Same
display
display
SIMULATION 66-5
SIGNAL OUTPUT CHECK.(SOFT SW.) SELECT 1-32, AND PRESS
START.
1.NOSIGNAL 2.33.6 V34 3.31.2 V34 4.28.8 V34
2.26.4 V34 6.24.0 V34 7.21.6 V34 8.19.2 V34
9.16.8 V34 10.14.4 V34 11.12.0 V34 12.9.6 V34
13.7.2 V34 14.4.8 V34 15.2.4 V34 16.14.4 V33
17.12.0 V33 18.14.4 V17 19.12.0 V17 20.9.6 V17
21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t
25.2.4 V27t 26.0.3 FLG 27.CED 2100 28.CNG 1100
29.0.3 V21 30.ANSam 31.RINGER 32.No RBT
2
Press [CUSTOM SETTINGS] key.
Press [CUSTOM SETTINGS] key.
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 76
Operation/Procedure
The paper is automatically selected with the size saved in the
image memory.
image memory.
Operation/Procedure
All image data stored in the image memory are printed.
∗
The confidential receive data are also printed.
The paper is automatically selected with the size saved in the
image memory.
image memory.
Operation/Procedure
1) Enter the number corresponding to the output mode with 10-
key.
2) Press [START] key.
The output is delivered at the max. level.
When the number is entered during execution, the kind of signal
can be changed.
can be changed.
When [START] key is pressed, the voice message is sent. When
[CUSTOM SETTINGS] key is pressed, it is stopped.
[CUSTOM SETTINGS] key is pressed, it is stopped.
66-6
Purpose
User data output/Check (Display/Print)
Function
(Purpose)
(Purpose)
Used to print the confidential pass code. (Used
when the confidential pass code is forgotten.)
(Only when FAX is installed)
when the confidential pass code is forgotten.)
(Only when FAX is installed)
Section
FAX
Item
Data
1
PRINT START
Print start
66-7
Purpose
User data output/Check (Display/Print)
Function
(Purpose)
(Purpose)
Used to print the image memory data (memory
send/receive). (Only when FAX is installed)
send/receive). (Only when FAX is installed)
Section
FAX
Item
Data
1
PRINT START
Print start
(When 1)
SIMULATION 66-6
PASS CODE PRINT OUT. EXECUTING···.
1.PRINT START
SIMULATION 66-6
PASS CODE PRINT OUT.
PRESS START.
1.PRINT START
When there is no print data,
the display returns to the
original state without printing.
the display returns to the
original state without printing.
Press [START] key.
After completion of printing
SIMULATION 66-7
IMAGE MEMORY PRINT OUT. PRESS START.
1.PRINT START
(When 1)
SIMULATION 66-7
IMAGE MEMORY PRINT OUT. EXECUTING···.
1.PRINT START
Press [START] key.
After completion of printing
66-8
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the output operation of various
sound signals of FAX. (Used to check the
operation of the sound output IC.) Send level:
Max. (Only when FAX is installed)
sound signals of FAX. (Used to check the
operation of the sound output IC.) Send level:
Max. (Only when FAX is installed)
Section
FAX
Item
Operation
1 NONE
Mute
11 MESSAGE 9
Message 9
2 PAUSE
Pause sound
12 MESSAGE 10
Message 10
3 MESSAGE1 Message 1
13 MESSAGE 11
Message 11
4 MESSAGE2 Message 2
14 MESSAGE 12
Message 12
5 MESSAGE3 Message 3
15 MESSAGE 13
Message 13
6 MESSAGE4 Message 4
16 MESSAGE 14
Message 14
7 MESSAGE5 Message 5
17 MESSAGE 15
Message 15
8 MESSAGE6 Message 6
18 ALARM
Alarm
9 MESSAGE7 Message 7
19 RINGER
Call ring
10 MESSAGE8 Message 8
20 EXT.TEL.RINGER External TEL ring
SIMULATION 66-8
MESSAGE OUTPUT CHECK.(LEVEL MAX) SELECT 1-20, AND PRESS
START.
1.NONE 2.PAUSE 3.MESSAGE1
4.MESSAGE2 5.MESSAGE3 6.MESSAGE4
7.MESSAGE5 8.MESSAGE6 9.MESSAGE7
10.MESSAGE8 11.MESSAGE9 12.MESSAGE10
13.MESSAGE11 14.MESSAGE12 15.MESSAGE13
16.MESSAGE14 17.MESSAGE15 18.ALARM
19.RINGER 20.EXT.TEL.RINGER
2
Same
display
display
SIMULATION 66-8
MESSAGE OUTPUT CHECK.(LEVEL MAX) SELECT 1-20, AND PRESS
START. EXECUTING···.
1.NONE 2.PAUSE 3.MESSAGE1
4.MESSAGE2 5.MESSAGE3 6.MESSAGE4
7.MESSAGE5 8.MESSAGE6 9.MESSAGE7
10.MESSAGE8 11.MESSAGE9 12.MESSAGE10
13.MESSAGE11 14.MESSAGE12 15.MESSAGE13
16.MESSAGE14 17.MESSAGE15 18.ALARM
19.RINGER 20.EXT.TEL.RINGER
2
SIMULATION 66-8
MESSAGE OUTPUT CHECK.(LEVEL MAX) SELECT 1-20, AND PRESS
START. EXECUTING···.
1.NONE 2.PAUSE 3.MESSAGE1
4.MESSAGE2 5.MESSAGE3 6.MESSAGE4
7.MESSAGE5 8.MESSAGE6 9.MESSAGE7
10.MESSAGE8 11.MESSAGE9 12.MESSAGE10
13.MESSAGE11 14.MESSAGE12 15.MESSAGE13
16.MESSAGE14 17.MESSAGE15 18.ALARM
19.RINGER 20.EXT.TEL.RINGER
1
SIMULATION 66-8
MESSAGE OUTPUT CHECK.(LEVEL MAX) SELECT 1-20, AND PRESS
START.
1.NONE 2.PAUSE 3.MESSAGE1
4.MESSAGE2 5.MESSAGE3 6.MESSAGE4
7.MESSAGE5 8.MESSAGE6 9.MESSAGE7
10.MESSAGE8 11.MESSAGE9 12.MESSAGE10
13.MESSAGE11 14.MESSAGE12 15.MESSAGE13
16.MESSAGE14 17.MESSAGE15 18.ALARM
19.RINGER 20.EXT.TEL.RINGER
2
Press [CUSTOM SETTINGS] key.
Press [CUSTOM SETTINGS] key.
Select 2, and press [START] key.
Select other 1, and press [START] key.
Click on the first or last page to see other AR-M351U / AR-M451U (serv.man17) service manuals if exist.