DOWNLOAD Sharp AR-FX7 Service Manual ↓ Size: 4.14 MB | Pages: 104 in PDF or view online for FREE

AR-FX7  SIMULATION  6 - 6

1.

Enter the country code with the 10-key, and press the [START]
key. 

2.

When "1: (YES)" is selected, the soft SW corresponding to the
country code is cleared. When "2: (NO)" is selected, the simulation
is canceled.

Country code

The codes other than the above are accepted as Japan.

Note: Executable only when the FAX is installed.

Press the [START] key.

Read/write can be checked for FAX PWB memory.

The check result is displayed separately for each memory.

1.

Memory to be checked

2.

Detailed procedure

Interruption cannot be made during operation.

Note: Executable only when the FAX is installed.

Select the signal number with the 10-key, and press the [START] key.
The signal is sent to the line and the machine speaker. (Sending the
signal is continued until the [CUSTOM SETTINGS] key is pressed.)

By entering the signal number and pressing the [START] key during
execution, the signal kind can be changed.

66-2

Adjustment

Used to clear the FAX-related soft SW. (Except for the 
FAX adjustment values)

FAX

Japan

: 00000000

India

: 01010011

U.S.A./Canada : 10110101

Hong Kong

: 01010000

Australia

: 00001001

Spain

: 10100000

U.K.

: 10110100

Portugal

: 10001011

France

: 00111101

Italy

: 01011001

Germany

: 00000100

Switzerland : 10100110

Sweden

: 10100101

Finland

: 00111100

New Zealand

: 01111110

Denmark

: 00110001

China

: 00100110

Norway

: 10000010

Singapore

: 10011100

Netherlands : 01111011

Taiwan

: 11111110

Luxembourg : 01101001

Middle East

: 11111101

Belgium

: 00001111

Malaysia

: 01101100

66-3

Operation test/check

FAX PWB memory check

FAX

Operation

DRAM

SRAM
Flash ROM

Program area

SUM check only

Memory area

Option memory

The memory size follows the 
automatically detected value.

PAGE

1

0 0 0 0 1 0 0 1

1 2 3 4 5 6 7 8

1

"55H" is written to all the addresses of each memory, and the 
address data are read in sequence to check that they were 
properly written.

2

"AAH" is written to all the addresses of each memory, and the 
address data are read in sequence to check that they were 
properly written.

3

"00H" is written to all the addresses of each memory, and the 
address data are read in sequence to check that they were 
properly written.

4

Perform checks 1 - 3 sequentially. If there is no abnormality, it is 
"OK." If there is any abnormality, "NG" is notified to the error 
address.

5

After completion of check, the memory is returned to the initial 
state.
(CPU is not reset)

66-4

Operation test/check

Signal send mode (Signal send level: Max.)

FAX

Operation

Item

Send signal

Send level

Selection 

menu

1

NO SIGNAL Signal not sent

None

2

33.6 V34

–

–

3

31.2 V34

–

–

4

28.8 V34

–

–

5

26.4 V34

–

–

6

24.0 V34

–

–

7

16.0 V34

–

–

8

19.2 V34

–

–

9

16.8 V34

–

–

10 14.4 V34

–

–

11 12.0 V34

–

–

12 9.6 V34

–

–

13 7.2 V34

–

–

14 4.8 V34

–

–

15 2.4 V34

–

–

16 14.4 V33

–

–

17 12.0 V33

–

–

18 14.4 V17

–

–

19 12.0 V17

–

–

20 9.6 V17

–

–

21 7.2 V17

–

–

22 9.6 V29

–

–

23 7.2 V29

–

–

24 4.8 V27t

–

–

1

AR-FX7  SIMULATION  6 - 7

Note: Executable only when the FAX is installed.

Select the signal number with the 10-key, and press the [START] key. 

By setting the signal number, signals are sent to the line and the
machine speaker. (Sending signals is continued until interruption com-
mand is made (by pressing [CUSTOM SETTINGS] key.)

By entering the signal number and pressing the [START] key during
execution, the signal kind can be changed.

Note: Executable only when the FAX is installed.

Press the [START] key.

The confidential ID table (confidential BOX numbers, confidential BOX
names, and confidential password) is printed. 

The confidential data of My company mode is printed separately.

Note: Executable only when the FAX is installed.

25 2.4 V27t

–

–

26 0.3 FLG

7EH Flag signal

Yes

27 CED2100

Tone signal

Yes

28 CNG1100

29 0.3 V21
30 ANSam

31 RINGER

Pseudo-ringer sound
([ON HOOK] key ON)

None

32 No MSG

Voice message (no sound)

None

Under the state where the ring back 
tone can be sent to the line, keep the 
sound composition IC volume to 0.

33 No RBT

Ring back tone (no sound)

None

Under the state where the ring back 
tone can be sent to the line, keep the 
G/A volume to 0.

34 DP MAKE

Dial pulse (make)

1: 0dB
2: Soft SW

Maintain the make state with keeping 
the condition to be able to send to the 
dial pulse line.

35 DP BRK

Dial pulse (break)

1: 0dB
2: Soft SW

Maintain the break state with keeping 
the condition to be able to send to the 
dial pulse line.

66-5

Operation test/check

Signal send mode (Signal send level soft SW setting)

FAX

Operation

Signal number

Send signal

Send level

Selection 

menu

1 NO SIGNAL Signal not sent

None

2 33.6 V34

33.6 V34

–

3 31.2 V34

31.2 V34

–

4 28.8 V34

28.8 V34

–

5 26.4 V34

26.4 V34

–

6 24.0 V34

24.0 V34

–

7 16.0 V34

16.0 V34

–

8 19.2 V34

19.2 V34

–

9 16.8 V34

16.8 V34

–

10 14.4 V34

14.4 V34

–

11 12.0 V34

12.0 V34

–

Item

Send signal

Send level

Selection 

menu

1

12 9.6 V34

9.6 V34

–

13 7.2 V34

7.2 V34

–

14 4.8 V34

4.8 V34

–

15 2.4 V34

2.4 V34

–

16 14.4 V33

14.4 V33

–

17 12.0 V33

12.0 V33

–

18 14.4 V17

14.4 V17

–

19 12.0 V17

12.0 V17

–

20 9.6 V17

9.6 V17

–

21 7.2 V17

7.2 V17

–

22 9.6 V29

9.6 V29

–

23 7.2 V29

7.2 V29

–

24 4.8 V27t

4.8 V27t

–

25 2.4 V27t

2.4 V27t

–

26 0.3 FLG

7EH Flag signal

Yes

27 CED2100

Tone signal

Yes

28 CNG1100

29 0.3 V21
30 ANSam

31 RINGER

Pseudo-ringer sound
([ON HOOK] key ON)

None

32 No MSG

Voice message (no sound)

None

Under the state where the ring back 
tone can be sent to the line, keep the 
sound composition IC volume to 0.

33 No RBT

Ring back tone (no sound)

None

Under the state where the ring back 
tone can be sent to the line, keep the 
G/A volume to 0.

34 DP MAKE

Dial pulse (make)

1: 0dB
2: Soft SW

Maintain the make state with keeping 
the condition to be able to send to the 
dial pulse line.

35 DP BRK

Dial pulse (break)

1: 0dB
2: Soft SW

Maintain the break state with keeping 
the condition to be able to send to the 
dial pulse line.

66-6

Data output, check

Printing the confidential password

FAX

Data Confidential/Pass 

code

Signal number

Send signal

Send level

Selection 

menu

1

AR-FX7  SIMULATION  6 - 8

Press the [START] key.

Used to input all image data (including confidential reception data,
remote send image, not-sent image) stored in image memory of the
FAX section.

The output image is remained even after outputting.

Note: Executable only when the FAX is installed.

Select the message number with the 10-key, and press the [START]
key.

By setting the message No., the sound message is sent to the line and
the speaker of the body. (The message is repeated until the interrup-
tion command is provided by pressing the [CUSTOM SETTINGS] key.)

By pressing the [START] key during execution, the signal kind can be
changed.

Message No. 5 can be heard by an external telephone speaker.

Note: Executable only when the FAX is installed.

Select the message number with the 10-key, and press the [START]
key.

By setting the message No., the sound message is sent to the line and
the speaker of the body. (The message is repeated until the interrup-
tion command is provided by pressing the [CUSTOM SETTINGS] key.)

By pressing the [START] key during execution, the signal kind can be
changed.

Message No. 5 can be heard by an external telephone speaker.

Note: Executable only when the FAX is installed.

Select "1: YES" with the 10-key and press the [START] key. (When "2:
NO" is selected, the simulation is canceled.)

Used to clear all image data (including confidential reception data)
stored in image memory of the FAX section.

The management table is also cleared (initialized) at the same time.

* lIf there is any print data, the power must be turned off after clearing.

Note: Executable only when the FAX is installed.

66-7

Data output, check

Print the screen memory contents

FAX

Data Image 

data

66-8

Operation test/check

Voice Message send (Signal send level: 
Max.) (Japan only)

FAX

Operation

Item

Voice message

1

NONE

Silent

2

FAX/TEL MSG1 

"Hold the line a minute, please send fax."
(TEL/FAX voice response)

3

FAX/TEL MSG2

"Hold the line a minute."
(TEL/FAX voice response)

4

FAX/TEL MSG3

"Not around here, please send fax."
(TEL/FAX voice response)

5

CHANGED RX MSG

"Ding Dong"
(Sound delivered when switching to remote 
reception)

6

RINGER

Call sound

7

EXT.TEL RINGER

External telephone call

1

2

66-9

Operation test/check

Used to send the voice message. (Signal send level: 
Set by soft SW.) (Japan only)

FAX

Operation

Item

Voice message

1

NONE

Silent

2

FAX/TEL MSG1 

"Hold the line a minute, please send fax."
(TEL/FAX voice response)

3

FAX/TEL MSG2

"Hold the line a minute."
(TEL/FAX voice response)

4

FAX/TEL MSG3

"Not around here, please send fax."
(TEL/FAX voice response)

5

CHANGED RX MSG

"Ding Dong"
(Sound delivered when switching to remote 
reception)

6

RINGER

Call sound

7

EXT.TEL RINGER

External telephone call

66-10

Adjustment/Setting/Check

Image data memory clear

FAX

Data

Image data

2

1

AR-FX7  SIMULATION  6 - 9

Select the signal number with the 10-key, and press the [START] key.

By setting the signal number, the specified signal is delivered to the
line at the speed of 300bps. (The signal is continuously sent until the
interruption command is provided by pressing the [CUSTOM SET-
TINGS] key.)

The signal send level can be selected from 0dB or the soft SW set
value.

The signal send level is returned to the soft SW set value before exe-
cution of the mode after completion of the mode.

By entering the number and pressing the [START] key during execu-
tion, the signal kind can be changed.

Note: Executable only when the FAX is installed.

Select the signal number with the 10-key, and press the [START] key.

By setting the signal number, the specified signal is delivered to the
line at the speed of 300bps. (The signal is continuously sent until the
interruption command is provided by pressing the [CUSTOM SET-
TINGS] key.)

The signal send level can be selected from 0dB or the soft SW set
value.

The signal send level is returned to the soft SW set value before exe-
cution of the mode after completion of the mode.

By entering the number and pressing the [START] key during execu-
tion, the signal kind can be changed.

Note: Executable only when the FAX is installed.

Enter the number with the 10-key, [*] key, and [#] key.

Press the [CLEAR] key to return to the initial state.

Press the [START] key to register the entered number.

Note: Executable only when the FAX is installed.

1.

Select the item with the 10-key, and press the [START] key.

2.

Set the make time with the 10-key.

The dial is sent with the set value + 26ms. 

The sending dial cannot be interrupted.

Note: Executable only when the FAX is installed.

1.

Select the item with the 10-key, and press the [START] key.

2.

Set the make time with the 10-key.

The dial is sent with the set value + 26ms. 

The sending dial cannot be interrupted.

Note: Executable only when the FAX is installed.

66-11

Operation test/check

Used to send 300bps signals. (Signal send level: 
Max.)

FAX

Operation

Item

1

NO SIGNAL

2

11111

3

11110

4

00000

5

010101

6

00001

66-12

Operation test/check

Used to send 300bps signals. (Signal send level: Set 
by soft SW)

FAX

Operation

Item

1

NO SIGNAL

2

11111

3

11110

4

00000

5

010101

6

00001

1

66-13

Setting

Used to register the dial numbers.

FAX

Operation

66-14

Operation check/test

Used to perform the dial test. (10 PPS send test)

FAX

Operation

Item

Content

Setting range

0

EXECUTE

Execution

–

1

MAKE TIME

Dial pulse make time setting

0-15

66-15

Operation check/test

Used to perform the dial test. (20 PPS send test)

FAX

Operation

Item

Content

Setting range

0

EXECUTE

Execution

–

1

MAKE TIME

Dial pulse make time setting

0-15

1

1