Sharp AR-F151 (serv.man16) User Manual / Operation Manual ▷ View online
CHOOSING SUITABLE MEDIA
3-1
52 /m
2
85 /m
2
148 mm
210 mm
257 mm
500 mm
Originals Suitable for Faxing
Size and Weight
The size and weight of documents that you can load in the SPF depend on whether
you load one sheet at a time or several sheets at once.
you load one sheet at a time or several sheets at once.
When using the SPF
One sheet at a time:
Several sheets at once:
Note: When feeding in a long document, grasp the document at the edges to guide it
into the unit.
When using the original table
Note: When you are using the faxing functions of the unit, your documents (originals)
are, in effect, being scanned through the unit. The area of a document that is
scanned by the unit while faxing is slightly smaller than the actual document
(original) size. Any text or graphics outside this area will not be scanned.
scanned by the unit while faxing is slightly smaller than the actual document
(original) size. Any text or graphics outside this area will not be scanned.
52 /m
2
85 /m
2
148 mm
210 mm
257 mm
364 mm
3. CHOOSING SUITABLE MEDIA
Make sure that the documents you want to fax meet specifications and guidelines listed
in this section.
in this section.
Maximum
257 mm
364 mm
1mm ~ 4 mm
Max. 4.5 mm (along the
other edges in totals)
other edges in totals)
4 mm or less
Scanning length
and width
and width
03_CHOOSING.p65
3/22/00, 2:39 PM
1
CHOOSING SUITABLE MEDIA
3-2
Unsuitable Originals
General guidelines:
• All clips, staples, and pins should be removed from originals before they are used. If
these are not removed, they may damage the unit.
• Ink, glue, and correction fluid on originals must be completely dry before using the
documents with the unit.
• Originals that are in some way dangerous to the internal mechanisms of the unit
should not be used.
• When faxing, any writing on the originals that is yellow, yellowish-green, or light blue
cannot be transmitted.
The following kinds of originals should not be used:
• Originals with a glossy coating
• Originals with static electricity
• Originals with tears, folds, or curls
• Originals that have become stuck together and cannot be easily separated
• Originals with holes, windows, or perforations
• Transparency films, tracing paper, or other transparencies
• Originals with plastic or metallic coatings
Notes:
• SHARP does not accept any responsibility for the loss or damage of originals.
• It is a good idea to copy valuable originals on a flat-bed copier before using them with
• SHARP does not accept any responsibility for the loss or damage of originals.
• It is a good idea to copy valuable originals on a flat-bed copier before using them with
the unit.
Originals Suitable for Faxing
03_CHOOSING.p65
3/22/00, 2:39 PM
2
HOW TO USE THE FAX FUNCTION
4-1
The stand alone fax component of your unit offers a range of sophisticated features
that allow you to control image quality, reception mode, broadcasting, polling, and
transmission priorities. Functions such as sending documents from memory and
substituting reception into memory are possible, due to the large memory capacity.
that allow you to control image quality, reception mode, broadcasting, polling, and
transmission priorities. Functions such as sending documents from memory and
substituting reception into memory are possible, due to the large memory capacity.
Sending Documents
Setting the Document
Original face up
4. HOW TO USE THE FAX FUNCTION
This section describes setting documents in the SPF or on the original table.
When Using the SPF:
1
Confirm that there are no
documents on the original table
and that copying is not in progress,
then gently close the original cover.
documents on the original table
and that copying is not in progress,
then gently close the original cover.
2
Adjust the document guides to the
width of your document.
width of your document.
3
Place the document face up and
push it gently into the document
feeder tray. The top edge of the
document should enter the fax first.
push it gently into the document
feeder tray. The top edge of the
document should enter the fax first.
4
There are two ways to send the fax:
• To scan the document into memory,
then dial and transmit, continue with
the “Dialling and Transmitting”
section.
the “Dialling and Transmitting”
section.
• To dial and transmit the document
directly without first scanning it into
memory, press the DOCUMENT key.
“DIRECT SEND” will appear in the
display. Continue with the “Dialling
and Transmitting” section.
memory, press the DOCUMENT key.
“DIRECT SEND” will appear in the
display. Continue with the “Dialling
and Transmitting” section.
04_THE FAX.p65
3/22/00, 2:39 PM
1
HOW TO USE THE FAX FUNCTION
4-2
When placing the Original on the Table:
1
Confirm that there are no
documents in the SPF, and open
the original cover.
documents in the SPF, and open
the original cover.
2
Place the document face down on
the original table. Align the
document according to the original
scale in the illustration below. (Line
up the centre of the edge of the
document with the ( ) mark.)
the original table. Align the
document according to the original
scale in the illustration below. (Line
up the centre of the edge of the
document with the ( ) mark.)
3
Gently close the original cover.
Note: When using the original table, do not set documents in the SPF.
4
Press the BOOK SEND key.
5
Select the document size A4 or B4
from those displayed.
from those displayed.
• You can now make resolution or
contrast settings as described in the
next section and dial and transmit the
fax. (See “Dialling and Transmitting”
in this chapter)
next section and dial and transmit the
fax. (See “Dialling and Transmitting”
in this chapter)
6
Press the BOOK SEND key to scan
the page into memory. If you have
more than one document to read
into memory, place the next page,
and press the BOOK SEND key to
read each page.
the page into memory. If you have
more than one document to read
into memory, place the next page,
and press the BOOK SEND key to
read each page.
mark
Original scale
Sending Documents
DOCUMENT SIZE?
1:A4 2:B4
1:A4 2:B4
04_THE FAX.p65
3/22/00, 2:39 PM
2
Click on the first or last page to see other AR-F151 (serv.man16) service manuals if exist.