DOWNLOAD Sharp AR-C200P (serv.man6) Service Manual ↓ Size: 5.71 MB | Pages: 127 in PDF or view online for FREE

MAINTENANCE > 149

Seal the aperture on each image drum and its toner cartridge 
with plastic adhesive tape (1) to prevent any toner spillage 
during transportation.

Replace the four image drums complete with their toner 
cartridges back into the printer.

Using the original packaging material, place the printer inside 
its box and seal the box.

TROUBLESHOOTING > 103

The liquid crystal display (LCD) on the control panel indicates the 
printer status and if there is a problem with the printer. Status and 
error messages are listed below together with an explanation of what 
each message means:

***** TONER LOW

Toner is low (***** indicates colour).

***** TONER SENSOR 
ERROR

Error with the toner sensor (***** indicates colour). Call 
for service.

BELT UNIT MISSING

Transfer belt unit is missing.

CANCELLING JOB

Cancelling the current job.

CENTRO I/F ERROR

Centronics interface error (parallel interface).

CHANGE ***** IMAGE DRUM

Change the image drum (***** indicates colour).

CHANGE BELT UNIT

Change the transfer belt.

CHANGE FUSER UNIT

Change the fuser unit.

CHANGE PAPER TO *****

Paper must be changed to correct paper size and/or 
media type (***** indicates size or media type).

CHECK BELT UNIT

Check the transfer belt for paper jam, correct 
installation, etc.

CHECK DUPLEX

Check the duplex unit for paper jam, correct installation, 
etc.

CHECK FUSER UNIT

Check the fuser unit for paper jam, correct installation, 
etc.

CHECK IMAGE DRUM

Check the image drum for correct installation, etc. 
Colour will be indicated.

COLLATE FAIL

Collating of multiple copies has failed.

COLOUR ADJUSTING

Adjusting head so that colours do not shift on to each 
other.

COLOUR BALANCE ADJUST

Adjust the colour balance.

COMMUNICATION ERROR

There is an error with communications to computer.

DATA ARRIVE

Data has been received but processing has not started 
yet.

DATA PRESENT

Un-printed data remains in buffer. Waiting for data to 
follow.

TROUBLESHOOTING > 104

DISK FILE OPERATION 
FAILED

Error with hard disk operations.

DISK FILESYSTEM IS FULL

Hard disk/flash memory full.

DISK FULL

The internal hard drive is full.

EEPROM INITIALIZE ERROR

Call for service.

EMPTY

Indicates which paper tray is empty.

ERROR POSTSCRIPT

A PostScript error has occurred.

FATAL ERROR

Call for service.

FUSER UNIT MISSING

Fuser unit is missing.

INSTALL ADDITIONAL 
MEMORY

Additional memory is required before job can be 
printed.

INSTALL NEW IMAGE DRUM

Install a new image drum. Colour will be indicated.

INSTALL NEW TONER

Install a new toner cartridge. Colour will be indicated.

INSTALL PAPER CASSETTE

Install the paper cassette. Paper tray will be indicated.

INVALID DATA

Data is incorrect.

LOAD

Load correct paper size/type. Size/type will be 
indicated. 

MEDIA MISMATCH

Paper type set via menu does not match that sent via 
driver.

NEAR END

The paper in the selected ***** is nearly finished (***** 
indicates paper tray).

NETWORK ERROR

Network error.

OFFLINE

Shows off-line status.

ONLINE

Shows on-line status.

OPEN UPPER COVER

Open the upper cover.

PLEASE POWER OFF

Printer must be switched off after disk/flash 
initialisation.

POWER SAVE

The printer is in powersave mode.

PRINTING

Data is being printed.

PROCESSING

Data is being processed.

RAM CHECK

RAM is being checked after switching printer on.

REGISTRATION ADJUST TEST

Registration adjustment being tested.

REGISTRATION ERROR

An error has occurred setting up the registration.

REMOVE THE PAPER

Indicates wrong paper being used.

RS232C FRAMING ERROR

Serial framing error. Check configuration of serial card.

TROUBLESHOOTING > 105

RS232C OVERFLOW ERROR

Serial overflow error. Check configuration of serial card.

RS232C OVERRUN ERROR

Serial overrun error. Check configuration of serial card.

RS232C PARITY ERROR

Serial parity error. Check configuration of serial card.

SERVICE CALL

A serious error has occurred. Call for service.

SHUTDOWN

Starts the shutdown procedure to protect file system on 
hard disk.

SIZE MISMATCH

Change paper to correct size/type.

STACKER FULL

Stacker is full. Remove paper.

UNSUITABLE SIZE

Indicates wrong paper size.

USB I/F ERROR

USB interface error.

WARMING UP

The printer is warming up.