DOWNLOAD Sharp AR-C170 (serv.man26) Service Manual ↓ Size: 3.39 MB | Pages: 72 in PDF or view online for FREE

AR-C170M  SIMULATION  9 - 13

Scanning is performed at the magnification ratio set in procedure 1 
is executed.

During scanning, the [EXECUTE] key is highlighted. If the 
[EXECUTE] key is pressed under this state, the operation is 
interrupted.

After completion of scanning, the [EXECUTE] key returns to the 
normal display.

To resume scanning, start with procedure 2. To change the 
magnification ratio, start with procedure 1.

Scanning is performed at the max. scanning length (432 mm). If, 
however, the magnification ratio is set to a value greater than 
100% in procedure 1, the scanning length is changed accordingly.

The active sensors and detectors are highlighted.

• The light source unit is at the home position. a MHPS is 

highlighted.

• The light source unit is not at the home position. a MHPS is 

displayed normally.

Scanning is repeatedly performed until the [EXECUTE] key or the 
interruption key is pressed.

1

-1

Operation test/check

Used to check the operations of the scanner unit and 
its control circuit.

Scanner (reading)

Operation

1. Select the copy (scanning) magnification ratio 

with the zoom key. The magnification ratio can 
be increased or decreased with the [ZOOM] key 
by the increment of 1%. The selected 
magnification ratio is displayed on the 
magnification ratio display.

2. Press the [EXECUTE] key.

1

-2

Operation test/check

Used to check the sensors and detectors in the 
scanner section and the related circuits.

Scanner (reading)

Operation

The operations of sensors and detectors in the 
scanner section are displayed.

1

-5

Operation test/check

Used to check the scanner (scanning) unit and its 
control circuit.

Scanner (reading)

Operation

1. Select the copy (scanning) magnification ratio 

with the key (touch panel).  The magnification 
ratio can be increased or decreased with the 
[ZOOM] key by the increment of 1%.
The selected magnification ratio is displayed on 
the magnification ratio display.

2. Select the scan mode (Color / B/W). 
3. Press the [EXECUTE] key.

Scanning is repeated under the conditions set in 
procedures 1 and 2.
During scanning, the [EXECUTE] key is 
highlighted. 

2

-2

Operation test/check

Used to check the operations of the sensors and 
detectors in the document feeder unit and their 
related circuits. 

Automatic document feeder

Operation

The operating status of the sensors and detectors in 
the document feeder unit is displayed.  
The active sensors and detectors are highlighted.

W0

Document set sensor

PAPER

Document transport sensor

COVER 
OPEN

Unit (OC cover) open/close sensor

PO

Paper exit sensor

COVER

Paper feed cover open/close sensor

L1

Document length sensor 1

L2

Document length sensor 2

W1

Document width sensor (small)

W2

Document width sensor (middle)

W3

Document width sensor (large)

AR-C170M  SIMULATION  9 - 14

During the load operation, the [EXECUTE] key and the load key 
are highlighted. Under this state, pressing the [EXECUTE] key 
interrupts the load operation.

(Loads to be selected)

(When the sorter is installed)

2

-3

Operation test/check

Used to check the operations of the motors, 
solenoids, and the PS clutch in the document feeder 
unit. 

Automatic document feeder

Operation

1. The names of the loads that can be operated are 

displayed. Select the load to be checked with the 
key, and the selected load is highlighted.

2. Press the [EXECUTE] key.

MOT

Motor

PSOL

Paper feed solenoid

RSOL

Paper reverse solenoid

GSOL

Paper exit fate solenoid

CLH

PS clutch

3

-2

Operation test/check

Used to check the operations of the sensors and 
detectors in the finisher and the related circuits.

Finisher

Operation

The operating status of the sensors and detectors of 
the finisher is displayed. The active sensor/detector 
display is highlighted.

FES

Inlet sensor

FPHPS

Paddle HP sensor

FARHPS

Bundle roller HP sensor

FFJHPS

Alignment HP sensor (F)

FRJHPS

Alignment HP sensor (R)

FAS

Alignment tray sensor

FOBHPS

Paper exit belt HP sensor

FBES

Tray paper sensor

FSLS

Paper surface sensor

FFPS

Binding position sensor

FFHPS

Binding HP sensor

FFRHPS

Binding roller HP sensor

FFES

Binding paper sensor

FFE

Binding clock sensor

FULS

Lift upper limit sensor

FLLS

Lift lower limit sensor

FLE

Lift clock sensor

FSHPS

Slide HP sensor

FSTHPS

Stapler HP sensor

FSS

Staple sensor

FSUC

Stapler connection sensor

FMLS

Lift middle sensor

FSPS

Self prime sensor

FFDS

Front door sensor

FCS

Upper cover sensor

FFDSW

Front door switch

FJS

Joint switch

FSSS

Stapler safety switch

FPTS

Punch timing sensor

FPSS1

Punch side resist sensor 1

FPSS2

Punch side resist sensor 2

FPSS3

Punch side resist sensor 3

FPSS4

Punch side resist sensor 4

FPDS

Punch dust sensor

FPUC

Punch connection

FPSHPS

Punch side resist home position

FPE

Punch motor encoder

SBPED

Sensor in bin

SLDHP

Lead cam HP sensor

SGBHP

Guide bar HP sensor

SBUHP

Bin unit HP sensor

SPPD

Paper exit sensor

SJSW

Joint switch

SPSW2

Push switch 2

SPSW3

Push switch 3

SDIPSW1

DIP switch (SW1)

SDIPSW2

DIP switch (SW2)

SDIPSW3

DIP switch (SW3)

SDIPSW4

DIP switch (SW4)

SDIPSW5

DIP switch (SW5)

SDIPSW6

DIP switch (SW6)

3

-3

Operation test/check

Used to check the loads in the finisher and the 
control circuit.

Finisher

Operation

1. The names of the loads that can be checked are 

displayed. Select a load to be checked with the 
key.

2. Press the [EXECUTE] key. The selected load 

operates.

FFM

Transport motor

FFSM

Stapler motor

FPM

Paddle motor

FLM

Shift motor

FAM

Bundle exit motor

FPNM

Punch motor

FFJM

Alignment motor (F) FPSM

Puncher side resist motor

FRJM

Alignment motor (R) FFC

Folding clutch

FSM

Slide motor

SBSM

Bin unit shift motor

SPFM

Transport motor

SGBM

Guide bar drive motor

AR-C170M  SIMULATION  9 - 15

(Sensors to be detected)

During the operation of the load, the [EXECUTE] key is 
highlighted. If the [EXECUTE] key is pressed while it is 
highlighted, the operation is stopped.

(Loads to be selected)

3

-10

Operation test/check

Used to adjust the sections in the finisher.

Finisher

Operation

1. Select the adjustment item with the scroll key. 
2. Enter the adjustment value with the 1o-key and 

press the OK key to set the value.

Item

Set 

range

Initial 
value

A

Saddle binding position adjustment

0 – 400

200

B

Saddle folding position adjustment

0 – 400

200

C

Front alignment position adjustment 

0 – 20

10

D

Rear alignment position adjustment

0 – 20

10

E

Staple rear one-point binding position 
adjustment

0 – 200

100

F

Staple front one-point binding position 
adjustment

0 – 200

100

G Staple two-point binding center 

adjustment

0 – 200

100

H

Staple two-point binding pitch adjustment

0 – 100

50

I

Punch center adjustment

47 – 53

50

J

Punch hole position adjustment

0 – 100

50

4

-2

Operation test/check

Used to check the operations of the desk/large 
capacity tray sensors and detectors and the related 
circuits.

Paper feed

Operation

The operating conditions of the sensors and 
detectors in the paper feed section are displayed. 
The active sensors and detectors are highlighted.

DLUD1

Desk 1cs upper limit detection

DLUD2

Desk 2cs upper limit detection

DLUD3

Desk 3cs upper limit detection

DPED1

Desk 1cs paper empty detector

DPED2

Desk 2cs paper empty detection

DPED3

Desk 3cs paper empty detection

DCSPS1

Desk 1cs remaining quantity detection

DCSPS2

Desk 2cs remaining quantity detection

DCSPS3

Desk 3cs remaining quantity detection

DPPD1

Desk paper transport detection 1

DPPD2

Desk paper transport detection 2

DPPD3

Desk paper transport detection 3

DLUID1

Desk 1cs lift unit installation detection

DLUID2

Desk 2cs lift unit installation detection

DLUID3

Desk 3cs lift unit installation detection

DDOPD

Desk door open detection

DCSS11

Desk 1cs paper size detection 1

DCSS12

Desk 1cs paper size detection 2

DCSS13

Desk 1cs paper size detection 3

DCSS14

Desk 1cs paper size detection 4

DCSS21

Desk 2cs paper size detection 1

DCSS22

Desk 2cs paper size detection 2

DCSS23

Desk 2cs paper size detection 3

DCSS24

Desk 2cs paper size detection 4

DCSS31

Desk 3cs paper size detection 1

DCSS32

Desk 3cs paper size detection 2

DCSS33

Desk 3cs paper size detection 3

DCSS34

Desk 3cs paper size detection 4

LTD

Transport sensor

LUD

LCC upper limit detection

LLD

LCC lower limit detection

LPED

LCC paper empty detection

LTOD

LCC main unit connection detection 

LCD

LCC tray insertion detection 

LOSW

LCC upper open/close detection SW

LRE

LCC lift motor encoder

24V

LCC24V detection 

LLSW

LCC upper limit SW

4

-3

Operation test/check

Used to check the operations of the desk/large 
capacity tray loads and the control circuit.

/

Paper feed

Operation

1. The names of the loads that can be checked are 

displayed. Select a load to be checked with the 
key, and the selected load is highlighted.

2. Press the [EXECUTE] key. The load selected in 

procedure 1 starts the operation.

DM

Desk transport motor

DLM1

Desk 1cs lift-up motor

DLM2

Desk 2cs lift-up motor

DLM3

Desk 3cs lift-up motor

DPFC1

Desk 1cs paper feed clutch

DPFC2

Desk 2cs paper feed clutch

DPFC3

Desk 3cs paper feed clutch

DTRC

Desk transport clutch

DPFS1

Desk 1cs paper feed solenoid

DPFS2

Desk 2cs paper feed solenoid

DPFS3

Desk 3cs paper feed solenoid

LTM

LCC transport motor

LLM

LCC lift motor operation

LPFCL

LCC paper feed clutch

LPSL

LCC paper feed solenoid

LTCL

LCC transport clutch

LTLSL

LCC tray lock solenoid

AR-C170M  SIMULATION  9 - 16

When the [TRC ON] key or the [TRC OFF] key is pressed, the 
TRC clutch is turned ON or OFF.

If the response of monitoring TRC ON/OFF is made, DESK 
SENSOR TRC ON/OFF is displayed.

↓

6sec

The selected heater lamp repeats ON/OFF in the frequency of 
500msec for 10sec. (The [EXECUTE] key is highlighted.) Then the 
[EXECUTE] key returns to the normal display. When the 
[EXECUTE] key is pressed during ON/OFF operation of the heater 
lamp, the heater lamp is turned OFF and the  [EXECUTE] key 
returns to the normal display.

After 10 sec, the scanner lamp is turned OFF. At that time, the 
[EXECUTE] key returns to the normal display.

4

-5

Operation test/check

Used to check the operations of the clutch TRC and 
the monitor.

/

Paper feed

Operation

1. Press the [TRC ON] key. (The load operates.)
2. Press the [TRC OFF] key to terminate checking.

5

-1

Operation test/check

Used to check the operations of the display lamp 
(LED)/LCD on the operation panel and the control 
circuits. 

Operation (Display, procedure)

Operation

The LCD shows the following message. (The 
contrast changes in the sequence of Current level 

→

 

MAX 

→

 MIN 

→

 Current level 

→

 MAX 

→

 MIN in every 

2sec.) During that period, each LED is lighted for 
12sec.

5

-2

Operation test/check

Used to check the operations of the heater lamp and 
its control circuit.

/

Fusing

Operation

1. Select the lamp to be checked with the key.
2. Press the [EXECUTE] key.

HL1 (UPPER)

Upper heater lamp

HL2 (LOWER)

Lower heater lamp

HL1&2 (UPPER & LOWER)

Upper/lower fusing heater lamp

5

-3

Operation test/check

Used to check the operations of the scanner lamp 
and its control circuit.

/

Scanner (reading)

Operation

When the [EXECUTE] key is pressed, the scanner 
lamp is lighted for 10 sec. While the scanner lamp is 
lighted, the [EXECUTE] key is highlighted. If the 
[EXECUTE] key is pressed under this state, the 
lamp is turned OFF.