Sharp AR-AX1 (serv.man2) User Manual / Operation Manual ▷ View online
AXIS 700
User’s Manual
Section 2: Basic Installation
13
Physical Description
Back Panel
Network Connectors
The AXIS 700 is equipped with 10baseT and 10base2 connectors for
connection to the Ethernet network.
connection to the Ethernet network.
Power Supply
The AXIS 700 can use either the AXIS PS-C or AXIS PS-E power
supply.
supply.
Push Button
The Push button is used for restoring the factory default settings. See
“Restoring Factory Default Settings” on page 55.
“Restoring Factory Default Settings” on page 55.
SCSI Connector
The AXIS 700 is equipped with a SCSI connector for connection to a
scanner.
scanner.
Front Panel
The front panel indicators show the status of the AXIS 700. The
indicators have the following functions:
indicators have the following functions:
Status
The Status indicator flashes during startup and turns off when the
AXIS 700 is ready for use. If it remains on, check the LCD for error
messages.
AXIS 700 is ready for use. If it remains on, check the LCD for error
messages.
SCSI connector
Network connectors
Power supply
10baseT 10base2
Push button
Section 2: Basic Installation
AXIS 700 User’s Manual
14
Busy
The Busy indicator turns on when the AXIS 700 is allocated for use
and remains on during the scanning process.
and remains on during the scanning process.
Network
The Network indicator indicates network activity.
Power
The Power indicator indicates that power is connected to the AXIS
700.
700.
Note:
While the AXIS 700 is idle, the Power indicator should be on, the
Network indicator should flash randomly, and the Status and
Busy indicators should be off.
Busy indicators should be off.
Control Panel
The AXIS 700 message display consists of 2 lines by 16 characters
indicating status and menu options.
indicating status and menu options.
Scan
The Scan key
scans the material in the scanner. For magazines
and books, use this key to scan each page.
Send
The Send key
sends the scanned material to the selected
destination and releases the AXIS 700 for other users. For a single
page/pile of sheets, use this key to scan the material and send the
image in one step.
page/pile of sheets, use this key to scan the material and send the
image in one step.
$;,6
9HUVLRQ ;;;
AXIS 700
User’s Manual
Section 2: Basic Installation
15
Menu
The Menu key
scrolls the menu.
Enter
The Enter key
selects multiple destinations.
Up/Down
The Up
and Down
keys scroll and select menu options.
Cancel
The Cancel key
cancels the scanning process at any stage and
clears any selections made from the menu. It also resets error messages.
Note:
The AXIS 700 will always use the destination and scanning
options most recently shown, whether explicitly selected or not.
Section 2: Basic Installation
AXIS 700 User’s Manual
16
Connecting the AXIS 700 to the Scanner
Caution!
Make sure that the power supply (AXIS PS-C, 12 V DC, 36VA or
AXIS PS-E, 12 V DC, 13,2VA) included in the delivery is marked
with the correct mains voltage.
AXIS PS-E, 12 V DC, 13,2VA) included in the delivery is marked
with the correct mains voltage.
Caution!
Always make sure that power is not connected to any of the units
when making changes to the SCSI chain. The SCSI bus may become
damaged if you connect or disconnect units when power is on.
when making changes to the SCSI chain. The SCSI bus may become
damaged if you connect or disconnect units when power is on.
To connect the AXIS 700 to your scanner, follow these steps:
1. Connect the SCSI cable to the SCSI connector on the AXIS 700.
2. Connect the SCSI cable to the scanner.
3. The AXIS 700 uses a built-in SCSI terminator. Note that the scanner
must also be terminated properly. Refer to the scanner
documentation on how to do this.
documentation on how to do this.
Connecting the AXIS 700 to the Network
Important!
Always consult the Network Administrator before making
changes to the network configuration.
To connect the AXIS 700 to your network, follow these steps:
1. Turn off the AXIS 700 by unplugging the power supply.
2. Connect the network cable to the appropriate network connector,
i.e. RJ-45 for 10baseT and BNC for 10base2, respectively.
3. Power up the scanner.
4. Connect the external power supply to the AXIS 700. The AXIS 700
LED indicators will flash during power up and self test.
Click on the first or last page to see other AR-AX1 (serv.man2) service manuals if exist.