Sharp AR-651 (serv.man25) User Manual / Operation Manual ▷ View online
1
2
3
4
5
6
7
8
9
10
11
12
5-7
To confirm the copy modes stored in the Memor y Number
key, perform steps 3 to 5 on the previous page, then press
the SETTINGS key.
key, perform steps 3 to 5 on the previous page, then press
the SETTINGS key.
Confirming Stored Copy Modes
- The screen on the right is an example of jobs that have been
stored in “MEMORY 2”.
1
2
3
4
5
6
7
8
9
10
11
12
5-8
USING THE SPECIAL FUNCTIONS
MAX
4. BYPASS COPYING
When you want to make copies on thick paper, OHP film, tab paper, tracing paper, sticker labels, use the
sheet bypass. (Only thick and tab papers can be set in the drawer.
sheet bypass. (Only thick and tab papers can be set in the drawer.
Page 2-7)
If the desired size of paper (standard size) is not set in any of the drawers, or if you want to make copies on
non-standard size, make bypass copies.
The modes below are available even in bypass copying if the paper size is specified:
- automatic magnification selection
non-standard size, make bypass copies.
The modes below are available even in bypass copying if the paper size is specified:
- automatic magnification selection
- duplex
- binding margin
- edge erase
- dual-page
- 2 IN 1 / 4 IN 1
- trimming/masking
- mirror image
- staple sort
- magazine sort
- saddle stitch
- hole punch
In there cases, the setting procedures of the following two sizes of paper are different.
- Bypass copying on standard size
- Bypass copying on standard size
Page 5-10
- Bypass copying on non-standard size
Page 5-11
* When copying is finished, the lamp of the //CLEAR ALL key lights.
Either press the //CLEAR ALL key or wait 45 seconds before the bypass copying mode automati-
cally returns to the default mode.
cally returns to the default mode.
* The copier stops its operation when the paper set on the bypass guide has run out even if there is the
same size of copy paper in the drawer. The copier starts again when adding the paper on the bypass
guide before the automatic clear all mode works.
same size of copy paper in the drawer. The copier starts again when adding the paper on the bypass
guide before the automatic clear all mode works.
Bypass copying
The general procedure for making bypass copies (the paper size is not specified) is described below.
* In this case, the paper exits with its copied side up.
* In this case, the paper exits with its copied side up.
1
Set sheets of paper on the bypass guide and align
the slides with the size of the paper.
Ready for bypass feeding
- This message appears:
- Acceptable paper type for bypass copy
Page 2-4
- Place the paper with the side to be copied facing up.
- If you put several sheets on the bypass guide at a time, fan
the papers well before placing it.
- Place the paper so as not to exceed the line indicated on the
slide.
- Do not push the paper forcibly into the entrance of bypass
feeding. It may cause paper jam.
- Draw the triple paper holder depending on the paper size.
- If you put several sheets on the bypass guide at a time, fan
the papers well before placing it.
- Place the paper so as not to exceed the line indicated on the
slide.
- Do not push the paper forcibly into the entrance of bypass
feeding. It may cause paper jam.
- Draw the triple paper holder depending on the paper size.
slide
1
2
3
4
5
6
7
8
9
10
11
12
5-9
4
After selecting the paper type corresponding to the
type of the paper that has been set, press the SET
key.
- When selecting OHP film, the hole punch mode and the staple
mode cannot be used.
3
If the paper other than standard type has been set,
press the PROGRAM key to enter the programme
menu, and press BYPASS FEED key.
- If the standard size paper has been set, you do not have to
perform steps 3 to 4.
2
Place the original(s).
Page 2-9
If you select the paper type not corresponding to the type of the
paper that has been set, it may cause a problem such as a
paper jam, significant image deterioration, etc.
paper that has been set, it may cause a problem such as a
paper jam, significant image deterioration, etc.
5
Press the START key.
- If you press the MEDIA TYPE key on the right menu, which
is displayed when placing paper on the bypass guide, the
menu of step 4 is also displayed.
menu of step 4 is also displayed.
Select other copy modes as required.
1
2
3
4
5
6
7
8
9
10
11
12
5-10
USING THE SPECIAL FUNCTIONS
4. BYPASS COPYING(cont.)
Bypass Copying on Standard Size Paper
1
perform steps 1 to 2 on pages 5-8, 5-9.
-Set the "OTHER" size key as necessary.
Page 5-14
2
Press the key of the same size as the paper that
has been set.
-Non-standard size paper
Page 5-11
If the paper that has been set is a standard size other than A3,
A4, B4, B5, you will select the OTHER key in step 2. In this
case, you need to make the OTHER key recognize the same
size as the paper that has been set.
A4, B4, B5, you will select the OTHER key in step 2. In this
case, you need to make the OTHER key recognize the same
size as the paper that has been set.
3
If you set the paper other than plain paper, press
the MEDIA TYPE key.
4
After selecting the paper type key corresponding
to the type of the paper that has been set, press the
SET key.
If you select the media type key not corresponding to the type
of the paper that has been set, it may cause a problem such as
a paper jam, significant image deterioration and etc.
of the paper that has been set, it may cause a problem such as
a paper jam, significant image deterioration and etc.
5
Press the START key.
Select other copy modes as required.
Click on the first or last page to see other AR-651 (serv.man25) service manuals if exist.