Sharp AR-651 (serv.man15) Service Manual ▷ View online
AR-651/810 DEVELOPER UNIT 12 - 21
[M] Developer unit motor
(1) Remove the rear cover.
(2) Remove the SYS board and hard disk with the
bracket.
(3) Disconnect 1 connector, remove 3 screws,
and take off the developer unit motor with the
bracket.
(4) Remove 2 screws and release the motor from
the bracket.
[N] Developer unit switch
(1) Remove the developer unit, main charger,
cleaner unit and control panel bottom cover.
(2) Disconnect 1 connector, remove 1 screw and
take off the bracket.
(3) Disconnect 2 connectors, remove 1 screw and
take off the developer unit switch.
[O] Toner filter unit
(1) Remove the feed side rear cover.
(2) Pull out the toner filter.
(3) Remove 2 screws and pull out the filter duct.
(4) Disconnect 1 connector of the fan.
(5) Remove 3 screws and take off the fan.
Toner filter
Filter duct
Developer unit motor
Connector
Bracket
Developer unit switch
AR-651/810 DEVELOPER UNIT 12 - 21
[M] Developer unit motor
(1) Remove the rear cover.
(2) Remove the SYS board and hard disk with the
bracket.
(3) Disconnect 1 connector, remove 3 screws,
and take off the developer unit motor with the
bracket.
(4) Remove 2 screws and release the motor from
the bracket.
[N] Developer unit switch
(1) Remove the developer unit, main charger,
cleaner unit and control panel bottom cover.
(2) Disconnect 1 connector, remove 1 screw and
take off the bracket.
(3) Disconnect 2 connectors, remove 1 screw and
take off the developer unit switch.
[O] Toner filter unit
(1) Remove the feed side rear cover.
(2) Pull out the toner filter.
(3) Remove 2 screws and pull out the filter duct.
(4) Disconnect 1 connector of the fan.
(5) Remove 3 screws and take off the fan.
Toner filter
Filter duct
Developer unit motor
Connector
Bracket
Developer unit switch
AR-651/810 DEVELOPER UNIT 12 - 21
[M] Developer unit motor
(1) Remove the rear cover.
(2) Remove the SYS board and hard disk with the
bracket.
(3) Disconnect 1 connector, remove 3 screws,
and take off the developer unit motor with the
bracket.
(4) Remove 2 screws and release the motor from
the bracket.
[N] Developer unit switch
(1) Remove the developer unit, main charger,
cleaner unit and control panel bottom cover.
(2) Disconnect 1 connector, remove 1 screw and
take off the bracket.
(3) Disconnect 2 connectors, remove 1 screw and
take off the developer unit switch.
[O] Toner filter unit
(1) Remove the feed side rear cover.
(2) Pull out the toner filter.
(3) Remove 2 screws and pull out the filter duct.
(4) Disconnect 1 connector of the fan.
(5) Remove 3 screws and take off the fan.
Toner filter
Filter duct
Developer unit motor
Connector
Bracket
Developer unit switch
AR-651/810 DEVELOPER UNIT 12 - 21
[M] Developer unit motor
(1) Remove the rear cover.
(2) Remove the SYS board and hard disk with the
bracket.
(3) Disconnect 1 connector, remove 3 screws,
and take off the developer unit motor with the
bracket.
(4) Remove 2 screws and release the motor from
the bracket.
[N] Developer unit switch
(1) Remove the developer unit, main charger,
cleaner unit and control panel bottom cover.
(2) Disconnect 1 connector, remove 1 screw and
take off the bracket.
(3) Disconnect 2 connectors, remove 1 screw and
take off the developer unit switch.
[O] Toner filter unit
(1) Remove the feed side rear cover.
(2) Pull out the toner filter.
(3) Remove 2 screws and pull out the filter duct.
(4) Disconnect 1 connector of the fan.
(5) Remove 3 screws and take off the fan.
Toner filter
Filter duct
Developer unit motor
Connector
Bracket
Developer unit switch