Sharp AR-235 (serv.man9) Service Manual ▷ View online
AR-235/275 SIMULATION - 20
A4/LT (8.5" x 11") detection enable/disable setup
In the inch series, Letter is detected as A4; in the AB series, A4 is detected as Letter.
Detection size when A4/LT (8.5" x 11") document/paper is used.
Operation/procedure (Pattern 1)
Set the auditor.
Operation/procedure (Pattern 2)
Used to set the count up number (1 or 2) when an A3/WLT paper
passes through.
passes through.
For the drum counter and the developer counter, double count is
employed unconditionally.
employed unconditionally.
(Target counter selection)
Used to set the count up number of the selected counter.
Operation/procedure (Pattern 1)
Select the destination.
Operation/procedure
The current setup is displayed with ON or OFF.
Enter an input (20 digits) of the NETWORK soft key and press the [OK]
key, and the collating result is displayed with OK or NG.
key, and the collating result is displayed with OK or NG.
When "0" is entered to the soft key, it is treated as a trial setup.
Set value
Setup
Remarks
0
Detection invalid
Default
1
Detection valid
Employed unit
Destination
Document size
Set value
0
(Invalid)
1
(Valid)
Document
Document
table/SPF
table/SPF
AB series
A4
A4
LT (8.5” x 11”)
LT (8.5” x 11”)
A4
LT (8.5” x 11”)
Inch series
A4
LT (8.5” x 11”)
A4
LT (8.5” x 11”)
LT (8.5” x 11”)
A4
Paper
Machine paper
feed cassette
feed cassette
All destinations
–
Set with key operations.
Manual paper
feed tray
feed tray
All destinations
–
Regardless of the simulation
setup.
26-3
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the specifications of the auditor. Setting
must be made depending on the use condition of the
auditor.
must be made depending on the use condition of the
auditor.
Section
Auditor
Item
Specifications
Display
items
Content
Setting
range
Default
0:P10
Built-in auditor mode
0-2
0
1:VENDOR
Coin vendor mode
2:OTHER
Others
26-5
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the count mode of the total counter and the
maintenance counter.
maintenance counter.
Item
SpecificationsCounter
1:TOTAL COUNTER
Total
2:MAINTE COUNTER
Maintenance
1:SINGLE COUNT
Single count
2:DOUBLE COUNT
Double count
Setting range
1-2
Default
2
(Initial screen)
(Input screen)
Sim26-3 AUDITOR SET
AUDITOR 0
(0:P10 1:VENDOR
2:OTHER)
[ 0- 2]
0
Sim26-5 COUNT MODE
1:TOTAL COUNTER 1
2:MAINTE COUNTER 1
2
Sim26-5 COUNT MODE
2:MAINTE COUNTER 1
(1:SINGLE COUNT
2:DOUBLE COUNT)
[ 1- 2]
1
26-6
Purpose
Setting
Function (Purpose)
Used to set the specifications depending on
the destination.
the destination.
Item
SpecificationsDes
tination
Display
items
Content
Setting
range
Default
0:JAPAN
Japan
0-13
0
1:SEC
SEC
2:SECL
SECL
3:SEEG
SEEG
4:SUK
SUK
5:SCA
SCA
6:SEF
SEF
7:INEG
EX inch series
8:ABEG
EX AB series
9:INEF
EX inch series (FC)
10:ABEF
EX AB series (FC)
11:CHINESE
China
12:TAIPEI
Taiwan
13:SEEG2
SEEG2
26-10
Function
(Purpose)
(Purpose)
Used to enter the Software Key for the Network
Scanner. (Setup is allowed only when the PCL board is
installed.
Scanner. (Setup is allowed only when the PCL board is
installed.
(Initial screen)
(In case of OK)
(In case of NG)
Sim26-6 DESTINATION
DESTINATION 0
(0:JAPAN 1:SEC
2:SECL 3:SEEG 4:SUK
1/3 [ 0- 13]
0
Sim26-10 SCANNERKEY
SCANNER KEY ON
----------
----------
Sim26-10 SCANNERKEY
SCANNER KEY OK
----------
----------
Sim26-10 SCANNERKEY
SCANNER KEY NG
----------
AR-235/275 SIMULATION - 21
After canceling the simulation, if OK, the scanner function is enable; if
NG, the scanner function is disabled.
NG, the scanner function is disabled.
This setting must be reset after the simulation cancel.
Note: Executable only when the SCANNER is installed.
Operation/procedure
The current setup is displayed with ON or OFF.
Enter an input (20 digits) of the E-MAIL RIC soft key and press the
[OK] key, and the collating result is displayed with OK or NG.
[OK] key, and the collating result is displayed with OK or NG.
After canceling the simulation, if OK, the E-MAIL RIC function is
enable; if NG, the E-MAIL RIC function is disabled.
enable; if NG, the E-MAIL RIC function is disabled.
This setting must be reset after the simulation cancel.
Note: Executable only when the PCL/NIC is installed.
Operation/procedure
The current setup is displayed with ON or OFF.
Enter an input (20 digits) of the PS expansion kit soft key and press the
[OK] key, and the collating result is displayed with OK or NG.
[OK] key, and the collating result is displayed with OK or NG.
After canceling the simulation, if OK, the PS expansion kit function is
enable; if NG, the PS expansion kit function is disabled.
enable; if NG, the PS expansion kit function is disabled.
This setting must be reset after the simulation cancel.
Note: Executable only when the PCL/PS3 is installed.
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Note: Executable only when the finisher is not installed.
Operation/procedure (Pattern 1)
Select the language to be used according to the table below.
This setup varies in connection with SIM 26-6 (Destination setup).
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
This setup varies in connection with SIM 26-6 (Destination setup).
26-12
Function
(Purpose)
(Purpose)
Used to input the Software Key for E-MAIL RIC.
(Initial screen)
(In case of OK)
(In case of NG)
26-14
Function
(Purpose)
(Purpose)
Used to input the Software Key for the PS extention kit.
(Initial screen)
(In case of OK)
(In case of NG)
26-18
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set enable/disable of toner save operation.
Item
SpecificationsOperation mode (Common)
Display
items
Content
Setting
range
Default
0:OFF
Disable
0-1
0
1:ON
Enable
Note
Setup is allowed only for Japan and UK.
Sim26-12 E-MAIL KEY
E-MAIL KEY ON
----------
----------
Sim26-12 E-MAIL KEY
E-MAIL KEY OK
----------
----------
Sim26-12 E-MAIL KEY
E-MAIL KEY NG
----------
----------
Sim26-14 PS KIT KEY
PS KIT KEY ON
----------
----------
Sim26-14 PS KIT KEY
PS KIT KEY OK
----------
----------
Sim26-14 PS KIT KEY
PS KIT KEY NG
----------
----------
Sim26-18 TONER SAVE
TONER SAVE MODE 0
(0:OFF 1:ON)
[ 0- 1]
0
26-20
Function
(Purpose)
(Purpose)
Used to set the job separator paper exit mode.
Display
items
Content
Setting
range
Default
0:OFF
Paper is discharged to No. 1
paper exit port.
paper exit port.
0-1
0
1:ON
Used to discharge paper to the
job separator tray (No. 2 paper
exit port).
job separator tray (No. 2 paper
exit port).
26-22
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the specification (language display) for the
destination.
destination.
Item
Specifications
Display items
Setting
range
Default
0:JAPANESE
10:TURKISH
0-19
0
1:ENG.US
11:GREEK
2:ENG.UK
12:POLISH
3:FRENCH
13:HUNGARIAN
4:GERMAN
14:CZECHOSLOVAK
5:ITALY
15:RUSSIAN
6:DUTCH
16:FINNISH
7:SWEDISH
17:NORWEGIAN
8:SPANISH
18:DANISH
9:PORTUGUESE
19:CHINESE
26-30
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the operation mode for CE mark.
Item
SpecificationsOperation mode (Common)
Sim26-20 JOBSEP OUT
JOBSEP OUT MODE 0
(0:OFF 1:ON)
[ 0- 1]
0
Sim26-22 LANGUAGE
LANGUAGE 0
(0:JAPANESE
1:ENG.US 2:ENG.UK
1/3 [ 0- 19]
0
Sim26-30 CE MARK
CE MARK CONTROL 0
(0:OFF 1:ON)
[ 0- 1]
0
AR-235/275 SIMULATION - 22
Operation/procedure (Pattern 1)
Used to set whether the trouble history of SIM 22-4 is displayed as
one-time trouble or as a number of times of troubles continuously
occurred when two or more troubles of the same kind occurred.
one-time trouble or as a number of times of troubles continuously
occurred when two or more troubles of the same kind occurred.
Enter the set value with 10-key, and press [OK] key.
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Note: Executable only with SRU (AR models).
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Note: Executable only with CRU (DM models).
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Note: Executable only with CRU (DM models).
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Note: Executable only when the finisher is installed.
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key, and the
LCD contrast will be immediately changed and displayed.
LCD contrast will be immediately changed and displayed.
Display items
Setting range
Default
Japan, SEC, SECL,
SCA, SEF, Taiwan
Others
0:OFF
0-1
0
1
1:ON
26-35
Purpose
Setup
Function
(Purpose)
(Purpose)
Used to set the mode of trouble memory.
Item
Specifications
Display item
Content
Set range
Default
0:ONCE
When two or more troubles
occur, only one is registered.
occur, only one is registered.
0-1
0
1:ANY
All the troubles occurred are
registered.
registered.
26-36
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set whether to stop when the maintenance life
is reached.
is reached.
Item
Operation
Display items
Content
Setting range
Default
0:STOP
Stop
0-1
1
1:NON STOP
Non stop
26-37
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set whether to stop when the developer life is
reached.
reached.
Item
Operation
Display items
Content
Setting range
Default
0:STOP
Stop
0-1
0
1:NON STOP
Non stop
Sim26-35 TROUBLE
TROUBLE MODE 0
(0:ONCE 1:ANY)
[ 0- 1]
0
Sim26-36 MAINTESTOP
MAINTENANCE OVER 0
(0:STOP
1:NON STOP)
[ 0- 1]
0
Sim26-37 DEVE. STOP
DEVE. LIFE OVER 0
(0:STOP
1:NON STOP)
[ 0- 1]
0
26-38
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set whether to stop when the drum life is
reached.
reached.
Item
Operation
Display items
Content
Setting range
Default
0:STOP
Stop
0-1
0
1:NON STOP
Non stop
26-46
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set whether to meet with the output direction of
images regardless of the mode when installing the
finisher.
images regardless of the mode when installing the
finisher.
Item
Operation
Display items
Content
Setting range
Default
0:OFF
Setting No
0-1
0
1:ON
Setting Yes
26-50
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set whether to use the black/white reverse
function.
function.
Item
Operation
Display
items
Content
Setting
range
Default
0:ON
Enable
0-1
0
1:OFF
Disable
26-54
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the PWM duty (brightness) at the center
value of the LCD contrast.
value of the LCD contrast.
Item
Operation
Setting range
30-70
Default
50
Sim26-38 DRUM STOP
DRUM LIFE OVER 0
(0:STOP
1:NON STOP)
[ 0- 1]
0
Sim26-46 OUT DIR
OUT DIRECTION 0
(0:OFF 1:ON)
[ 0- 1]
0
Sim26-50 B/W REV.
B/W REVERSE 0
(0:ON 1:OFF)
[ 0- 1]
0
Sim26-54 LCD DUTY
LCD PWM DUTY 0
[ 30- 70]
0
AR-235/275 SIMULATION - 23
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
If a model different from CPM setup (22cpm or 27cpm) of BOOT is set,
a system error will occur after canceling the simulation.
a system error will occur after canceling the simulation.
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
This setup varies in connection with SIM 26-6 (Destination setup).
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Operation/procedure
Current memory is displayed in PRESENT column.
Enter a value (max. 8 digits) with the 10-key, and press the [OK] key.
The input number is displayed instead of "NEW".
The set value is stored and "PRESENT" of LCD is revised.
Operation/procedure
The operating conditions of sensors and detectors in the different sec-
tions than the paper feed section of the machine are displayed. The
active sensors and detectors are highlighted.
tions than the paper feed section of the machine are displayed. The
active sensors and detectors are highlighted.
26-57
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the model code.
Item
Operation
Display items
Setting range
Default
1:AR-235
1-10
1
2:AR-255S
3:AR-255P
4:AR-255F
5:AR-255FP
6:AR-275
7:AR-N275
8:DM-2305
9:DM-2515
10:DM-2705
26-60
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set enable/disable of the FAX mode key when
FAX is not installed. (When FAX is installed, the FAX
mode is enabled regardless of this setup.)
FAX is not installed. (When FAX is installed, the FAX
mode is enabled regardless of this setup.)
Item
Operation
Display
items
Content
Setting
range
Default
JAPAN,
SEC, SECL,
SUK, SCA
Others
0:ON
Effective (The
message with FAX
uninstalled is
displayed.)
message with FAX
uninstalled is
displayed.)
0-1
0
1
1:OFF
Disable (Error Beep)
27
27-1
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set PC/MODEM communication trouble (U7-
00) detection Yes/No.
00) detection Yes/No.
Section
Communication (RIC/MODEM)
Item
SpecificationsOperation mode
(Common)
Sim26-57 MACHINE
MACHINE CODE 1
(1:AR-235
2:AR-255S
1/5 [ 1-10]
1
Sim26-60 FAX KEY
FAX KEY SETTING 0
(0:ON 1:OFF)
[ 0- 1]
0
Display
items
Content
Setting
range
Default
0:OFF
In case of the communication
trouble, U7-00 is not displayed.
trouble, U7-00 is not displayed.
0-1
0
1:ON
In case of the communication
trouble, U7-00 is displayed.
trouble, U7-00 is displayed.
27-5
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to enter the TAG No. of the copier.
Item
Data
30
30-1
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of sensors and detectors
in the sections other than the paper feed section of the
copier and the related circuit. (The operation of
sensors and detectors can be monitored with the
LCD.)
in the sections other than the paper feed section of the
copier and the related circuit. (The operation of
sensors and detectors can be monitored with the
LCD.)
Section
Others
Item
Operation
PPD1H
PS paper detection 1 sensor
PPD1L
PS paper detection 2 sensor
PPD2
Duplex sensor
POD1
1st paper exit paper out sensor
DVCH
Developing cartridge detection sensor
DRST
Drum intial detection sensor
DSWR1
Interlock switch (side door)
SFTHP
Shifter home position sensor
POD2
2nd paper exit paper out sensor
TOPF
2nd paper exit full detection sensor
DSWR0
2nd paper exit cover open/close detection sensor
LOEMP
1st paper exit empty detection sensor
Sim27-1 U7-00 SET.
DISABLE U7-00 0
(0:OFF 1:ON)
[ 0- 1]
0
Sim 27-5 TAG# SET.
TAG# SETTING
PRESENT :
NEW :
12345678
Sim30-1 MAIN SENSOR
PPD1H PPD1L
PPD2
POD1 DVCH DRST
DSWR1
SFTHP
POD2
TOPF DSWR0 LOEMP
Click on the first or last page to see other AR-235 (serv.man9) service manuals if exist.