Sharp AR-235 (serv.man9) Service Manual ▷ View online
AR-235/275 SIMULATION - 16
Operation/procedure
Key operetion code is displayed.
Operation/procedure
The data shows the use frequency of each section.
Operation/procedure
The data shows the use frequency of each paper feed section.
Operation/procedure
The detected machine composition is displayed.
NONE: "- - - - - - - - -" is displayed.
[ ]: Shows the product code in the list below.
*1: Installed quantity is displayed in ( ).
For the cassettes, only the option cassette is displayed.
Operation/procedure
The current counter value (number of send/receive pages) of the FAX
send/receive counter and the accumulated reception time and the print
counter are displayed.
send/receive counter and the accumulated reception time and the print
counter are displayed.
Note: Executable only when the FAX is installed.
Operation/procedure
Fourty SPF JAM history datas are displayed sequentially from the lat-
est.
est.
22-7
Purpose
User data output/Check (Display/Print)
Function
(Purpose)
(Purpose)
Used to display the key operator code
Item
Data
User data
22-8
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to check the number of use of the staple, the
SPF, and scanning.
SPF, and scanning.
Item
Counter
SPF
SPF counter
SCAN
Scan counter
STAPLE
Stapler counter
22-9
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to check the number of use of each paper feed
section. (the number of prints)
section. (the number of prints)
Section
Paper feed
Item
Counter
BYPASS
Manual feed counter
TRAY3
Tray 3 counter
TRAY1
Tray 1 counter
TRAY4
Tray 4 counter
TRAY2
Tray 2 counter
22-10
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to check the system configulation.
Item
SpecificationsOption
Sim22-7 KEY OPE
KEY OPE CODE: nnnnn
Sim22-8 ORG./STAPLE
SPF : nnnnnnn
SCAN : nnnnnnn
STAPLE : nnnnnnn
Sim22-9 FEED 1/2
BYPASS : nnnnnnn
TRAY1 : nnnnnnn
TRAY2 : nnnnnnn
TRAY3 : nnnnnnn
Display items
Display items
SPEED
23CPM/25CPM/27CPM
DF
NONE/[1: SPF]/[2: RSPF]
OUTPUT
NONE/[3: Finisher]/[4: Job separator]
CASETTE1
NONE/[5: One-step paper feed unit]
CASETTE2
NONE/[6: Two-step paper feed unit]
IMC MEM
NONE/Expansion memory capacity (MB)
PCL
NONE/[7: PCL]
PS3
NONE/[8: PS3]
NIC
NONE/[9: NIC]
SCANNER
NONE/[10: SCANNER]
FAX
NONE/[11: FAX]
FAX MEM
NONE/Memory capacity (MB)
HAND SET
NONE/[12: Handset]
No.
Item
Model code
AR model
DM model
1
SPF
AR-SP4
DM-SP2
2
RSPF
AR-RP3
DM-RP1
3
Finisher
AR-FN5
DM-FN1
4
Job separator
AR-TR3
STANDARD
5
1 tray paper feed unit
AR-D11 (*1)
DM-DE3 (*1)
6
2 tray paper feed unit
AR-D12 (*1)
DE-DE4 (*)
7
PCL
AR-P11
STANDARD
8
PS3
AR-PK1
STANDARD
9
NIC
AR-NC5J
STANDARD
10
SCANNER
AR-NS2
DM-NS1
11
FAX
AR-FX4
DM-FX2
12
Handset
AR-HN4
–
22-11
Purpose
Adjustment/Setting/Check
Function
(Purpose)
(Purpose)
FAX related counter display
22-12
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to check the misfeed positions and the number of
misfeed at each position. (When the number of
misfeed is considerably great, it can be judged as
necessary for repair.)
misfeed at each position. (When the number of
misfeed is considerably great, it can be judged as
necessary for repair.)
Section
SPF
Item
Trouble
Mis-feed
Sim22-10 SYSTEM 1/4
SPEED : XXXXXXX
DF : XXXXXXX
OUTPUT : XXXXXXX
CASETTE1: XXXXXXX
AR-235/275 SIMULATION - 17
Operation/procedure
Counter data is displayed.
Operation/procedure (Pattern 7)
Each counter is cleared individually. (The history of each counter is
deleted when clearing)
deleted when clearing)
Operation/procedure (Pattern 7)
Clear the counters individually.
Operation/procedure (Pattern 7)
Clear the counters individually.
Operation/procedure (Pattern 6)
Press the [OK] key.
Operation/procedure (Pattern 6)
Press the [OK] key.
Display items
Jam contents
PI_TOP
SPF paper-in lead edge jam
PI_END
SPF paper-in rear edge jam
PO_TOP
SPF paper-out lead edge jam
PO_END
SPF paper-out rear edge jam
JAM_REV
SPF duplex reversion jam
ORG_SHORT
SPF short scale error
ORG_LONG
SPF long scale error
22-19
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to display the scanner mode counter.
Item
Trouble
SCANMODE
Scanner mode counter
24
24-1
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to clear the misfeed counter, the misfeed history,
the trouble counter, and the trouble history. (The
counters are cleared after completion of maintenance.)
the trouble counter, and the trouble history. (The
counters are cleared after completion of maintenance.)
Item
Counter
(Initial screen)
(Check screen)
1:JAM
JAM counter/JAM history
2:SPF JAM
SPF JAM counter/SPF JAM history
3:TROUBLE
Trouble counter/Trouble history
24-2
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to clear the number of use (the number of prints)
of each paper feed section.
of each paper feed section.
Section
Paper feed
Item
Counter
Sim22-12 SPF JAM1/5
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
XXXXXXX XXXXXXX
Sim22-19 SCAN MODE
SCANMODE:nnnnnnnnn
Sim24-1 COUNTER CLR
1:JAM
2:SPF JAM
3:TROUBLE
2
Sim24-1 COUNTER CLR
1:JAM
2:
SPF JAM
3:TROUBLE
ARE YOU SURE?
2
(Initial screen)
(Check screen)
1:BYPASS
Manual feed counter
4:TRAY3
Tray 3 counter
2:TRAY1
Tray 1 counter
5:TRAY4
Tray 4 counter
3:TRAY2
Tray 2 counter
24-3
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to clear the number data of use of the staple, the
SPF and scanning.
SPF and scanning.
Item
Counter
(Initial screen)
(Check screen)
1:SPF
SPF counter
2:SCAN
Scan counter
3:STAPLE
Stapler counter
24-4
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to reset the maintenance counter.
Item
Counter
(Initial screen)
(Check screen)
24-5
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to reset the developer counter. (The developer
counter of the DV unit which is installed is reset.)
counter of the DV unit which is installed is reset.)
Section
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Developer/Toner hopper
Cleaning)
Developer/Toner hopper
Item
Counter
Developer
(Initial screen)
(Check screen)
24-6
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to reset the copy counter.
Item
Counter
Copier
Sim24-2 COUNTER CLR
1:BYPASS 4:TRAY3
2:TRAY1 5:TRAY4
3:TRAY2
2
Sim24-2 COUNTER CLR
1:BYPASS 4:TRAY3
2:
TRAY1
5:TRAY4
3:TRAY2
ARE YOU SURE?
2
Sim24-3 COUNTER CLR
1:SPF
2:SCAN
3:STAPLE
2
Sim24-3 COUNTER CLR
1:SPF
2:
SCAN
3:STAPLE
ARE YOU SURE?
2
Sim24-4 COUNTER CLR
MAINTENANCE COUNTER
CLEAR
PRESS OK KEY
Sim24-4 COUNTER CLR
MAINTENANCE COUNTER
CLEAR
ARE YOU SURE?
Sim24-5 COUNTER CLR
DEVELOPER COUNTER
CLEAR
PRESS OK KEY
Sim24-5 COUNTER CLR
DEVELOPER COUNTER
CLEAR
ARE YOU SURE?
AR-235/275 SIMULATION - 18
Operation/procedure (Pattern 6)
Press the [OK] key.
Operation/procedure (Pattern 6)
Press the [OK] key.
Operation/procedure (Pattern 7)
Clear the counters individually.
Operation/procedure
The current counter value (number of send/receive pages) of the FAX
send/receive counter and the accumulated reception time and the print
counter are cleared to 0.
send/receive counter and the accumulated reception time and the print
counter are cleared to 0.
Note: Executable only when the FAX is installed.
Operation/procedure (Pattern 6)
Press the [OK] key.
The scanner mode counter and the number of send of the scanner are
cleared.
cleared.
Operation/procedure
The operation of the drive system is checked.
Toner density control sensor value is displayed.
Select the mode with the 10-key and press the [OK] key, and the main
motor will rotate and the toner concentration control sensor value will
be displayed.
motor will rotate and the toner concentration control sensor value will
be displayed.
After execution, interruption cannot be made for about 7 sec. ([CA] key,
[INTERRUPT] key, and [BACK] key are invalid.)
[INTERRUPT] key, and [BACK] key are invalid.)
Operation/procedure
1) Open the cover.
2) Power ON. (The mechanism cannot be initialized because the
cover is open.)
3) Install the developing unit with new developer in it.
4) Enter SIM 25-2.
5) Close the cover immediately before starting the operation.
6) Press the [OK] key to start.
Sampling is made 54 times every 600ms, and the average of the last
three times in the last 1.8sec of 3min is stored.
three times in the last 1.8sec of 3min is stored.
When "EE-EU" or "EE-EL" after completion, an error display is shown.
EU error occurs when the finally calculated toner concentration refer-
ence value is 179 or greater.
ence value is 179 or greater.
EL error occurs when the finally calculated toner concentration refer-
ence value is 77 or smaller.
ence value is 77 or smaller.
(Initial screen)
(Check screen)
24-7
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to clear the OPC drum (membrane decrease)
correction counter. (This simulation is executed when
the OPC drum is replaced.
correction counter. (This simulation is executed when
the OPC drum is replaced.
Section
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Photo conductor
Cleaning)
Photo conductor
Item
Counter
(Initial screen)
(Check screen)
24-9
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to clear the printer print counter. (The counter is
cleared after completion of maintenance.)
cleared after completion of maintenance.)
Section
Printer
Item
Counter
Printer
(Initial screen)
(Check screen)
1:PRINTER
Printer counter
2:IMC
IMC counter
3:DUPLEX
DUPLEX counter
4:OTHERS
The other counters
24-10
Purpose
Adjustment/Setting/Check
Function
(Purpose)
(Purpose)
FAX related counter clear
24-15
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to clear the scanner mode counter.
Item
Counter
Sim24-6 COUNTER CLR
COPIES COUNTER
CLEAR
PRESS OK KEY
Sim24-6 COUNTER CLR
COPIES COUNTER
CLEAR
ARE YOU SURE?
Sim24-7 COUNTER CLR
DRUM COUNTER CLEAR
PRESS OK KEY
Sim24-7 COUNTER CLR
DRUM COUNTER CLEAR
ARE YOU SURE?
Sim24-9 COUNTER CLR
1:PRINTER 4:OTHERS
2:IMC
3:DUPLEX
2
Sim24-9 COUNTER CLR
1:PRINTER 4:OTHERS
2:
IMC
3:DUPLEX
ARE YOU SURE?
2
(Initial screen)
(Process check screen)
25
25-1
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the main drive
(excluding the scanner section) and to check the
operation of the toner concentration sensor. (The toner
concentration sensor output can be monitored.)
(excluding the scanner section) and to check the
operation of the toner concentration sensor. (The toner
concentration sensor output can be monitored.)
Section
DRIVE
Item
Operation
(Initial screen)
(Executing screen)
25-2
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to make the initial setting of toner concentration
when replacing developer.
when replacing developer.
Section
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Developer/Toner hopper
Cleaning)
Developer/Toner hopper
Sim24-15 COUNTERCLR
SCANNER MODE
COUNTER CLEAR
PRESS OK KEY
Sim24-15 COUNTERCLR
SCANNER MODE
COUNTER CLEAR
ARE YOU SURE?
Sim25-1 MAIN MOTOR
1:600dpi
2:1200dpi
EXEC
2
Sim25-1 MAIN MOTOR
1:600dpi
2:
1200dpi
[128]
EXEC
2
AR-235/275 SIMULATION - 19
Note: After completion of execution, be sure to press the [CA] key to
cancel the simulation.
[CRUM-related error cancel procedure]
• When “CRUM DEVICE ERROR” is displayed:
• "CRUM DATA ERROR"
• "DEVE UNIT NONE"
• "TONER UNIT NONE"
• "EU ERROR"
• "EL ERROR"
Operation/procedure (Pattern 1)
Set the job separator.
Operation/procedure (Pattern 2)
Used to set the automatic size detection.
8.5" x 13" detection valid/invalid setup
Detection size when 8.5" x 13" document/paper is used.
(Initial screen)
(Executing screen)
Error content:
Occurs in case of a communication error
between the machine and CRUM.
between the machine and CRUM.
Cancel procedure: Reset with [CA] key and cancel with SIM 16.
Error content:
CRUM identification error, CRUM model error,
CRUM type error, CRUM destination error
CRUM type error, CRUM destination error
Cancel procedure: Install the CRUM which is satisfactory with the
machine setup, reset with the [CA] key, and
execute SIM 25-2 again.
execute SIM 25-2 again.
Error content:
Occurs when the developing unit is not installed
in an AR model.
in an AR model.
Cancel procedure: It returns to the state before execution of auto
developer adjustment. It is canceled by the
operations of Cover open
operations of Cover open
→
Developing unit
installation
→
Cover close. Therefore, developer
adjustment is started by pressing [OK] key.
Error content:
Occurs when the CRUM is not installed in a DM
model.
model.
Cancel procedure: It returns to the state before execution of auto
developer adjustment. It is canceled by the
operations of Cover open
operations of Cover open
→
CRUM installation
→
Cover close. Therefore, developer adjustment is
started by pressing [OK] key.
started by pressing [OK] key.
Error content:
Occurs when the toner concentration reference
value calculated in developer adjustment finally
is 179 or greater.
value calculated in developer adjustment finally
is 179 or greater.
Cancel procedure: Reset with [CA] key and execute SIM 25-2 again.
Error content:
Occurs when the toner concentration reference
value calculated in developer adjustment finally
is 77 or smaller.
value calculated in developer adjustment finally
is 77 or smaller.
Cancel procedure: Reset with [CA] key and execute SIM 25-2 again.
Sim25-2 AUTO DV ADJ
AUTO DEVE ADJUST
PRESS OK KEY EXEC
Sim25-2 AUTO DV ADJ
AUTO DEVE ADJUST
[128]
EXEC
26
26-1
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set options. (This simulation is used to make
option setting when an option is installed.)
option setting when an option is installed.)
Item
SpecificationsOption
Set value
Connection option
0
None (default)
1
Job separator provided.
26-2
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to detect the paper size.
Section
Paper feed
Item
Specifications
1:B4/LG,FC
Setting to detect B4/Legal as FC
0 : B4 legal is detected as B4 legal.
1 : B4 legal is detected as FC.
0 : B4 legal is detected as B4 legal.
1 : B4 legal is detected as FC.
2:A4<->LT
This setup detects Letter as A4 in the inch series and
A4 as Letter in the AB series.
0 : Detection disable
1 : Detection valid
A4 as Letter in the AB series.
0 : Detection disable
1 : Detection valid
(Initial screen)
(Input screen)
Set value
Setup
Remarks
0
Detection invalid
Default
1
Detection valid
Sim26-1 OPTION SET.
JOB SEPARATOR 0
(0:NONE
1:JOB SEPARATOR)
[ 0- 1]
0
Sim26-2 SIZE SET
1:B4/LG,FC 0
2:A4<->LT 0
1
Sim26-2 SIZE SET
1:B4/LG,FC 0
(0:OFF 1:ON)
[ 0- 1]
1
Employed unit
Destination
Document size
Set value
0
(Invalid)
1
(Valid)
Document
Document
table/SPF
table/SPF
AB series (Japan)
FC (8.5” x 13”)
B4
B4
LG (8.5” x 14”)
B4
B4
B4
B4
B4
AB series
FC (8.5” x 13”)
B4
FC (8.5” x 13”)
LG (8.5” x 14”)
B4
FC (8.5” x 13”)
B4
B4
FC (8.5” x 13”)
Inch series
FC (8.5” x 13”)
LG (8.5” x 14”)
FC (8.5” x 13”)
LG (8.5” x 14”)
LG (8.5” x 14”)
FC (8.5” x 13”)
B4
WLT (11” x 17”)
WLT (11” x 17”)
Paper
Machine paper
feed cassette
feed cassette
All destinations
–
Set with key operations.
Manual paper
feed tray
feed tray
Japan (AB series)
FC (8.5” x 13”)
LG (8.5” x 14”)
LG (8.5” x 14”)
LG (8.5” x 14”)
LG (8.5” x 14”)
LG (8.5” x 14”)
B4
B4
B4
AB series
FC (8.5” x 13”)
LG (8.5” x 14”)
FC (8.5” x 13”)
LG (8.5” x 14”)
LG (8.5” x 14”)
FC (8.5” x 13”)
B4
B4
B4
Inch series
FC (8.5” x 13”)
LG (8.5” x 14”)
FC (8.5” x 13”)
LG (8.5” x 14”)
LG (8.5” x 14”)
FC (8.5” x 13”)
B4
B4
B4
Click on the first or last page to see other AR-235 (serv.man9) service manuals if exist.