Sharp AR-203 (serv.man5) Service Manual ▷ View online
AR-203E/5420/M200/M201 SIMULATION, TROUBLE CODES 10 - 28
50
06
Copy lead edge position
adjustment (SPF/RSPF)
(Only the AR-203E/M200/
M201 with the SPF/RSPF
installed)
adjustment (SPF/RSPF)
(Only the AR-203E/M200/
M201 with the SPF/RSPF
installed)
[Function]
Used to adjust the SPF/RSPF copy lead edge.
Used to adjust the SPF/RSPF copy lead edge.
When the adjustment value of the document scan position adjustment is increased by 1, the
scan start timing is advanced by 0.1mm.
scan start timing is advanced by 0.1mm.
The print result is shifted to the opposite direction of the scan start position.
The adjustment mode can be changed by pressing [Exposure mode selector] key (or [
] [
]
key for the AR-M200/M201). (Adjustment range: 1 – 99, Default: 50)
When scanning a back surface of document, the mode must be changed to operate the SPF/
RSPF by pressing [2-SIDED SCAN]/[2-SIDED COPY] key.
RSPF by pressing [2-SIDED SCAN]/[2-SIDED COPY] key.
∗ When there is no document in the SPF/RSPF, copy is inhibited.
∗ When paper is discharged, the shifter is operated.
∗ When paper is discharged, the shifter is operated.
[Operation]
The operation is similar to simulation 46-01.
The operation is similar to simulation 46-01.
10
Center offset adjustment
[Function]
Used to adjust the center offset position of copy images on copy paper and that in scanning
document.
When this simulation is executed, the current set value is displayed.
Enter the adjustment value and press [START] key to save the setting and make a copy. (When
the set value is changed by 1, the center is shifted by 0.1mm.)
When the adjustment value is increased, the center is shifted to right. When decreased, the
center is shifted to left.
The modes can be selected by pressing [Exposure mode selector] key
Used to adjust the center offset position of copy images on copy paper and that in scanning
document.
When this simulation is executed, the current set value is displayed.
Enter the adjustment value and press [START] key to save the setting and make a copy. (When
the set value is changed by 1, the center is shifted by 0.1mm.)
When the adjustment value is increased, the center is shifted to right. When decreased, the
center is shifted to left.
The modes can be selected by pressing [Exposure mode selector] key
(or [
] [
] key for the
AR-M200/M201).
When the set value is changed largely, the area outside the shading area may be scanned to
cause black streaks on the edges. When the SPF/RSPF is used, select the mode for use of the
SPF/RSPF by [2-SIDED SCAN]/[2-SIDED COPY] key.
When the set value is changed largely, the area outside the shading area may be scanned to
cause black streaks on the edges. When the SPF/RSPF is used, select the mode for use of the
SPF/RSPF by [2-SIDED SCAN]/[2-SIDED COPY] key.
(*): Support for the installation models. For non-installation models, skip.
(**): For Simplex models, skip.
* When printing with the manual paper feed tray, use paper of the letter size.
* When printing with the manual paper feed tray, use paper of the letter size.
* In the 2nd print center offset adjustment, print is made forcibly as 1to2/Short Edge from OC
regardless of duplex setting.
* When paper is discharged, the shifter is operated.
[Operation]
The operation is similar to simulation 46-01.
The operation is similar to simulation 46-01.
Main
code
code
Sub
code
Contents
Details of function/operation
Mode
Initial value
of duplex
setting
Display item
(AR-M200/
M201)
LED
(AR-M200/
M201)
Display lamp
(AR-203E)
Default
Front surface
document scan
position adjustment
document scan
position adjustment
S-S
SIDE1
COPY mode
lamp
lamp
AE mode
lamp
lamp
50
Back surface
document scan
position adjustment
(AR-M200/M201)
document scan
position adjustment
(AR-M200/M201)
D-S
SIDE2
PRINT mode
lamp
lamp
—
50
Rear edge void
adjustment (RSPF)
adjustment (RSPF)
S-S
END
SCAN mode
lamp
lamp
PHOTO
mode lamp
mode lamp
50
Mode
Display item
(AR-M200/M201)
LED
(AR-M200/M201)
Display lamp
(AR-203E/5420)
Default
Print center offset
(Main cassette
paper feed)
(Main cassette
paper feed)
TRAY1
COPY mode lamp
Main cassette lamp
Main cassette lamp
AE mode lamp
Main cassette lamp
Main cassette lamp
50
(*) Print center offset
(2nd cassette paper
feed)
(2nd cassette paper
feed)
TRAY2
COPY mode lamp
2nd cassette lamp
2nd cassette lamp
AE mode lamp
2nd cassette lamp
2nd cassette lamp
50
Print center offset
(Manual paper feed)
(Manual paper feed)
MFT
COPY mode lamp
Manual paper feed
lamp
Manual paper feed
lamp
AE mode lamp
Manual paper feed
lamp
Manual paper feed
lamp
50
(**) 2nd print center
offset (Main cassette
paper feed)
offset (Main cassette
paper feed)
SIDE2
PRINT mode lamp
Main cassette lamp
Main cassette lamp
TEXT mode lamp
Main cassette lamp
Main cassette lamp
50
AR-203E/5420/M200/M201 SIMULATION, TROUBLE CODES 10 - 29
50
12
Document off-center
adjustment
adjustment
[Function]
Used to adjust document scan off-center adjustment.
The adjustment modes can be selected by pressing [Exposure mode selector] key
Used to adjust document scan off-center adjustment.
The adjustment modes can be selected by pressing [Exposure mode selector] key
(or [
]
[
] key for the AR-M200/M201). (Adjustment range: 1 – 99, Default: 50)
When the adjustment value is increased, the print result is shifted to left.
* When paper is discharged, the shifter is operated.
[Operation]
The operation is similar to simulation 46-01.
The operation is similar to simulation 46-01.
18
Memory reverse position
adjustment in duplex copy
(Only the AR-M201, or the
AR-M200 with the RSPF
installed)
adjustment in duplex copy
(Only the AR-M201, or the
AR-M200 with the RSPF
installed)
[Function]
When this simulation is executed, the current set correction value is displayed.
When this simulation is executed, the current set correction value is displayed.
Enter the correction value and press [START] key to save the entered correction value. (Correc-
tion value range; 1 – 99, Default: 50)
tion value range; 1 – 99, Default: 50)
For S-D mode front surface print and print of even paged in D-S mode, reverse memory copy
operation is performed from the rear edge of documents.
operation is performed from the rear edge of documents.
When, therefore, the print position adjustment of output images is required, adjust as follows:
In the reverse memory coping, when the document scan is made in the arrow direction, the out-
put image is printed from the rear edge of scan image.
put image is printed from the rear edge of scan image.
When, therefore, the print lead edge is shifted, set the reference chart so that the reference
position is on the rear edge, and use this simulation to adjust the set value so that the print lead
edge is matched.
position is on the rear edge, and use this simulation to adjust the set value so that the print lead
edge is matched.
Since printing is made from the image data most lately stored in memory to the lead edge data
from the print start position, the image lead edge adjustment is made by changing the end data
position stored in memory by the set value of this simulation.
from the print start position, the image lead edge adjustment is made by changing the end data
position stored in memory by the set value of this simulation.
Since it is performed by changing the scan end position, the image position adjustment is made
by changing the scan end position and the end data stored in memory.
by changing the scan end position and the end data stored in memory.
The adjustment modes can be selected by pressing [
] [
] key.
* The initial value of duplex setting is "1to2/Long Edge" for the duplex model, or "2to1" for the
simplex model.
∗ When paper is discharged, the shifter is operated.
[Operation]
The operation is similar to simulation 46-01.
The operation is similar to simulation 46-01.
Main
code
code
Sub
code
Contents
Details of function/operation
Mode
Initial value
of duplex
setting
Display item
(AR-M200/
M201)
LED
(AR-M200/
M201)
Display lamp
(AR-203E/
5420)
Default
Platen document scan
S-S
OC
COPY mode
lamp
lamp
AE mode
lamp
lamp
50
SPF document front
scan
scan
S-S
SPF
PRINT mode
lamp
lamp
TEXT mode
lamp
lamp
50
RSPF document back
scan (AR-M200/M201)
scan (AR-M200/M201)
D-S
RSPF
SCAN mode
lamp
lamp
—
50
Mode
Initial value of
duplex setting
duplex setting
Display item
LED
Default
OC memory reverse
output position
(AR-M201 only)
output position
(AR-M201 only)
S-D
OC
COPY mode
lamp
lamp
50
SPF/RSPF memory
reverse output position
reverse output position
D-S
SPF
PRINT mode
lamp
lamp
50
Document transport direction
Document transport direction
Scan lead edge
Print lead edge
Lead edge void (1)
Print start position
Lead edge void (1)
Print start position
Scan end position
(Default: Scan cut by void (1))
(Default: Scan cut by void (1))
Rear edge void
Print rear edge
Print rear edge
Scan direction
Scan rear edge
AR-203E/5420/M200/M201 SIMULATION, TROUBLE CODES 10 - 30
50
19
Duplex copy rear edge void
adjustment
(AR-M201 only)
adjustment
(AR-M201 only)
[Function]
Used to adjust the rear edge void amount in duplex copy.
Used to adjust the rear edge void amount in duplex copy.
When this simulation is executed, the current set value is displayed in 2 digits. (Center value:
50.) The adjustment modes can be selected by pressing [
50.) The adjustment modes can be selected by pressing [
] [
] key. (Adjustment range; 1 –
99)
Enter the adjustment value and press [START] key to save the set value and make a copy. (The
paper information is cleared for every copy.)
paper information is cleared for every copy.)
When the set value is increased by 1, the void amount is increased by about 0.1mm.
* The initial value for duplex setting is "1to2/Short Edge" for the OC setting, or "2to2" for the
RSPF setting.
∗ When paper is discharged, the shifter is operated.
[Operation]
The operation is similar to simulation 46-01.
The operation is similar to simulation 46-01.
51
02
Resist quantity adjustment
[Function]
Used to adjust the contact pressure of the main unit resist roller and the SPF/RSPF resist roller
onto paper. When this simulation is executed, the current set value is displayed.
Used to adjust the contact pressure of the main unit resist roller and the SPF/RSPF resist roller
onto paper. When this simulation is executed, the current set value is displayed.
The adjustment modes can be selected by pressing [Exposure mode selector] key (or [
]
[
] key for the AR-M200/M201).
Enter the adjustment value with [ ] [ ] key (or [Numeric] key for the AR-M200/M201) and
press [START] key to save the set value and make a copy.
press [START] key to save the set value and make a copy.
(*): Support for the installation models. For non-installation models, skip.
[Operation] (AR-M200/M201)
The operation is similar to simulation 46-01.
The operation is similar to simulation 46-01.
Main
code
code
Sub
code
Contents
Details of function/operation
Mode
Display item
LED
Default
Paper rear edge void amount
DEN-B
PRINT mode lamp
50
Print start position (Duplex back surface)
RRC-D
SCAN mode lamp
50
Mode
Display item
(AR-M200/M201)
LED
(AR-M200/M201)
Display lamp
(AR-203E/5420)
Default
Main cassette
paper feed
paper feed
TRAY1
COPY mode lamp
Main cassette lamp
Main cassette lamp
AE mode lamp
Main cassette lamp
Main cassette lamp
50
(*) 2nd cassette
paper feed
paper feed
TRAY2
COPY mode lamp
2nd cassette lamp
2nd cassette lamp
AE mode lamp
2nd cassette lamp
2nd cassette lamp
50
Manual paper feed
MFT
COPY mode lamp
Manual paper feed
lamp
Manual paper feed
lamp
AE mode lamp
Manual paper feed lamp
Manual paper feed lamp
50
RSPF document
paper feed
(Front surface)
(AR-M200/M201)
paper feed
(Front surface)
(AR-M200/M201)
SIDE1
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
Main cassette lamp
PRINT mode lamp
SCAN mode lamp
Main cassette lamp
—
50
RSPF document
paper feed
(Back surface)
(AR-M200/M201)
paper feed
(Back surface)
(AR-M200/M201)
SIDE2
COPY mode lamp
PRINT mode lamp
Main cassette lamp
PRINT mode lamp
Main cassette lamp
—
50
(*) Duplex back
surface
(AR-M201 only)
surface
(AR-M201 only)
DUP-2
PRINT mode lamp
SCAN mode lamp
Main cassette lamp
SCAN mode lamp
Main cassette lamp
TEXT mode lamp
PHOTO mode lamp
Main cassette lamp
PHOTO mode lamp
Main cassette lamp
50
AR-203E/5420/M200/M201 SIMULATION, TROUBLE CODES 10 - 31
53
08
SPF/RSPF scan position
automatic adjustment (Only
the AR-203E/M200/M201
with the SPF/RSPF
installed)
automatic adjustment (Only
the AR-203E/M200/M201
with the SPF/RSPF
installed)
[Function]
Place a A4 paper (white chart) so that it covers the SPF/RSPF scan glass and the OC glass
together, and close the SPF/RSPF.
Place a A4 paper (white chart) so that it covers the SPF/RSPF scan glass and the OC glass
together, and close the SPF/RSPF.
When this simulation is executed, the current adjustment value is displayed as the initial display.
* Default is 1. Adjustment range is 1 – 99. Adjustment unit 1 = about 0.127mm
* If the values are kept as the default values, SPF/RSPF scan is not performed properly. The
front area of the proper scan position may be scanned.
In case of AUTO, press [START] key, and the mirror unit scans from the home position to the
SPF/RSPF scan position with the adjustment value displayed. The SPF/RSPF glass cover edge
position is calculated from the difference between the SPF/RSPF glass cover edge and the OC
side document glass CCD output level. If the adjustment is normal, the adjusted value is dis-
played. If abnormal, the error LED lights up with the current set value displayed.
SPF/RSPF scan position with the adjustment value displayed. The SPF/RSPF glass cover edge
position is calculated from the difference between the SPF/RSPF glass cover edge and the OC
side document glass CCD output level. If the adjustment is normal, the adjusted value is dis-
played. If abnormal, the error LED lights up with the current set value displayed.
During the error LED is lighted, when [START] key is pressed again, execution is performed
again.
again.
[Operation]
The operation is similar to simulation 46-01. (In MANUAL)
The operation is similar to simulation 46-01. (In MANUAL)
OK/ERR display in AUTO
61
03
Polygon motor check
(HSYNC output check)
(HSYNC output check)
[Function]
When [OK]/[ENTER]/[START] key is pressed, HSYNC is performed and the polygon motor is
rotated for 30sec.
When [OK]/[ENTER]/[START] key is pressed, HSYNC is performed and the polygon motor is
rotated for 30sec.
At that time, the ZOOM lamp (or the COPY mode lamp for the AR-M200/M201) is lighted for
100msec every time when HSYNC is detected.
100msec every time when HSYNC is detected.
[Operation] (AR-M200/M201)
63
01
Shading check
[Function]
Used to display the detection level of white plate for shading.
Used to display the detection level of white plate for shading.
When [OK]/[ENTER]/[START] key is pressed, the mirror base unit moves to the white plate for
shading and the copy lamp is lighted.
shading and the copy lamp is lighted.
When the light quantity is stabilized, revision is made for every second, and the level of one
pixel at the center of CCD which is not corrected is detected and the value is displayed in deci-
mal values on the LCD/display. (3 digits)
pixel at the center of CCD which is not corrected is detected and the value is displayed in deci-
mal values on the LCD/display. (3 digits)
[Operation] (AR-M200/M201)
Main
code
code
Sub
code
Contents
Details of function/operation
Mode
Display item
(AR-M200/M201)
LED
(AR-M200/M201)
Display lamp
(AR-203E)
Default
SPF/RSPF scan position
auto adjustment
auto adjustment
AUTO
COPY mode lamp AE mode lamp
1
SPF/RSPF scan position
manual adjustment
manual adjustment
MANU
PRINT mode lamp TEXT mode lamp
1
<When OK>
<When ERR>
53-08 SPF AUTO
AUTO 100% ** OK
53-08 SPF AUTO
AUTO 100% ** ERR
1) Initial display
61-03 LSU CHK
EXECUTING...
1) Initial display
63-01 SHADING CHK
EXECUTING... 000
Click on the first or last page to see other AR-203 (serv.man5) service manuals if exist.