Sharp AR-203 (serv.man5) Service Manual ▷ View online
AR-203E/5420/M200/M201 SIMULATION, TROUBLE CODES 10 - 8
10
Toner motor aging
[Function]
When [OK]/[ENTER]/[START] key is pressed, the toner motor is rotated for 30sec.
After completion of this process, the machine goes into the main code entry standby mode.
When [OK]/[ENTER]/[START] key is pressed, the toner motor is rotated for 30sec.
After completion of this process, the machine goes into the main code entry standby mode.
[Operation] (AR-M200/M201)
14
Cancel of troubles other than
U2
U2
[Function]
Used to cancel troubles other than U2.
∗ Cancel troubles such as H trouble which writes data into EEPROM, and perform hardware
Used to cancel troubles other than U2.
∗ Cancel troubles such as H trouble which writes data into EEPROM, and perform hardware
reset.
[Operation] (AR-M200/M201)
16
Cancel of U2 trouble
[Function]
Used to cancel U2 trouble.
When [OK]/[ENTER]/[START] key is pressed, check sum of the total counter in the EEPROM is
rewritten and hardware reset is made.
Used to cancel U2 trouble.
When [OK]/[ENTER]/[START] key is pressed, check sum of the total counter in the EEPROM is
rewritten and hardware reset is made.
[Operation] (AR-M200/M201)
20
01
Maintenance counter clear
[Function]
When [OK]/[ENTER]/[START] key is pressed, the maintenance count value is cleared and
"000,000" is displayed.
When [OK]/[ENTER]/[START] key is pressed, the maintenance count value is cleared and
"000,000" is displayed.
[Operation]
21
01
Maintenance cycle setting
[Function]
The currently set code of the maintenance cycle is displayed, and the newly set data are saved.
Enter the code number with [ ] [
The currently set code of the maintenance cycle is displayed, and the newly set data are saved.
Enter the code number with [ ] [
] key (or [Numeric] key or [
] [
] key for the AR-M200/
M201) and press [START] key. The entered value is saved and the display returns to the sub
code input standby state.
code input standby state.
[Operation] (AR-M200/M201)
Main
code
code
Sub
code
Contents
Details of function/operation
1) Initial display
10-00 TONER MOTOR
EXECUTING...
1) Initial display
14-00 TRBL CANC.
CLEARED
1) Initial display
16-00 U2 TRBL CANC.
CLEARED
AR-M200/M201
1) Initial display
1) Initial display
AR-203E/5420
The count value is displayed in 3 digits X 2
times repeatedly.
times repeatedly.
<Display example: 012,345>
20-01 M-CNT CLR.
CLEARED 000,000
012
→ Blank → 345 → Blank → 012
0.7s
0.3s
0.7s
1.0s
0.7s
Code number
Setting
Remark
0
3,000 sheets
1
6,000 sheets
2
9,000 sheets
3
13,000 sheets
4
25,000 sheets
Default
5
Free (999,999 sheets)
1) The current set value is
displayed.
2) [
] key or [Numeric] key
2) [
] key or [Numeric] key
3) [OK]/[ENTER]/[START]
key
21-01 M-CYCLE
4:25,000 ( 0-5 )
21-01 M-CYCLE
5:FREE ( 0-5 )
21-01 M-CYCLE
3:13,000 ( 0-5 )
21-01 M-CYCLE
5:FREE ( 0-5 )
AR-203E/5420/M200/M201 SIMULATION, TROUBLE CODES 10 - 9
22
01
Maintenance counter display
[Function]
When [OK]/[ENTER]/[START] key is pressed, the maintenance counter is displayed.
When [OK]/[ENTER]/[START] key is pressed, the maintenance counter is displayed.
[Operation]
02
Maintenance preset display
[Function]
When [OK]/[ENTER]/[START] key is pressed, the preset value (25,000 sheets, etc.) corre-
sponding to the code set with simulation 21-01 is displayed.
When [OK]/[ENTER]/[START] key is pressed, the preset value (25,000 sheets, etc.) corre-
sponding to the code set with simulation 21-01 is displayed.
[Operation]
04
JAM total counter display
[Function]
The JAM total counter is displayed.
The JAM total counter is displayed.
[Operation]
05
Total counter display
[Function]
The total counter value is displayed.
The total counter value is displayed.
[Operation]
06
Developer counter display
[Function]
When [OK]/[ENTER]/[START] key is pressed, the developer counter value is obtained and dis-
played.
When [OK]/[ENTER]/[START] key is pressed, the developer counter value is obtained and dis-
played.
[Operation]
08
SPF/RSPF counter display
(Only the AR-203E/M200/
M201 with the SPF/RSPF
installed)
(Only the AR-203E/M200/
M201 with the SPF/RSPF
installed)
[Function]
The SPF/RSPF counter is displayed.
The SPF/RSPF counter is displayed.
[Operation]
11
FAX-related counter display
(Executable only when the
FAX is installed.)
(Executable only when the
FAX is installed.)
[Function]
The FAX-related counter is displayed.
The FAX-related counter is displayed.
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
AR-M200/M201
1) Initial display
AR-203E/5420
The operation is similar to simulation 20-01.
22-01 M-CNT
***,***
AR-M200/M201
1) Initial display
AR-203E/5420
The operation is similar to simulation 20-01.
22-02 M-CNT PRESET
***,***
AR-M200/M201
1) Initial display
AR-203E/5420
The operation is similar to simulation 20-01.
22-04 JAM TTL CNT
***,***
AR-M200/M201
1) Initial display
AR-203E/5420
The operation is similar to simulation 20-01.
22-05 TTL CNT
***,***
AR-M200/M201
1) Initial display
AR-203E/5420
The operation is similar to simulation 20-01.
22-06 DVLP CNT
***,***
AR-M200/M201
1) Initial display
AR-203E
The operation is similar to simulation 20-01.
22-08 SPF CNT
***,***
1) Initial display
∗ [Clear] key: FAX control is terminated.
2) Select 1
2) Select 1
("xxx,xxx" is the current value.)
∗ [Clear] key: Returns to "1) Initial display".
∗ [Clear] key: Returns to "1) Initial display".
2) Select 2
("xxxxx: xx. xx" is the current value.)
∗ [Clear] key: Returns to "1) Initial display".
∗ [Clear] key: Returns to "1) Initial display".
SELECT COUNTER
1:PAGE 2:TIME
SEND PAGE:xxx,xxx
RECV PAGE:xxx,xxx
TX TIME:xxxxx:xx.xx
RX TIME:xxxxx:xx.xx
AR-203E/5420/M200/M201 SIMULATION, TROUBLE CODES 10 - 10
22
12
Drum counter display
[Function]
The drum counter is displayed.
The drum counter is displayed.
[Operation]
13
CRUM type display
[Function]
The CRUM type currently set (written) in the CRUM chip is displayed.
The CRUM type currently set (written) in the CRUM chip is displayed.
[Operation] (AR-M200/M201)
14
ROM version display
[Function]
The P-ROM version is displayed.
Press [ ] [ ] key (or [Numeric] key or [
The P-ROM version is displayed.
Press [ ] [ ] key (or [Numeric] key or [
] [
] key for the AR-M200/M201) to switch the dis-
play version.
[Operation]
16
Duplex counter display
(AR-M201 only)
(AR-M201 only)
[Function]
The duplex counter is displayed.
The duplex counter is displayed.
[Operation]
17
Copy counter display
[Function]
The copy counter is displayed.
The copy counter is displayed.
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
AR-M200/M201
1) Initial display
AR-203E/5420
The operation is similar to simulation 20-01.
22-12 DRUM CNT
***,***
Code number
CRUM type
Display item
00
Not set
0
01
BTA-A
BTA-A
02
BTA-B
BTA-B
03
BTA-C
BTA-C
99
Conversion
CONVERSION
1) The CRUM type is displayed.
22-13 CRUM TYPE
01:BTA-A
Code number
Version
Display item
0
Main unit Program
MAIN PROG.
1
F-IMC Program
F-IMC PROG.
2
LCD DATA
LCD DATA
AR-M200/M201
1) Initial display
2) [Numeric] key or [
] key
2) [Numeric] key or [
] key
AR-203E/5420
The operation is similar to simulation 20-01.
22-14 ROM VER.
MAIN PROG. 00.00
22-14 ROM VER.
F-IMC PROG. 00.00
22-14 ROM VER.
LCD DATA 00.00
1) Initial display
22-16 DPLX CNT
***,***
AR-M200/M201
1) Initial display
AR-203E/5420
The operation is similar to simulation 20-01.
22-17 COPIES CNT
***,***
AR-203E/5420/M200/M201 SIMULATION, TROUBLE CODES 10 - 11
22
18
Printer counter display
[Function]
The printer counter is displayed.
The printer counter is displayed.
[Operation]
19
Scanner mode counter
display
(AR-203E/M200/M201)
display
(AR-203E/M200/M201)
[Function]
The scanner mode counter is displayed.
The scanner mode counter is displayed.
[Operation]
21
Scanner counter display
[Function]
The scanner counter is displayed.
The scanner counter is displayed.
[Operation]
22
SPF/RSPF JAM counter
display (Only the AR-203E/
M200/M201 with the
SPF/RSPF installed)
display (Only the AR-203E/
M200/M201 with the
SPF/RSPF installed)
[Function]
The SPF/RSPF JAM counter is displayed.
The SPF/RSPF JAM counter is displayed.
[Operation]
24
01
JAM total counter clear
[Function]
When [OK]/[ENTER]/[START] key is pressed, the JAM total counter is cleared to 0 and
"000,000" is displayed on the LCD/display.
When [OK]/[ENTER]/[START] key is pressed, the JAM total counter is cleared to 0 and
"000,000" is displayed on the LCD/display.
[Operation]
04
SPF/RSPF counter clear
(Only the AR-203E/M200/
M201 with the SPF/RSPF
installed)
(Only the AR-203E/M200/
M201 with the SPF/RSPF
installed)
[Function]
When [OK]/[ENTER]/[START] key is pressed, the SPF/RSPF counter value is cleared to 0 and
"000,000" is displayed on the LCD/display.
When [OK]/[ENTER]/[START] key is pressed, the SPF/RSPF counter value is cleared to 0 and
"000,000" is displayed on the LCD/display.
[Operation]
05
Duplex counter clear
(AR-M201 only)
(AR-M201 only)
[Function]
When [OK]/[ENTER]/[START] key is pressed, the duplex counter value is cleared to 0, and
"000,000" is displayed on the LCD/display.
When [OK]/[ENTER]/[START] key is pressed, the duplex counter value is cleared to 0, and
"000,000" is displayed on the LCD/display.
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
AR-M200/M201
1) Initial display
AR-203E/5420
The operation is similar to simulation 20-01.
22-18 PRT.CNT
***,***
AR-M200/M201
1) Initial display
AR-203E
The operation is similar to simulation 20-01.
22-19 S-MODE CNT
***,***
AR-M200/M201
1) Initial display
AR-203E/5420
The operation is similar to simulation 20-01.
22-21 SCAN CNT
***,***
AR-M200/M201
1) Initial display
AR-203E
The operation is similar to simulation 20-01.
22-22 S JAM CNT
***,***
AR-M200/M201
1) Initial display
AR-203E/5420
The operation is similar to simulation 20-01.
24-01 JAM TTL CLR.
CLEARED 000,000
AR-M200/M201
1) Initial display
AR-203E
The operation is similar to simulation 20-01.
24-04 SPF CLR.
CLEARED 000,000
1) Initial display
24-05 DPLX CLR.
CLEARED 000,000
Click on the first or last page to see other AR-203 (serv.man5) service manuals if exist.