DOWNLOAD Sharp AR-203 (serv.man5) Service Manual ↓ Size: 14.96 MB | Pages: 127 in PDF or view online for FREE

AR-203E/5420/M200/M201  SIMULATION, TROUBLE CODES  10 - 4

02

02

SPF/RSPF sensor status 
display (Only the AR-203E/
M200/M201 with the 
SPF/RSPF installed)

[Function]
The ON/OFF status of the SPF/RSPF sensors can be checked with the LCD/LED.
When a sensor is ON, the sensor name is displayed on the LCD/LED.

03

SPF/RSPF Motor ON 
(Only the AR-203E/M200/
M201 with the SPF/RSPF 
installed)

[Function]
When [OK]/[ENTER]/[START] key is pressed, the motor rotates for 10sec at the speed corre-
sponding to the set magnification ratio.

[Operation] (AR-M200/M201)
The operation is similar to simulation 01-01.

06

Resist clutch ON (SPF) 
(AR-203E only)

When the [START] key is pressed, the SPF resist clutch (SRRC) repeats ON (500 ms) and OFF 
(500 ms) 20 times.

08

RSPF paper feed solenoid 
operation check 
(Only the AR-M200/M201 
with the RSPF installed)

[Function]
The RSPF paper feed solenoid (SPUS) repeats ON for 500ms and OFF for 500ms 20 times by
the use of the solenoid drive control Bios.

09

RSPF reverse solenoid 
operation check 
(Only the AR-M200/M201 
with the RSPF installed)

[Function]
The RSPF reverse solenoid (SPFS) repeats ON for 500ms and OFF for 500ms 20 times by the
use of the solenoid drive control Bios.

03

03

Shifter operation check 
(AR-M200/M201)

[Function]
The shifter is moved back and forth in four reciprocations.

Main 
code

Sub 

code

Contents

Details of function/operation

Sensor

Display item

(AR-M200/M201)

Display item

(AR-203E)

Document set sensor

SPID  

TD cartridge replacement required 
lamp

RSPF document transport sensor

SPPD  

Misfeed lamp

RSPF paper feed cover open/close 
sensor

SDSW  

—

RSPF paper exit sensor

SPOD  

—

1) Initial display

2) When the sensor is ON:

02-02 SPF SENSOR

02-02 SPF SENSOR

SPID SPPD SDSW SPOD

1) Initial display

02-08 SPF SPUS CHK

EXECUTING...

1) Initial display

02-09 RSPF SPFS CHK

EXECUTING...

1) Initial display

03-03 SHIFTER CHK

EXECUTING...

AR-203E/5420/M200/M201  SIMULATION, TROUBLE CODES  10 - 5

05

01

Operation panel display 
check

[Function]
<LED check mode (All ON/Individual ON)>
When [OK]/[ENTER]/[START] key is pressed, all the LCD's on the operation panel are turned
ON (all pixels ON).
After 5sec of ON, the machine goes into the sub code entry standby mode.
When [Mode Select] key is pressed under the all ON state, the mode is shifted to the individual
ON mode, where the LED's are turned on one by one from the left upper end to the left lower
side then from the right upper side to the right lower side. (All the pixels of LCD are lighted
simultaneously.) After lighting all the LCD's sequentially, all the LCD's are lighted simulta-
neously. After 5sec from lighting all the LCD's simultaneously, the machine goes into the sub
code entry standby mode. (Cycle of individual ON mode: ON 300ms, OFF 20ms)

When [Clear] key is pressed in the LED check mode, the machine goes into the sub code entry
standby mode.
When [START] key is pressed, the machine goes into the key input check mode.

<Key input check mode>
When the machine goes into the key input check mode, the value display section indicates "– –
–" (For the AR-M200/M201, 0 of the LCD is indicated).
When any key is pressed after pressing a key on the operation panel, "+1" is added to the
value.
Once a key is pressed, it is not recounted.
When [START] key is pressed, counting is made and the machine goes into the LED ON check
mode (LED all ON status) after 3sec.
When [Clear] key is pressed for the first time, it is counted. When it is pressed for the second
time, the key check mode is retained as well as when another key is pressed.

(Note in the key input check mode)
• Be sure to press [START] key at the last. (If it is pressed on the way, the machine goes into

the LED ON check mode.) (LED all ON status)

• Multi key input is ignored.

[Operation] (AR-M200/M201)
<LED check mode (All ON/Individual ON)>

<Key input check mode>

02

Fusing lamp, cooling fan 
operation check

[Function]
When [OK]/[ENTER]/[START] key is pressed, the fusing lamp repeats ON for 500ms and OFF
for 500ms 5 times. During this period, the cooling fan motor rotates.

Note: 
When the CE mark setting is ON, the slow start function may operate depending on the
employed frequency. If the state of the heater lamp cannot be checked, temporarily set SIM 26-
30 to "0" and check the lamp state.  After confirming that the heater lamp is ON, set SIM 26-30
to "1" again.

03

Copy lamp ON

[Function]
When [OK]/[ENTER]/[START] key is pressed, the copy lamp turns ON for 5sec.

Main 
code

Sub 

code

Contents

Details of function/operation

1) Initial 

display

2) When [Mode Select] key is pressed, the machine goes into the individual ON mode.

■■■■■■■■■■■■■■■■■■■■■
■■■■■■■■■■■■■■■■■■■■■

1) Initial display

2) [OK]/[ENTER]/[START]

key

05-01 LCD/LED CHK.

                     0

05-01 LCD/LED CHK.

                    **

1) Initial display

05-02 HT LAMP CHK

EXECUTING...

1) Initial display

05-03 C-LAMP CHK

EXECUTING...

AR-203E/5420/M200/M201  SIMULATION, TROUBLE CODES  10 - 6

06

01

Paper feed solenoid ON

[Function]
When [OK]/[ENTER]/[START] key is pressed, the selected paper feed solenoid repeats ON for
500ms and OF for 500ms 20 times.
When tray select key (or [Numeric] key or [

] [

] key for the AR-M200/M201)

 

is pressed,

the paper feed solenoid setting is switched.

02

Resist solenoid ON

[Function]
When [OK]/[ENTER]/[START] key is pressed, the resist solenoid repeats ON for 500ms and
OFF for 500ms 20 times.

07

01

Warm-up display and aging 
with jam

[Function]
Copying is repeated to make the set quantity of copies.
When the simulation is executed, warm-up is started and warm-up time is added for every sec-
ond from 0 and displayed.
When warm-up is completed, addition is stopped. When [Clear All] key is pressed, the ready
lamp lights up.
After that, enter the copy quantity with [ ] [ ] key

 

(or [Numeric] key for the AR-M200/M201)

and press [OK]/[ENTER]/[START] key to repeat copying of the set quantity (interval 0sec).
To cancel the simulation, turn off the power or execute a simulation which causes hardware
reset.

06

Intermittent aging

[Function]
Copying is repeated to make the set quantity of copies.
When the simulation is executed, warm-up is performed and the ready lamp is lighted.
Enter the copy quantity with the [ ] [ ] key

 

(or [Numeric] key for the AR-M200/M201) and

press [OK]/[ENTER]/[START] key, and copying is executed to make the set quantity of copies,
and the ready state is kept for 3sec, and copying is executed again to make the set quantity of
copies. These operations are repeated.
To cancel the simulation, turn off the power or execute a simulation which executes hardware reset.

08

Shift to copy with the 
warm-up display

[Function]
Enter the simulation code, and warm-up is started and warm-up time is counted for every sec-
ond from 0 and displayed.
When [Clear All] key is pressed during counting up, "0" is displayed on the display and counting
is stopped. However, warm-up is continued.
After completion of warm-up, counting is terminated. (The aging function is removed from simu-
lation 07-01.)

Main 
code

Sub 

code

Contents

Details of function/operation

Code number

Setting

Remark

0

CPFS1

1

CPFS2

Operation is possible only when No. 2 cassette is installed. 

2

MPFS

1) Initial display

2) [Numeric] key or [

] key

2) [Numeric] key or [

] key

3) [OK]/[ENTER]/[START]

key

4) Returns to the initial 

display.

06-01 PSOL CHK

0:CPFS1

06-01 PSOL CHK

1:CPFS2

06-01 PSOL CHK

2:MPFS

06-01 PSOL CHK

EXECUTING...

1) Initial display

06-02 RES.R SOL CHK

EXECUTING...

1) Initial display

2) After 10sec

07-01 W-UP/AGING

                    0

07-01 W-UP/AGING

                   10

1) Initial display (Basic display of copy)

READY TO COPY

  100%    A4     0

1) Initial display

2) After 10sec

07-08 W-UP C-MODE

                    0

07-08 W-UP C-MODE

                    10

AR-203E/5420/M200/M201  SIMULATION, TROUBLE CODES  10 - 7

08

01

Developing bias

[Function]
When [OK]/[ENTER]/[START] key is pressed, the developing bias signal is turned ON for 30sec.

When, however, an actual output value is measured, use simulation 25-01.

After completion of this process, the machine goes into the sub code entry standby mode.

02

Main charger (Grid high)

[Function]
When [OK]/[ENTER]/[START] key is pressed, the main charger is outputted for 30sec in the grid
voltage HIGH move.

After completion of this process, the machine goes into the sub code entry standby mode. 

03

Grid voltage (Low)

[Function]
When [OK]/[ENTER]/[START] key is pressed, the main charger is outputted for 30sec in the grid
voltage LOW move.

After completion of this process, the machine goes into the sub code entry standby mode.

06

Transfer charger

[Function]
When [OK]/[ENTER]/[START] key is pressed, the transfer charger is outputted for 30sec.

After completion of this process, the machine goes into the sub code entry standby mode.

09

01

Duplex motor normal 
rotation operation check 
(AR-M201 only)

[Function]
Use the duplex motor Bios to drive the duplex motor in the normal direction (paper exit direc-
tion) for 30sec.

After completion of this process, the machine goes into the sub code entry standby mode.

02

Duplex motor reverse 
operation check 
(AR-M201 only)

[Function]
Use the duplex motor Bios to drive the duplex motor in the reverse direction for 30sec.

After completion of this process, the machine goes into the sub code entry standby mode.

04

Duplex motor rotation speed 
adjustment (AR-M201 only)

[Function]
When this simulation is executed, the currently set value is displayed.
Enter the adjustment value with [Numeric] key and press [OK]/[ENTER]/[START] key. The
entered value is stored and the machine goes into the sub code entry standby mode. The
greater the set value is, the higher the speed is. The smaller the set value is, the lower the
speed is. (Setting range: 1 - 13, Default: 8)

Main 
code

Sub 

code

Contents

Details of function/operation

1) Initial display

08-01 DVLP BIAS SET.

EXECUTING...

1) Initial display

08-02 MHV(H) SET.

EXECUTING...

1) Initial display

08-03 MHV(L) SET.

EXECUTING...

1) Initial display

08-06 THV SET.

EXECUTING...

1) Initial display

09-01 DPLX ROT.

EXECUTING...

1) Initial display

09-02 DPLX ROT.REV.

EXECUTING...

1) Initial display

2) [Numeric] key

3) [OK]/[ENTER]/[START]

key

09-04 DPLX ROT.SPEED

            8( 1-13)

09-04 DPLX ROT.SPEED

            7( 1-13)

09-04 DPLX ROT.SPEED

            7( 1-13)