Sharp LL-P202V (serv.man2) Service Manual ▷ View online
LL-P202V/S242A INSTALLATON / SETTINGS 2 - 25
■
Other functions
In Windows 8, input panel functions can be used.
In Windows 7, touch pointer and input panel functions can be
used.
For information about the touch pointer and input panel functions,
see Windows Help.
Touch pointer：
A translucent image of a mouse appears near the point touched.
The left/right buttons of the image can be clicked to perform the
same actions as left/right clicking a mouse.
Input panel：
A software keyboard and an input panel with handwriting
recognition appear on the screen.
Windows 8 and Windows 7（excluding starter）, the ink function of
Microsoft Office can be used.
Handwritten comments can be written, and hand writing can be
recognized.
For details, see Microsoft Office Help.
■Cautionary points
• When performing touch actions, use the ball of your finger.
• When performing pen actions, use the supplied touch pen.
• Do not use the touch pen for any purpose other than touch panel
operation.
• Do not press hard on the tip of the touch pen.
• If there is dirty or foreign matter on the tip of the touch pen,
remove it. Failure to do so may damage the screen.
• Even when in pen only mode, the monitor may respond to
objects other the included touch pen.
LL-P202V/S242A INSTALLATON / SETTINGS 2 - 26
7. DIGITIZER PEN
The LL-P202V monitor supports a digitizer pen. To use the digitizer pen, the utility software must be installed.
7-1. Digitizer pen actions
- Function button 1: Pressing and holding this button and touching the screen performs the same action as a right-click on a mouse.
(factory default)
- Function button 2: Pressing and holding this button while moving the pen on the screen enables the eraser function. (factory default)
You can change the functions that are assigned to the function buttons using the digitizer pen utility.
Hover operations
The unit will recognize when the tip of the pen is hovering within 15 mm of the screen, allowing you to position the pointer without touching
the screen.
Shortcut launcher
When you press function button 1 while in the hovering state, a circular shortcut launcher menu will appear.
You can select the desired operation from the menu. The shortcut launcher disappears when you select a function or press function button
1 again.
You can press [Launch registered app] to register an application and its name. Once registered, [Launch registered app] is changed to the
name of the registered application, allowing the application to be launched from the shortcut launcher.
(MEMO)
-
The shortcut launcher is not displayed on the Windows 8.1/8 Start screen or on the Windows Store screen.
-
When the digitizer pen is connected, digitizer pen actions are enabled and touch pen actions are disabled. To use touch pen actions,
disconnect the digitizer pen.
-
The digitizer pen supports pen pressure functions. The pen can be used with software that responds to pen pressure.
-
If the digitizer pen does not operate correctly, try placing the tip of the pen vertically on the screen.
LL-P202V/S242A INSTALLATON / SETTINGS 2 - 27
7-2. Digitizer pen stand
Place the digitizer pen in the pen stand when it is not being used.
You can wrap the digitizer pen cable around the digitizer pen stand.
Close the top cover and bottom cover as shown in the following diagram.
7-3. Spare pen tip storage
The pen stand features a pen tip storage area where you can store spare pen tips.
(MEMO)
-
Spare pen tips are not stored in the stand at the time of purchase. Store the spare pen tips in the pen stand to make sure you do not lose
them.
1) Remove the spare pen tip storage cap.
LL-P202V/S242A INSTALLATON / SETTINGS 2 - 28
2) Insert the spare pen tips into the holes in the pen tip storage.
3) Reattach the cap.
7-4. Replacing the digitizer pen tip
Replace the pen tip when it is worn or damaged. Using the digitizer pen with a worn or damaged pen tip may scratch the surface of the
monitor, or may cause the digitizer pen function to stop operating. Pen tips will wear with normal use.
1) Unscrew the pen tip cover and remove it.
2) Pull out the pen tip.
3) Insert a new pen tip, and reattach the pen tip cover.
Click on the first or last page to see other LL-P202V (serv.man2) service manuals if exist.