DOWNLOAD Sharp UP-X500 (serv.man4) Service Manual ↓ Size: 1.38 MB | Pages: 75 in PDF or view online for FREE

UP-X500U

DIagnostics Specifications

4 – 22

*

Since this test is an object for debugging, it is not used by the service manual.

Use the MCR test card (R/O) to execute the test.
The MCR test card is read and verified to check. 
There are two patterns of read data:

In data read, the parity bit of each character is checked. The LRC code
is also checked.
Test operations (One cycle of test)

The test is performed using the MCR test card (R/O)
Verify checks are performed by reading the MCR test card.
There are three types of data patterns that can be read.

When data is read, the parity bit of each character is checked. In

addition, the LRC code is also checked.

*

Since this test is an object for debugging, it is not used by the service
manual.

The MCR test card (W/R) is used to execute the test.
The JBA data are written into the MCR card, and then the verify check
is executed.
There are following two write patterns:

When writing data, a parity bit is added to each character. The LRC
code is also calculated and added. 
When reading data, the parity bit of each character is checked. The
LRC code is also checked. 
Test operations (One cycle of test)
Data pattern 1 write

4

Data pattern 1 read/verify. Data pattern 1 test result is displayed. 

4

Data pattern 2 write

4

Data pattern 2 read/verify. Data pattern 1 test result is displayed. 

In the write test, "Write" is highlighted. When the card is passed and
write is completed, "Read" is highlighted and the mode is shifted to the
card read wait state. 
When reading is completed, data are checked and the result is dis-
played. 

Similar to the previous test (2). However, read data are not checked.  

The error information of the above (1) - (3) recorded in the DRAM is displayed.
If there is no error, "OK" or "NO ERROR" is displayed. 

On the above menu, use [

2

] and [

4

] keys to select a test item. Press

[ENTER] key to execute the test. When [ESC] key is pressed, the

display returns to the initial menu. 

*

Since this test is an object for debugging, it is not used by the service
manual.

By the card operation, the test is executed and each information is displayed.

When [ESC] key is pressed, the display returns to the menu display.

The test is performed by inserting the card and the information is displayed.
You can return to the menu screen by pressing the [ESC] key.

JBA data pattern : Same as the JBA data pattern of (1)

ABA data pattern :  "1234567890123456789012345678901234567"

(37 characters)

JBA pattern read/verify

: The test result is displayed.

ABA data pattern read/verify

: The test result is displayed. 

IATA data pattern:

"SHARP TEST CARD 0123456789ABCD~XYZ

0123456789 UKOG-6718RCZZ"(76 characters)

ABA data pattern 1: "0123456789012345678901234567"

 (28 characters)

ABA data pattern 2: "0123456789~01234567890123456789

 (100 characters)

IATA data pattern 

Read/Verify

: The test result is displayed.

ABA data pattern 1

Read/Verify

: The test result is displayed.

ABA data pattern 2

Read/Verify

: The test result is displayed.

JBA data pattern 1

: "*SHARP*TEST-CARD*ABCDE - XYZ 

1234567890123456789012" (69 characters)

JBA data pattern 2: 

: "2*SHARP*TEST-CARD*ABCDE - XYZ

123456789012345678901" (69 characters)

MCR/W Test

MCR write/read-verify Test

MCR Read Test (2 tracks)

MCR Read Test (3 tracks)

Any Card Read Test

CURSOR:Move       ENTER:Select       ESC:Exit

Error Table

MCR Read Test

Pass Count = 0000

ESC:exit.

Scan MCR-Test-Card[r/o] to read and display mcr data

(UKOG-6663RCZZ)

Track 0 data (ASCII)
Track 0 data (Binary)
Track 0  Read result

Track 1 data (ASCII)
Track 1 data (Binary)
Track 1  Read result

Data on Track 0 
Read result of track 0
Data on Track 1
Read result of track 1
Data on track 2
Read result of track 2

MCR Read Test

Pass Count = 0000

Scan MCR-Test-Card [R/O] to read and display mcr data
(UKOG-2357RCZZ)

ESC: Exit

UP-X500U

DIagnostics Specifications

4 – 23

*

Since this test is an object for debugging, it is not used by the service
manual.

When the card operations are executed for 4 times in total, the test is

terminated.
When [ESC] key is pressed, the display returns to the menu display.

By the card operation, the test is executed and each information is dis-

played.
When [ESC] key is pressed, the display returns to the menu display. 

The magnetic card conforms to JISX6301.

(1) - 1. Character to be used

7 units, even parity

(1) - 2. Character composition

(1) - 3. Character descriptions

(2) - 1. Characters to be used. 

4 units, odd parity

(2) - 2. Character composition

(2) - 3. Character descriptions

Character No.

1

2 - 70

71

72

Name

(1) Header

(2) Data

(3) Stop code

(4) LRCC

MCR/W Write Test

Write MCR (The reversal display at the time of white.)

ESC:Exit

Read MCR (The reversal display at the time of Raed.)

 

The data pattern which writes in

Read data
Read result

MCR Read Test

Pass Count = 0000

ESC:exit.

Scan and Card to read and display MCR data

Track 0 data (ASCII)
Track 0 data (Binary)
Track 0  Read result

Track 1 data (ASCII)
Track 1 data (Binary)
Track 1  Read result

b8

b7

b6

b5

b4

b3

b2

b1

Parity bit

Character bit

Card slide direction

1

 Header

: For detection of data start (SFFH)

2

 Data

: Data area

3

 Stop code

: For detection of data end (SFFH)

4

 LRC code

: Even number check code for characters No. 2 - 71

Character No.

1

2 - 28

39

40

Name

(1) Header

(2) Data

(3) Stop code

(4) LRCC

1 Header

: For detection of data start (S0BH)

2 Data

: Data area

3 Stop code

: For detection of data end (S1FH)

4 LRC code

: Even number check code for characters No. 2 - 39

Magnetic stripe
(The JBA data are recorde

(Card surface)

The emboss contents
are read. 

b5

b4

b3

b2

b1

Parity bit

Character bit

Card slide direction

Magnetic stripe
(The JBA data are
recorded in the 2nd track.)

The emboss contents
cannot be read.

(Card back surface)

UP-X500U

DIagnostics Specifications

4 – 24

Set as follows:

The even parity of each bit is calculated.

*

See the above table vertically.

Calculation is made as above. 

*

See the above table vertically.

This test is used to check the PCMCIA (2 slots).

•  UP-X500 main unit diag execution media x 1

•  SYCARD PCC test 450F (Card BUS) x 1

The test items of this test are as follows:

•  PCMCIA test (Slot Low)

•  PCMCIA test (Slot, High)

• Error table

The PCMCIA lower slot is checked. 

The PCMCIA upper slot is checked.

The error information of the above (1) ~ (2) recorded in the DRAM is dis-

played. When there is no error, "OK" or "NO ERROR" is displayed. 

On the above menu, use [

2

] and [

4

] keys to select a test item. Press

[ENTER] key to execute the test. When [ESC] key is pressed, the dis-

play returns to the initial menu. 

When [ENTER] key is pressed, the test is executed. 

The test result is displayed on the bottom of the display. 

•  When OK : TEST OK!

•  When Error: TEST ERROR!

When any key is pressed after execution of the test, the display returns
to the initial menu display.

When [ESC] key is pressed, the display returns to the initial menu display.

<JBA>

<ABA>

B7

6

5

4

3

2

1

B0

B7

6

5

4

3

2

1

B0

For 1 byte

Header code

1

1

1

1

1

1

1

1

Header code

1

1

1

1

1

1

1

1

For 2 byte
For 3 byte

|

For 37 byte
For 38 byte

For 39 byte

For 40 byte

|

For 69 byte

For 70 byte
For 71 byte

Data 1 character "1"
Data 2 character "2"

|

Data 36 character "A"
Data 37 character "B"

Data 38 character "C"

Data 39 character "D"

|

Data 68 character

Data 69 character

Stop code

1
1

0
0

1

0

1

0
0

1
1

1

1

1

1
1

0
0

0

0

1

1
1

0
0

0

0

1

0
0

0
0

0

0

1

0
0

0
0

0

1

1

0
1

0
1

1

0

1

1
0

1
0

1

0

1

Data 1 character "1"
Data 2 character "2"

|

Data 36 character "6"
Data 37 character "7"

Stop code

0
0

0
0

0

0
0

0
0

0

0
0

0
0

0

0
0

1
0

1

0
0

0
0

1

0
0

1
1

1

0
1

1
1

1

1
0

0
1

1

LRC  code

0

0

0

0

1

1

0

1

For 72 byte

LRC code

0

1

1

1

1

0

0

0

JBA - LRC code: 2 byte - 72 byte

ABA - LRC code: 2 byte - 39 byte

JBA - Each character is an even parity of bit 0 - bit 6.

ABA - Each character is an odd parity of 0 bit - 3 bit.

PCMCIA Test

PCMCIA Test Slot High)

PCMCIA Test (Slot Low)

CURSOR:Move       ENTER:Select       ESC:Exit

Error Table

PCMCIA Test

Press Enter Key

Insert PCMCIA Test Card Lower Slot

ENTER:Start                                  ESC:Exit

UP-X500U

DIagnostics Specifications

4 – 25

When [ENTER] key is pressed, the test is executed. 

The test result is displayed on the bottom of the display. 

•  When OK : TEST OK!

•  When Error: TEST ERROR!

When any key is pressed after execution of the test, the display returns to
the initial menu display.
When [ESC] key is pressed, the display returns to the initial menu display. 

The CPU information, the BIOS version, the PCP3 version, and the
shorter setting are displayed. 

•  UP-X500 main unit diag execution media   x 1

The test item of this test is as follows:

• Information display

The CPU maker name, the clock frequency, the BIOS version, the
PCP3 version, the shorter setting are displayed. 

*

The clock frequency is a measured value, and may include a slight error. 

When any key is pressed, the display returns to the menu display.

The read test of the WMF clerk key is performed.

•  UP-X500 system unit diagnostic test execution media   x 1

The following items will be checked:

Clerk test

Error table

The read data of the clerk key is displayed.

A list of error information on (1) Clerk Test recorded in DRAM is displayed.
If no error occurs, OK or NO ERROR is displayed.

With the above screen displayed, select the test item you want to execute

using [

2

] and [

4

] keys, and then press [ENTER] to execute the test.

You can return to the initial menu screen by pressing the [ESC] key.

The number of the clerk key connected to the system unit is displayed.

The display returns to the initial screen when any key is pressed.

Command response error.

Erroneous read data end code

CPU Maker  : The CPU maker name is displayed. 

BIOS Ver.

: Bios version No. is displayed. 

PCP3 Ver.

: PCP3 version No. is displayed.

Shorter

: Shorter setting is displayed by the model name

(UP-X500, RZ-A340, RZ-A340W, etc.)

CPU therm

: CPU temperature is displayed.

PCMCIA Test

Press Enter Key

Insert PCMCIA Test Card Upper Slot

ENTER:Start                                  ESC:Exit

CPU clock

CPU Maker

BIOS Ver.

PCP3 Ver.

Shorter

:

:

:

:

:

xxx Mhz

x.xx

x.xx

(CPU maker name)

(Model name)

CPU therm

: xxx c

㪚䌬䌥䌲䌫

 

䌋䌥䌹

 

䌔䌥䌳䌴

 

C

䌬䌥䌲䌫

 

䌔䌥䌳䌴

 

Error Table

CURSOR: Move          ENTER: Select             ESC: Exit

WMF Clerk Key No. Display 

CLERK KEY No.  :  XXX 

Press any Key to Exit.