DOWNLOAD Sharp UP-X300 (serv.man45) Service Manual ↓ Size: 3.62 MB | Pages: 73 in PDF or view online for FREE

UP-X300V

DIagnostics Specifications

3 – 7

Select an test item with [

2 ] and [ 4 ] keys on the above menu and press

[ENTER] key to start the test. When [ESC] key is pressed, the display

returns to the initial menu. 

The standard value of the hard disk is displayed. 

When any key is pressed, the test is terminated and the display returns

to the menu display of the previous (1).

Select an item in each position indicated with "

"

(In the above display, the item surrounded by a 

 is selected and the

value surrounded by a 

 is selected.)

When, in the above display, "Pass count" is counted up (when the test

point is counted from 000 to the final LBA, Pass count is counted up by

1) and all the error counters of all the error kinds are not counted up
(remaining at 00000), the test is OK.

During execution of the test, when [SPACE] key is pressed, the test is

interrupted. 

During interruption of the test, when [SPACE] key is pressed, the test is

resumed. 

During execution or interruption of the test, when [ESC] key is pressed,
the display returns to the menu of (1).

Select an item in each position indicated with "

"

(In the above display, the item surrounded by a 

 is selected and the

value surrounded by a 

 is selected.)

When, in the above display, "Pass count" is counted up (when the test

point is counted from 000 to the final LBA, Pass count is counted up by
1) and all the error counters of all the error kinds are not counted up

(remaining at 00000), the test is OK.

The procedures to interrupt, resume, and terminate the test are the
same as those of the above (3). 

Similar to the above (4).

Drive type

: Hard disk drive name

Capacity

: Memory capacity of the hard disk

Cylinder number

: Max. cylinder number

Head number

: Max. head number

Sector number

: Max. sector number

Lba number

: LBA number

Firmware Ver.

: Firmware version No.

Hard Disk Drive Diagnostics

READ MODE TEST

ERROR LOGGING AREA CLEAR(DIAG)

Drive status display
Sequential seek test

Random seek test

Seek & Read test

Target Sector Read test

HD Dump test

Error LOGGING Information Display (DIAG)

Disk Controller Check test

WRITE MODE TEST

Seek  &  Write/Read-Verify test

Target Sector Write/Read-Verify test

HD Patch test

ENTER:Select

ESC:Exit

     :FMove

Error Table Display

Smart ON/OFF

Drive Status display

hard disk drive information

Drive Type     

Capacity        

Cylinder number 
Head number   

Sector number  

Press any key to exit.

:

:
:
:
:

Farm ware ver   :

Target Sector Read test

LBA range 

?

Error Kinds

Drive not ready

Retry count ?

Bad controller

[Error stop continue 1 pass]

Test Start ?[ Yes  No]

Compare error

Pass count=xxxxx

Test Point=xxxxxxxx (LBA)

[0000000-194608791]

[0-4]= 0

ESC:Exit      SPACE:Stop       Start

Error details content

or

~

~

Target Sector Read test

LBA range 

?

Error Kinds

Drive not ready

Sector count ?

Bad controller

[Error stop continue 1 pass]

Test Start ?[ Yes  No]

Compare error

Pass count=xxxxx

Test Point=xxxxxxxx (LBA)

[0000000-194608791]

[0-63]= 63

Retry count  ?

[0-4]= 0

ESC:Exit      SPACE:Stop       Start

Error details content

or

~

~

UP-X300V

DIagnostics Specifications

3 – 8

Select an item in each position indicated with "

"

(In the above display, the item surrounded by a 

 is selected and the

value surrounded by a 

 is selected.)

When, in the above display, "Pass count" is counted up and all the error

counters of all the error kinds are not counted up (remaining at 00000),

the test is OK.
The procedures to interrupt, resume, and terminate the test are the

same as those of the above (3). 

Select an item in each position indicated with "

"

(In the above display, the item surrounded by a 

 is selected and the

value surrounded by a 

 is selected.)

The above display shows the contents of former 256 byte in the position
of 000 LBA sector. Press [PGDN] key to display the latter 256 byte. 

(When [PGDN] key is pressed on the above menu, the latter half of 256

byte in the position of 000 LBA sector is displayed.) Press PGDN key to
display the former 256 byte. 

When [ESC] key is pressed, the display returns to the menu display of

the previous (1).

When the pass count is counted up and "OK!" is displayed at stop, the
test is OK. (Note that it takes several seconds for 1 pass.)

When [SPACE] key is pressed during the test, the test is interrupted. 

When [SPACE] key is pressed during interruption of the test, the test is
resumed.

When [ESC] key is pressed during execution or interruption of the test,
the test is terminated and the display returns to the menu display.

The status of the smart function is displayed in the position of "*"

Press [ENTER] key to turn ON/OFF the smart function. When [ESC]
key is pressed, the display returns to the menu display of the above (1).

Refer to HDD SMART.DOC.

SMART values stored in HDD are displayed.
Legends

With the above screen displayed, select YES using the cursor keys and
then press ENTER to save the values displayed in the file.
You can exit the program without saving the values, by selecting NO
and then pressing ENTER or ESC.

Target Sector Read test

LBA range 

?

Error Kinds

Drive not ready

Sector count ?

Bad controller

[Error stop continue 1 pass]

Test Start ?[ Yes  No]

Pass count=xxxxx

Test Point=xxxxxxxx (LBA)

[0000000-194608791]

[0-63]= 63

Retry count  ?

[0-4]= 0

ESC:Exit      SPACE:Stop       Start

Error details content

or

HD Dump test

Physical address ? [CCCC.HH.SS]= 0000 .  00 . 01

The first half sector

 0 0 0 :HH HH     HH HH-|HH HH   HH HH  AAA   AA

(1 0 0)

 0 1 0 :HH HH     HH HH-|HH HH   HH HH  AAA   AA

 0 2 0 :HH HH     HH HH-|HH HH   HH HH  AAA   AA

 0 F 0 :HH HH     HH HH-|HH HH   HH HH  AAA   AA

(1 F 0)

PGDN:forward     PGUP:Fback    SPACE:Start     ESC:Exit

(1 1 0)

(1 2 0)

XXXXXXX

: The meaning of each SMART value is displayed.

If an unknown value is read, the ID number is displayed.

cur

: The current value of each item.

wor

: The worst value of each item in the past.

thr

: The lowest value at which each item operates normally.

Disk Controller Check test

[Error stop continue 1 pass]

Test Start ?[ Yes  No]

Pass count=xxxxx

Controller   Checking

ESC:Exit     PACE:Stop        Start

or

Smart ON/OFF

SMART [ON or OFF]

ESC:Exit

ENTER:Exceute

*

Smart Value Display

cur : wor : thr

cur : wor : thr

XXXXXXX : xxx : xxx : xxx

‚w‚w‚w‚w‚w‚w : xxx : xxx : xxx

‚w‚w‚w‚w‚w‚w : xxx : xxx : xxx

XXXXXXX : xxx : xxx : xxx

‚w‚w‚w‚w‚w‚w : xxx : xxx : xxx

Value Save ? [ YES NO ]

CURSOR: Move         ENTER: Select             ESC: Exit

UP-X300V

DIagnostics Specifications

3 – 9

Before execution of the write mode test
The caution message is displayed: [When executed, Data on hard disk will be
destroyed.]
When "184184" is entered with the keys, the parameter input menu is displayed.

Similar to the test (5) above. However, the following content differs. 

Test mode: 

 is displayed.

Similar to the test (11) above. 

Similar to the test (6) above. However, the following content differs.

Test mode: 

 is displayed.

Similar to the test (7) above. However, data in the HDD can be patched. 

Data patch is made as follows:
Data in the HDD are changed on the display to patch.

(Shift the cursor to the item to be changed with [

2 ], [ 4 ], [3], [1] keys,

and enter data with [0] ~ [F] keys.)
Then press [ENTER] key, and select "Yes" in "Update? (Yes No)" and

press [ENTER] key. (Shift the cursor with [

1] key.) By this procedure,

patch is executed.

The following error contents are obtained directly from the HDD controller.

[Error codes and meanings]

This test is used to check whether the full keyboard I/F section functions

normally or not. This test checks contact state of the signal pins and key
controller troubles. 

The following item is checked with this test. 

Use 106 keyboard to execute 106 keyboard I/F test. This test checks

contact state of the signal pins in the connector section. The layout of
106 keyboard is displayed on the display. When a key is pressed by the

operator, the key position is indicated with 

 mark on the display. The

operator must check that the pressed key position and the indicated
position on the display are the same.

However, the following keys cannot be checked. 

[PAUSE] [Print Screen]

On the above display, use [

2 ] and [ 4 ] keys to select a test item. When

[ENTER] key is pressed, the test is executed. When [ESC] key is

pressed, the display returns to the initial menu. 

The layout of 106 keyboard is displayed.
When any key of 106 keyboard is pressed, the code of the pressed key
is displayed.
KEY CODE: The key code value is displayed in HEX.

Data write -

is displayed. 

Data read - 

Data write -

is displayed. 

Data read - 

Error
code

Error message

0

OK!!
(The process is normally completed.)

1

Drive not ready
(HDD is not ready. STATUS REG bit6:0)

2

Bad contactor
(HDD controller abnormality. diag status error STATUS REG
bit5:1 or DIAG STATUS >=2)

3

Track 000 error
(TRACK 000 cannot be found with RESTORE command.
ERROR REG bit4:0)

4

Seek error
(Seek error occurs. After execution of SEEK command,
STATUS REG bit1 : 1)

5

ID not Found (ID field cannot be found. ERROR REG bit4:1)

When executed, Data on hard disk will be destroyed.

Operation press "184184" to  execute.

ESC:Exit

Cautions message

write

verify

write

verify

6

Data Address Mark not Found
(Data Address Mark cannot be found. ERROR REG bit0:1)

7

Bad Block Detect
(Bad block mark is recorded in the ID field of the requested
sector. ERROR REG bit7:1)

8

Uncorrectable Data Error
(An uncorrectable read error occurs. ERROR REG bit6:1) 

9

Other error
(Other error STATUS REG bit0:1 and ERROR REG:0)

10

Time out error
(Time out occurs when making an access to HDD.)

11

Compare error
(Write data do not match with read data.)

•  106 keyboard (OADG standard)

x 1

•  UP-X500 series main unit diag execution media

x 1

• 106 keyboard check

106 Keyboard check

106 keyboard check

:Move     ENTER:Select     ESC:EXIT

UP-X300V

DIagnostics Specifications

3 – 10

When [ESC] key of 106 keyboard is pressed twice continuously, the dis-
play returns to the menu of the test (1) above. 

• Parity error

(This error occurs when the serial data from the keyboard is of even parity.)

• Key recognizer error

(This error occurs when the entered key code cannot be recognized.)

This test is used to check whether the VGA I/F section and the LCD
panel function normally or not. Selection of aging/error stop/1 pass can
be made. The test execution time is also displayed. 

*Since the VGA test is executed for all display area, when the VGA test

item is selected, the display mode is switched to the all display mode. 

•  UP-X500 series main unit diag execution media x 1

The purposes of this test are as follows:

The LCD display test is executed in the following sequence:

This test is used to check ON/OFF of the LCD backlight.

The test procedures are as follows:

This test is used to check 18-color display and 8-color reverse and

blinking display. 

This test is used to execute the VRAM (1MB) memory verify test. 

The errors occurred in the previous tests (1) ~ (5) are displayed for each

test item. 

On the above display, use [

2 ] and [ 4 ] keys to select a test item. When

[ENTER] key is pressed, the test is executed. When [ESC] key is

pressed, the display returns to the initial menu. 

Refer to 5-5-4. (1).

ON/OFF of the backlight is repeated in a certain frequency. 

When [SPACE] key is pressed during this test, the test is interrupted. 

When [SPACE] key is pressed during interruption, the test is resumed. 

When [ESC] key is pressed, the test is terminated and the display

returns to the initial menu. 

•  Test pattern display

•  LCD backlight ON/OFF test

• LCD attribute test

• VRAM test

• Brightness test

• Error table

Test for
1 pass

All dot Black
(Check that all the display is black.)

All dot Black
(Check that all the display is black.)

All-dot white
(Check that all the display is white.)

8-dot unit check pattern display

8-dot unit

8-dot unit

Peripheral 1-dot display

Test for 1 pass

Backlight ON

4

Backlight OFF

LCD & VGA Diagnostics

Test Pattern display

LCD Reverse Display test

LCD Back-Light ON/OFF test

LCD Attribute test

:Move     ENTER:Select     ESC:Exit

Error table

VRAM test

LCD Back-Light ON/OFF Test

ON

(OFF)

SPACE:Stop

ESC:Exit