DOWNLOAD Sharp UP-X300 (serv.man45) Service Manual ↓ Size: 3.62 MB | Pages: 73 in PDF or view online for FREE

CODE : 00Z

q

CONTENTS

Parts marked with "!" are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.

UPX300VSME

UP-X300V   

This POS terminal contains a Lithium Battery. The battery must be disposed of properly.

Please contact Local Environmental Officials for disposal instructions.

THERE IS RISK OF EXPLOSION IF THE BATTERY IS REPLACED

BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING

TO THE "BATTERY DISPOSAL" INSTRUCTIONS.

AVOID SHORT-CIRCUITING THE BATTERY TERMINALS.

KEEP THE BATTERY AWAY FROM FIRE. 

* WHEN DISPOSING OF THE BATTERY, FOLLOW THE LOCAL 

RULES AND REGULATIONS. 

THIS PRODUCT CONTAINS A LITHIUM BATTERY.

THIS BATTERY MUST BE DISPOSED OF PROPERLY.

REMOVE THE BATTERY FROM THE PRODUCT AND CONTACT FEDERAL OR 

STATE ENVIRONMENTAL AGENCIES FOR INFORMATION ON RECYCLING AND 

DISPOSAL OPTIONS.

CE PRODUIT CONTIENT UN ACCUMULATEUR À LITHIUM.

CET ACCUMULATEUR USAGÉ DOIT ÊTRE TRAITÉ CORRECTEMENT.

ENLEVEZ L’ ACCUMULATEUR DU PRODUIT ET PRENEZ CONTACT AVEC VOTRE 

AGENCE ENVIRONNEMENTALE LOCALE POUR DES INFORMATIONS SUR LES 

MÉTHODES DE RECYCLAGE ET DE TRAITEMENT.

UP-X300V

Specifications

1 – 1

The terminal should be plugged into an outlet which has a dedicated ground.

Set the power switch to the ON ( I ) position after the terminal has been
properly plugged in.

When the power switch is turned on, the power indicator will light up. The
indicator will remain on even while the display’s backlight is off.

■

The LCD display may be tilted for the best viewing/operational angle.

The allowable angle of display is within 53 degrees as illustrated below.

Caution: Do apply excessive pressure to the LCD display.

Make sure to hold the body when pulling the display.

■

Caution: Please do not use this switch unless instructed to do.

Using this Reset switch may damage or delete data.

■

Magnetic card reader

Operator display
(touch panel)

Power indicator

■

AC power cord

Power switch
(located at the bottom cabinet)

Side cover

(supports connection for external peripherals
such as CD-ROM unit, FDD unit, mouse, etc.)

(Connection
for AT keyboard etc.)

(Turn frontwards to increase
 the volume turn backwards to
 decrease the volume)

Side cover

Side cover release lever
(located at the bottom cabinet)

■

[Purpose] This switch is used to initiate the POS terminal hardware reset.

[Outline] The Reset switch is a single shot type.

Depressing the switch inward (ON):will restart the system hardware (reboot).

V

Power supply

AC 230 ~ 240V

Power consumption

 43W

Ambient temperature
and humidity

5 to 35°C (41 to 95°F)

20 to 90%

External dimensions

 318(W) x 311(D) x 284(H)

Weight

 5.7kg

53

UP-X300V

Specifications

1 – 2

The UP-X500 has two 184-pin DIMM sockets.
(The RAM module is Locally Procured)

Maximum DRAM: 1 ea. 512Mbytes 184pin DIMM

Class: DDR-SDRAM: Type PC2100 (more than): power 2.5V

The UP-X500 Terminal has 3 COM ports which are RS232 interfaces.
Note: COM2 can be switched to supply +5V power, to pin-9, CI signal.

Important: The +5V power consumption of COM2 is a Max 500mA.

The UP-X300 offers the following standard interfaces may be used by
the application that is installed:

The UP-X300 has the following Device interface connections.

Caution: UP-P20DPB and UP-I20DP can not be used simultaneously.

Item

Specifications

Note

CPU

VIA Eden Processor

733MHz

Chip set

VIA VT8623+VT8235

Graphics Chip

VIA VT8623

Main memory

128Mbytes 

DDR-SDRAM

MAX.512Mbytes

Video memory

16Mbytes

(Shared with Main memory)

Super I/O

SMSC SIO10N268

BIOS memory

512Kbytes

Flash ROM

Item

Specifications

Note

LCD type

TFT LCD

HT12x12-100

Screen size

12.1”

Resolution

XGA (1024 x 768 dots)

Module Size

261.5 (W) x 199.5 (H) x 5.5 (D)

Dot Size

0.240 x 0.240 (mm)

Active Area

245.8 x 184.3 (mm)

Item

Specifications

Note

Type

Analog touch panel

N010-0554-T802

Module Size

261.4(W) x 198.8(H) x 2.8(D) (mm)

Viewing Area

247.7(W) x 186.5(H) (mm)

Active Area

246.5(W) x 185.3(H) (mm)

Number of
Positions

4096 x 4096 Positions

Item

Specifications

Note

Controller

VT6103

Speed

10Mb/s or 100Mb/s

connector

RJ45

COM1,COM2,COM3

: D-sub 9 pin
: Pin Description

Pin-1: CD

Pin-2: RD
Pin-3: SD

Pin-4: ER

Pin-5: GND
Pin-6: DR

Pin-7: RS

Pin-8: CS
Pin-9: CI/+5V

Item

Specifications

Note

Type

Compact Flash memory  HAGIWARA SYS-COM

CFC-1284MBA

Interface

True IDE

Capacity

128 Mbytes

•  CF CARD interface

: 1 port (True IDE)

• USB2.0 interface

: 2  ports

Power consumption

: +5V max. 0.5A

• PS/2 interface

: 1  port

• VGA interface

: 1  port

• Drawer I/F

: used for ER-03DW, ER-03DWB7, 

ER-04DW

•  Customer display I/F

: used for UP-P20DP/DPB or UP-I20DP

•  Magnetic Card Reader interface : 1 port (3-Track)

•  RS-232C Serial ports

: 3 x D-Sub 9-pin