Sharp UP-3500 (serv.man34) User Manual / Operation Manual ▷ View online
36
3
IRC Programming
To start IRC programming, first, turn on the machines in the IRC system and put them in the PGM2 mode.
The programming procedures for both the master and satellites will be explained below.
The programming procedures for both the master and satellites will be explained below.
For the setup of your IRC system, please be sure to consult your authorized SHARP dealer.
It is necessary to assign machine numbers to the master and satellites before programming.
1.
Enter the PGM2 mode from the mode selection window.
2.
Select “2 SETTING” from the displayed menu.
The SETTING window will appear.
3.
Select “8 TERMINAL” from the displayed menu.
The TERMINAL window will appear.
4.
Touch the “MACHINE#” line from the displayed items.
Enter a desired number for the machine, and touch the [Exit] key.
Machine number: up to 6 digits (0–999999)
The DATA NOT SAVED SAVE IT? dialogue will appear.
Machine number: up to 6 digits (0–999999)
The DATA NOT SAVED SAVE IT? dialogue will appear.
5.
Select “1.SAVE.”
6.
Repeat steps 1 to 5 for all machines in the IRC system.
• In an IRC network, each machine number must be unique. Do not use the same number for
two or more machines.
• Be sure to set up satellites first to allow the downloading of inline preset from the master to
satellites.
NOTE
1. Setting the machine numbers – master and satellite
37
For the setup of your IRC system, please be sure to consult your authorized SHARP dealer.
It is assumed that your IRC terminals have been set for inline operations.
It is assumed that your IRC terminals have been set for inline operations.
1.
Enter the PGM2 mode from the mode selection window.
2.
Select “2 SETTING” from the displayed menu.
The SETTING window will appear.
3.
Select “21 INLINE CONFIG” from the displayed menu.
The INLINE CONFIG window will appear.
4.
Touch the “IP ADDRESS 4” line from the displayed items.
Enter a desired terminal number (1-254) for the machine, and touch the [CONTINUE] key.
(For programming for the SYSTEM RETRY function and the LOOKUP ORDER, see page 41.)
5.
Repeat steps 1 to 4 for all machines in the IRC system.
• Terminal numbers must be assigned to the master and each satellite in the IRC system.
(For setting the master’s terminal number, see the next paragraph.)
• If an IRC network contains two or more machines with the same terminal number, IRC
communications will not be achieved correctly. Each terminal number must be unique.
• The terminal number should be in the range from 1 to 254.
• If the terminal number “000” is programmed for a machine, it is put in the OFF LINE mode and
• If the terminal number “000” is programmed for a machine, it is put in the OFF LINE mode and
cannot take part in IRC communications.
NOTE
2. Setting the terminal numbers (IRC machine numbers) for satellites
38
For the setup of your IRC system, please be sure to consult your authorized SHARP dealer.
(1) Setting the terminal number for the master and creating the master list
A master list can only be created on the pre-designated master.
1.
Enter the PGM2 mode from the mode selection window.
2.
Select “2 SETTING” from the displayed menu.
The SETTING window will appear.
3.
Select “21 INLINE CONFIG” from the displayed menu.
The INLINE CONFIG window will appear.
4.
Enter a terminal number (1–254) for the master in the “IP ADDRESS 4” line and carry out the
programming for BMA MACHINE NO.*, the SYSTEM RETRY function*, and LOOKUP ORDER*, and
then touch the [CONTINUE] key.
programming for BMA MACHINE NO.*, the SYSTEM RETRY function*, and LOOKUP ORDER*, and
then touch the [CONTINUE] key.
The MASTER LIST window will appear.
(*For programming for BMA MACHINE NO., the SYSTEM RETRY function and LOOKUP ORDER, see
pages 40–41.)
pages 40–41.)
5.
Enter a terminal number (1–254) for a machine in the IRC system in the “IP ADDRESS 4” line, and then
touch the [ENTER] key.
touch the [ENTER] key.
The “MACHINE No.” line will be selected for entry.
6.
Enter the machine number (1–999999) of the machine and touch the [ENTER] key.
7.
Repeat steps 5 to 6 for all machines in the IRC system.
Touch the [CONTINUE] to complete the master list.
Touch the [CONTINUE] to complete the master list.
• The terminal numbers and machine numbers of the master and satellites must be entered into
the master list for IRC communications.
• The terminal numbers and machine numbers of up to 32 machines (one master and 31
satellites) can be entered into the master list.
• The terminal number should be in the range from 1 to 254 and the machine number from 1 to
999999.
• No satellite can perform inline communications unless its terminal and machine numbers are
present in the master list.
• If a machine number which already exists in the master list is entered, an entry error will occur
even when the corresponding terminal number does not exist in the list.
• Even if a set of terminal and machine numbers that exists in the master list is entered, no error
will occur (the list will remain unchanged.)
NOTE
3. Initial setting for the master and master list creating/updating
39
(2) Deleting a machine from the master list
To delete a terminal number from the master list, proceed as follows:
1.
Enter the PGM2 mode from the mode selection window.
2.
Select “2 SETTING” from the displayed menu.
The SETTING window will appear.
3.
Select “21 INLINE CONFIG” from the displayed menu.
The INLINE CONFIG window will appear.
4.
Touch the [CONTINUE] key.
The MASTER LIST window will appear.
The MASTER LIST window will appear.
5.
Enter a terminal number in the “IP ADDRESS 4” line and a corresponding machine number in the
“MACHINE No.” line of a machine to be deleted , and then touch the [
“MACHINE No.” line of a machine to be deleted , and then touch the [
] key.
6.
The machine will ask you as follows: “ARE YOU SURE?”
If you are sure to delete it, select “1.YES.” If not, select “2.NO.”
7.
Repeat steps 5 to 6 for all machines to be deleted.
8.
Touch the [CONTINUE] key to complete the master list.
• You can delete any of the terminal numbers that are in the master list.
• Deleting the master from the master list will inhibit all requests of the satellites from being sent.
• Deleting the master from the master list will inhibit all requests of the satellites from being sent.
NOTE
RECORD
DELETE
Click on the first or last page to see other UP-3500 (serv.man34) service manuals if exist.