Sharp UP-800 (serv.man32) User Manual / Operation Manual ▷ View online
3
Introduction
The UP-800F/UP-810F inter-register communication (IRC) system consists of one master machine and up
to 31 satellite machines which are all interconnected by the local area network (LAN) to provide data
transmission among them. This system allows the manager to exercise centralized control over the satellites
through the master.
to 31 satellite machines which are all interconnected by the local area network (LAN) to provide data
transmission among them. This system allows the manager to exercise centralized control over the satellites
through the master.
• One of the satellites may be used as a back-up master.
The additional RAM board, UP-S04MB2, must be installed in the master and, if possible, in each
satellite.
satellite.
NOTE
LAN
Master
Satellite
Max. 31 satellites
Satellite
4
1
Inline Operation
(1) Message displayed during inline communication
1)The message as shown below is displayed at the master which is engaged in IRC transmission.
ex.:
The above message is also displayed at the satellite which is engaged in transmission for
system resetting.
system resetting.
2)The machine number of the satellite communicating with the master is displayed at the master after
the start of IRC transmission.
ex.:
In this case, the machine number of the satellite is “000022.”
000022
NOTE
SENDING DATA
1. Message display
5
(2) Error messages
If an error occurs, a corresponding error message is displayed.
To clear an error message, press the
To clear an error message, press the
L
key.
For error messages, see the table below.
List of error messages
Error messages (Default)
Description
• This message prompts you to retry communication with the machine which you
have failed to communicate.
• The target machine is busy.
• The specified clerk has signed on at another machine.
• The entered GLU code is in use.
• The GLU code or related file memory is not enough.
• Transmission error
• The remote printer did not operate correctly.
• The clerk who entered a GLU code are not authorized.
• IRC initial downloading before resetting
• The back-up master doesn't reply to the request.
• The master doesn't reply to the request.
• Remote printer off-line error
• The target machine is turned off.
• T-LOG buffer is full.
• The file in the master and that in the satellite are not of the same type.
• The specified clerk code is not present in the master list.
• The entered GLU code is not listed.
• The entry made is not valid.
RETRY
BUSY
CODE NOT FREE
LACKING MEMORY
LINE ERROR
MOTOR LOCK
NO AUTHORITY
NON RESET
BACKUP DOWN?
MASTER DOWN?
OFF LINE
POWER OFF
T-LOG FULL
TYPE ERROR
UNDEFINED CODE
ENTRY ERROR
6
When the open store operation is performed at the master, the IRC system is opened. POS can send AT
command by this job. This function controls a modem, but doesn't have control over registration and T-LOG.
The procedure for the open store operation is as follows.
command by this job. This function controls a modem, but doesn't have control over registration and T-LOG.
The procedure for the open store operation is as follows.
Select “OPEN STORE” from the OPXZ mode window and press
the
the
e
key.
• You can also perform the open store operation at each satellite.
• The open store operation cannot be performed at any machines whose terminal numbers have
• The open store operation cannot be performed at any machines whose terminal numbers have
not been programmed.
• When a transmission error occurs while the open store operation is being performed, the open
store operation is regarded as normally terminated if the system retry function* has been
disabled by programming. When the master has been programmed to enable the system retry
function, it displays the machine number of the satellite that has encountered the error.
Selecting the displayed machine number will display a prompt to retry the open store operation.
disabled by programming. When the master has been programmed to enable the system retry
function, it displays the machine number of the satellite that has encountered the error.
Selecting the displayed machine number will display a prompt to retry the open store operation.
* For the system retry function, see page 63–64.
NOTE
2. Open store operation (OPXZ mode) – master and satellite
Click on the first or last page to see other UP-800 (serv.man32) service manuals if exist.