Sharp BD-HP21H (serv.man10) User Manual / Operation Manual ▷ View online
19
Connection
o
Audio Connections
This Player
Connecting the Audio Jacks
You can connect audio equipment or the TV to the 2CH AUDIO output jacks.
•
Audio equipment with audio jacks
STEPS
Be sure to turn off this Player and the equipment before making any connections.
Firmly connect the AV cable (supplied) to the audio jacks (
Firmly connect the AV cable (supplied) to the audio jacks (
1 and 2).
1:
2:
2:
To 2CH AUDIO
output jacks
output jacks
To audio input
jacks
jacks
(White)
AV cable (supplied)
Amplifier
1
(Red)
(White) (Red)
TV
2
After connecting
Load a disc and start playback. (Pages 24-27)
•
BD-HP21H_en.indd 19
BD-HP21H_en.indd 19
2008/08/05 15:55:54
2008/08/05 15:55:54
20
Loading the Batteries in the Remote
Control
Control
Hold in the tab on the battery cover and pull the
cover towards the direction of the arrow.
cover towards the direction of the arrow.
Load the two “AA” size batteries (R-06 size,
UM/SUM-3). Place batteries with their terminals
corresponding to the
UM/SUM-3). Place batteries with their terminals
corresponding to the
m and n indications in
battery compartment.
Insert the smaller tab of the battery cover into
the opening
the opening
1, and press down on the cover
until it clicks in place
2.
NOTE
Do not subject the remote control unit to shock, water or
excessive humidity.
The remote control unit may not function if the Player's remote
sensor is in direct sunlight or any other strong light.
Incorrect use of batteries may cause them to leak or burst. Read
the battery warnings and use the batteries properly.
Do not mix old and new batteries, or mix different brands.
Remove the batteries if you will not use the remote control unit for
an extended period of time.
excessive humidity.
The remote control unit may not function if the Player's remote
sensor is in direct sunlight or any other strong light.
Incorrect use of batteries may cause them to leak or burst. Read
the battery warnings and use the batteries properly.
Do not mix old and new batteries, or mix different brands.
Remove the batteries if you will not use the remote control unit for
an extended period of time.
•
•
•
•
•
•
1
2
3
Connecting the Power Cord
Plug the supplied AC cord into the AC IN terminal on the rear
of the Player. Then plug into AC outlet.
of the Player. Then plug into AC outlet.
NOTE
Place the Player close to the AC outlet, and keep the power plug
within reach.
TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT TOUCH THE
UN-INSULATED PARTS OF ANY CABLES WHILE THE AC CORD
IS CONNECTED.
The
within reach.
TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT TOUCH THE
UN-INSULATED PARTS OF ANY CABLES WHILE THE AC CORD
IS CONNECTED.
The
a (STANDBY) indicator blinks while the Player is preparing for
starting up. You cannot turn the Player on until the
a (STANDBY)
indicator stops blinking.
•
•
•
Before Starting Playback
Approximate operating range of remote
control
control
Remote control sensor
Remote control unit
30º
30º
7 m
To AC IN terminal
To AC outlet
Disc Playback
BD-HP21H_en.indd 20
BD-HP21H_en.indd 20
2008/08/05 15:55:56
2008/08/05 15:55:56
21
p
Disc Playback
Operating the TV of SHARP
Using the Remote Control
Using the Remote Control
The Universal Remote Control may operate the
basic functions of the TV of SHARP.
basic functions of the TV of SHARP.
TV function control
TV Power:
B
TV Channel up/down: P
r/s
TV Volume up/down:
i
e/f
TV-AV Selector:
b
•
•
•
•
•
•
•
Setting the Remote Control
Code
Code
3 types of remote control codes operate this
Player: RC-1, RC-2 and RC-3. If you operate
this Player by remote control along with another
SHARP Blu-ray Disc Player or DVD Player placed
next to it simultaneously, switching the remote
control code (both the Player and remote control)
to one of the signals (RC-1, RC-2 or RC-3) will let
you operate only with this Player.
Make sure to set the Player and remote control to
the same remote code. You can not operate the
Player if they are not set to the same code.
Player: RC-1, RC-2 and RC-3. If you operate
this Player by remote control along with another
SHARP Blu-ray Disc Player or DVD Player placed
next to it simultaneously, switching the remote
control code (both the Player and remote control)
to one of the signals (RC-1, RC-2 or RC-3) will let
you operate only with this Player.
Make sure to set the Player and remote control to
the same remote code. You can not operate the
Player if they are not set to the same code.
Setting the Remote Control
Code of the Remote
Code of the Remote
Example: Setting the code to “RC-3”.
Press and hold 3 first and then
B
on the remote control together for
more than 5 seconds.
more than 5 seconds.
Press
B (on the player) to turn off
the player.
Setting the Remote Control
Code of the Player
Code of the Player
Point the remote control at the
player, then press and hold the
DISPLAY button for more than 10
seconds.
player, then press and hold the
DISPLAY button for more than 10
seconds.
Press
B (on the remote control) to
turn on the player.
•
•
1
2
3
4
Before Starting Playback
B
(POWER)
Remote control sensor
BD-HP21H_en.indd 21
BD-HP21H_en.indd 21
2008/08/07 17:40:24
2008/08/07 17:40:24
22
Turning the Power On
Turning the power on
Press
B on the remote control or on the
Player to turn on the power of the Player.
Entering standby
Press
B on the remote control or on the
Player to enter standby.
If you press
B again immediately after entering
standby, the Player may not turn on. If this
happens, wait for 10 seconds or more and then
turn on the power again.
happens, wait for 10 seconds or more and then
turn on the power again.
NOTE
When the
a (STANDBY) indicator is blinking (may
take some time), the Player cannot be turned on.
•
Indicators on the Player
I (ON) indicator
Green on
Power on
a (STANDBY) indicator
Red blinks
Preparing for standby
Red on
Standby
BD/DVD/CD mode indicator
Off
No disc
Blue on
Playing back
White on
Disc stopped
White blinks
Loading a disc
When you turn on the POWER, the MENU screen
automatically displays for a while.
Press EXIT to erase the display.
automatically displays for a while.
Press EXIT to erase the display.
•
•
Language Setting
Changing the on-screen
display language
display language
Press SETUP to display the SETUP
MENU screen.
MENU screen.
Press
a/b/c/d to select “ON
SCREEN LANGUAGE”, then press
ENTER.
ENTER.
DISPLAYS THE TITLE LIST
SETTINGS
ON SCREEN LANGUAGE
PICTURE
Press
a/b/c/d to select the
language you want to display on the
screen, then press ENTER.
screen, then press ENTER.
ENGLISH
SVENSKA
NEDERLANDS
PORTUGUÊS
DEUTSCH
ESPAÑOL
FRANÇAIS
ITALIANO
NOTE
To select the DVD disc language, such as subtitle
language, etc., see page 25.
language, etc., see page 25.
•
1
2
3
Before Starting Playback
B (POWER)
BD/DVD/CD mode indicator
a (STANDBY) indicator
I (ON) indicator
BD-HP21H_en.indd 22
BD-HP21H_en.indd 22
2008/08/05 15:56:00
2008/08/05 15:56:00
Click on the first or last page to see other BD-HP21H (serv.man10) service manuals if exist.